Benutzeranleitung / Produktwartung EC-PM-520 des Produzenten EC Line
Zur Seite of 41
EC-520 User ’s Manual - i - Import ant Safety Instruction Be sure to have read the manual carefully before y our operation. Neither our Corporation nor its affiliates shall be liable to the purchase.
EC-520 User ’s Manual - ii - T able of content s Import ant Safety Instruction ................................................................................................... ................i Chapter 1 Overview .................................
EC-520 User ’s Manual - 1 - Chapter 1 Overview 1.1 Printer T ypes EC-520 ( micro bill printer ) are series products developed by our Corporation according to different requirement and dif ferent using environment. “TP” means micro printer , “220” means printer type, “C” means having paper cutter module.
EC-520 User ’s Manual - 2 - Figure 1-3 Main parts of printer （ backwards ） Roll Paper Cover Paper Ladle 57.5mm Partition Board Ribbon Cassette Ribbon Knob Ribbon Cassette Cove r Power Switch Ope.
EC-520 User ’s Manual - 3 - Chapter 2 Inst allation 2.1 Unp acking Check the pack list as following (See t he Figure 2-1). It includes the following items: （ 1 ） Printer; （ 2 ） Power cord; （ 3 ） Interface cable; （ 4 ） AC adapte r; （ 5 ） 57.
EC-520 User ’s Manual - 4 - 2.3.1 Connecting the Cash drawer Cable Make sure the printer is turned off. Plug the inte rface cable into the cash drawer connector of the printer and the other end connector to cash drawer . Must use the cash drawer foll owing the requir ement noted by T able A-1 (Part 5.
EC-520 User ’s Manual - 5 - 2.3.4 Connecting the Se rial Interface Cable 1. Make sure that the host computer and the printer are both turned off, connect the serial interface cable to the connecto r of the printer and tighten the screws as shown in Figure 2-5.
EC-520 User ’s Manual - 6 - 2.4 Connecting the Power Supply 1. Make sure the power switch is in the OFF pos ition (when the pre ssed side of power switch is in the “O” position). 2. Check and ensure the voltage supplied from elec trical outlet is matching with the printer ’ s specification.
EC-520 User ’s Manual - 7 - Note: 1. When printed characters begin to appear feint, it is time to replace the ribbon cassette. If not, it will affect the print quality or even damage the print head. 2. Before replacing the ribbon cassette, make sure the printer is turned off.
EC-520 User ’s Manual - 8 - 2.6 Inst alling the Driver Install the driver after connecting the host computer , insert the driver disk to the computer , and then follow the steps below: Auto-inst all w ay Double click the file "Setup.exe" in the driver disc, install driver by the following direct.
EC-520 User ’s Manual - 9 - Chapter 3 Control Panel 3.1 Control Panel There are three LEDs and one key on the c ontrol panel as shown in Figure 3-1. 3.1.1 Indicator LEDs LED On Blinks Off POWER Power on —— Power off P APER OUT Paper out ; Alarm voice is emitted.
EC-520 User ’s Manual - 10 - 3.2 Printer Default Setting 3.3 Explanation for Printer setting Items 1. Through the inside setting of the printer (EC-520, with Parallel Interface or USB Interface), you can set the following items: black mark setting 、 print direction , p aper width.
EC-520 User ’s Manual - 1 1 - “No check mode” is the factory default setting. ④ Dat a Length Data length is pre-set by 8 bits with no change. ⑤ Stop Bit S top bit Data length is pre-set by 1 bit with no change. ⑥ Control mode DTR/DSR, XOFF/XON; “DTR/DSR” is the factory default setting.
EC-520 User ’s Manual - 12 - ■ Print-Pins T est While pressing the FEED key and holding on, turn on the printer . The printer sounds two beeps, and you should release the FEED key at the same time. The printer will print the print-pins test. As shown in the following figure.
EC-520 User ’s Manual - 13 - NOTE ： Adjustment of column can have effect on printing quality . Y ou must think carefull y before adjusting and must operate strictly according to instruction. ■ Hexadecimal Printing Mode While pressing the FEED key and holding on, turn on the printer.
