Benutzeranleitung / Produktwartung SB730 des Produzenten EAW
Zur Seite of 28
KF730 & SB730 LOUDSPEAKER OWNER’S MANUAL Including KF730P & SB730P EAW Part: RD0169.
Page 2 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL.
Page 3 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL TABLE OF CONTENTS 1. READ THIS FIRST ................................................................................................................ 4 1.1 EC Statement Of Conformity ........
Page 4 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL 1. READ THIS FIRST 1.1 EC STATEMENT OF CONFORMIT Y This document confirm s that the range of p rod ucts of Eastern Acoustic Works be aring t.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 5 of 28 2. INTRODUCTION The KF730 Line Array represents E AW’s latest technology for arrayable loudspe akers. The KF730 is a small format line a rray system for venues with listener distances u p to about 200 ft / 65 m.
Page 6 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL 4. KF730 ARRAY DESIGN 4.1 KF730 WIZARD Use the KF730 Wizard for designin g KF730 arrays. It can be found in the Download s/Software section of the EAW we bsite (www.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 7 of 28 The horizontal pattern also features “soft sho u lders” that provide consistent frequency response to well beyond the nominal -6 dB points. These soft should ers can provide up to 150° of “usable ” horizontal coverage, albeit at somewhat reduced lev el.
Page 8 of 28 RD0169 ( A) KF730 & SB730 OWNER’S MANUAL When flown as part of a KF730 array, the SB730 s should be th e uppermost enclosure s in the array. In this application, the SB730s are su spended flat-fronte d, with the KF730s suspended below in the curvature determined by the KF730 Wizard.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 9 of 28 5. ARRAY OPERATION 5.1 OVERVIEW The operation of a KF730 Series system involves: 1. Understanding the principles on which it operate s. 2. How to electronically configure it for a specific task.
Page 10 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 5.4.1 Factory Signal Processing Settings The signal proce ssing adjustments determin ed by EAW for the KF730 Series Array should be fully implemented “as is.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 11 of 28 The following tables list th e rms voltage limits for the KF730 and SB730. Because of th eir higher impedance design, multiple KF730s an d SB730s ca n be powered from single a mplifier chan nels.
Page 12 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 5.7.3 Selecting an Appropriate Amplifier Size Rule Of Thumb If a KF730 Line Array is used for professionally opera ted co nce rt applications, a rule of thumb can be applied.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 13 of 28 5.8.2 SB730 Connections There are three Neutrik NL4MP and one NL 8MP connectors on the rear of each SB730. The connectors mate, respectively, with Neut rik NL4FC and NL8FC in-li ne cable connectors.
Page 14 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 5.8.4 KF730P Input Connection s There are two 4-terminal bar rier strip connectors on the rear of each KF730P. The connectors are wi red in parallel so that the second connector can be used to loop LF and MF/HF signals to additional KF73 0s.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 15 of 28 6. RIGGING KF730 Series arrays are intended to be suspende d or ground-stacked. Thi s chapter details how to physically configure KF 730 Series arrays. The following are the recommended method s for most situations.
Page 16 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL For a given quantity of SB730: Max quantity KF730 = 18 - (1.5 x quantity SB730) Example, given five SB730: 18 - (1.5 x 5) = 10.5 which rounds down to a maximum quantity 10 KF730s For a given quantity of KF730: Maximum quantity SB730 = (18 - quantity KF730) / 1.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 17 of 28 6.4.3 Quick Release Pins Each KF730 is supplied with six 1.5 inch Q uick Release Pins. Four are used for attaching enclosures together or to the Fly-Ba r. Two are used as locking pins for the rear Hin ges.
Page 18 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL KF730 FLY-BAR HINGE TUBE HOLES DANGER: Each Hinge Tube on the Fly-Bar has two Quick Relea se Pin holes. When suspending KF730 or SB730s from the Fly-Bar, always use t he upper hole for attaching the encl osure Hinges.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 19 of 28 6.5 PALLETS 6.5.1 KF730 Face Pallet The KF730 Face Pallet is a wheeled pallet that holds two KF7 30s face down. Routing on the underside of the pallet al lows stacking loaded pallets two hig h.
Page 20 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 6.7 SUSPENSION PROCEDURE S The basic procedure for suspending KF730s and SB 730s or a combination of both is si milar. What varies is how different pallet s affect ha ndling of the enclosures wh en being suspended.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 21 of 28 6.7.4 Attaching SB730s to SB730s Already Suspended NOTE: SB730s should always be flown tight-pa cked to each other. 1. Move an SB730 Pallet so its SB730 is positi oned under the bottom SB730 of the array.
Page 22 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 5. Attach each Hing e to