EC-520 User ’s Manual - 14 - 5. The setting way is corresponding wi th that of printer menu system. In the “Printer Settings” layout, select the first class menu in the combo box of “Select Printer Setting Class”, select the second menu in the “Configuration” and set the item in the current parameters list.
EC-520 User ’s Manual - 15 - Chapter 4 Loading Paper The printer can use the paper with the width 76mm or 57.5mm, and it is easy to load paper . How to load paper will be introdu ced in this chapter . 1. Press the open button to open the roll paper cover .
EC-520 User ’s Manual - 16 - Chapter 5 Specifications 5.1 Basic Specifications Printing method Dot matrix im pact Printing Direction Bidirectional wizard Printing width 42 columns / 63mm (76mm paper wid th) 30 columns / 45mm (57.5mm paper wid th) Printing Speed: 4.
EC-520 User ’s Manual - 17 - Operating panel 1 key and 3 indicator lights Paper T ype Roll paper Paper Specifications Paper W idth: 76mm or 57.5mm Paper W eight: 52.3~64.0 g/ m 2 Paper Thickness: 0.06~0.20mm Outer Diameter: 83m m (3.27’ ’) max. Inner Diameter : 10mm (0.
EC-520 User ’s Manual - 18 - 5.2 Interface 5.2.1 Cash drawer Connector (1) The cash drawer connector on rear panel of printer is RJ-1 1 connecto r (6 lines), shown as below . (2) Definition of pins The definition of the cash drawer connec tor pins is shown as the T able below: T able A-1 Definition of the Cash drawer Connector Pins Pin NO.
EC-520 User ’s Manual - 19 - T able A-2 Pin function of p arallel interface connector Pin return Signal name Direction Description 1 19 /STROBE Data selected IN Width of selected pluse is 0.
EC-520 User ’s Manual - 20 - 32 /ERROR Error happens with printer. Out When the printer is in state of paper out, offline condition or error, this signal level becomes low. 33 GND Ground --- Same with 19 ～ 30 pins. 34 NC Empty pin --- This pin is empty.
EC-520 User ’s Manual - 21 - 5.2.3 USB Interface 1. The USB interface connector is USB-B type (as shown by figure 5-4): 2. The connecting figure of printe r and computer with USB interface (as shown in figure 5-5). USB Interface is 2.0 Full-S peed interface, and displayed as an USB port in the computer finally .
EC-520 User ’s Manual - 22 - (3) Definition of pins Definition of each pin of RS-232 serial interface is shown in T able A-3: T able A-3 Definition of pins of RS-232 serial interface Pin NO.
EC-520 User ’s Manual - 23 - Chapter 6 Printer ’ s maintenance 6.1 Clean the Printer It’s necessar y to clean the printer periodically . Interval and Material for cleaning Interval ： Every 6 months or 300 hours of working time. Material ： Dry cloth （ soft cloth for meta l parts ） .
EC-520 User ’s Manual - 24 - Phenomenon: Paper out LED is on and cannot print; Or the printing action stops suddenly while printing, and paper out LED is on; and at the same time the alarm voic e is presented by the printer . Reason: Paper out Solution: Install p aper roll once again, the printer wil l resume normal.
EC-520 User ’s Manual - 25 - Chapter 7 Command Code Summary 7.1 General The EC-520 printer‘s control commands are compatible with ESC/POS. Explanation of every command include format and de scription. ”Format ” part s give three kinds of command format including ASCII Code, Decimal code and hexadecimal code.
EC-520 User ’s Manual - 26 - FF Print a nd change page Format ： ASCII ： FF Decimal ： 12 Hex ： 0C [Description] Prints one line data in the line editing buf fer and f eeds to the top of next page based on the current page length.
EC-520 User ’s Manual - 27 - ESC & Define user -defined characters Format ： ASCII ： ESC & s n m a d1 d2 …… db Decimal ： 27 38 s n m a d1 d2 …… db Hex ： 1B 26 s n m a d1 d2 …… db [Description] This command is used for self-def ining characters.
EC-520 User ’s Manual - 28 - ESC - T urn u nderline mode on/off Format ： ASCII ： ESC - n Decimal ： 27 45 n Hex ： 1B 2D n [Description] n=0, turns off underline mode; n=1, turns on underline mode. ESC 2 Set 1/6 inch line spacing Format ： ASCII ： ESC 2 Decimal ： 27 50 Hex ： 1B 32 [Description] Set the line spacing to 1/6 inch.
EC-520 User ’s Manual - 29 - Format ： ASCII ： ESC C n Decimal ： 27 67 n Hex ： 1B 43 n [Description] The command sets the length of detecting black mark in the meantime. If the black mark can’t be detected in this length, th en it is considered that the p aper has no black mark.
EC-520 User ’s Manual - 30 - When double-strike mode is turned on, the same c haracter will be printed twic e in the same position. • When n is 0, double-strike mode is turned off.
EC-520 User ’s Manual - 31 - • When n ＝＜ *******0 ＞ B, all buttons are enabled (Default) . • When n ＝＜ *******1 ＞ B, all buttons are disabled. ESC d Print and feed n lines Format ： ASCII ： ESC d n Decimal ： 27 100 n Hex ： 1B 64 n [Description]Prints the data in t he print buf fer and feeds n lines.
EC-520 User ’s Manual - 32 - ESC v transmit printer st atus Format: ASCII: ESC v Decimal: 27 1 18 Hex: 1B 76 [Description] This command is effective by using serial interface, and its function is to transmit the status of paper sensor as 1 byte of data.
EC-520 User ’s Manual - 33 - FS 2 Self-define Chinese characters Format: ASCII: FS 2 a1 a2 d1 d2 d3 …d32 Decimal: 28 50 248 a2 d 1 d2 d3 …d32 Hex: 1C 32 F8 a2 d1 d2 d3 d32 [Description] Defines the user-defined Chinese characters. a1=F8 (Hex); A1 ≤ a2 ≤ FE (Hex).
EC-520 User ’s Manual - 34 - GS （ F set offset of black mark for printing and cutting position Format: ASCII: GS （ F pL pH a m nL nH Decimal: 29 40 70 pL pH a m nL nH Hex: 1D 28 46 pL pH a m nL nH [Description] The parameters set by this command will be va lid even after the printer is restarted.
EC-520 User ’s Manual - 35 - position offset from the beginning print-posit ion is same with the inherent mechanical value Q 0 of the printer (shown as figure 7-2) , all the offset value set by “GS （ F” command is 0.
EC-520 User ’s Manual - 36 - GS r Transmit printer status Format: ASCII: GS r n Decimal: 29 114 n Hex: 1D 72 n [Description]This command is effe ctive at serial interface. If n=1 or n=49, paper status is returned. If paper is present, the bit2, 3 of t he returned byte is 0; if paper is not present, the bit 2, 3 of the returned byte is 1.
EC-520 User ’s Manual - 37 - Appendix. Commands List Control Code Hexadecimal Code Function HT 09 Horizontal tab LF 0A Print and line feed CR 0D Print and carriage return FF 0C Page mode print and r.
EC-520 User ’s Manual - 38 - GS ( A pL pH n m 1D 28 41 pL pH n m Test command G S ( F p L pH a m nL nH 1D 28 46 pL pH a m nL nH set offset of black mark for printing and cutting position GS r 1D 72 .
Manufactur ed from: EC Printer.
Ein wichtiger Punkt beim Kauf des Geräts EC Line EC-PM-520 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie EC Line EC-PM-520 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für EC Line EC-PM-520 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von EC Line EC-PM-520 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über EC Line EC-PM-520 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon EC Line EC-PM-520 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von EC Line EC-PM-520 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit EC Line EC-PM-520. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei EC Line EC-PM-520 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
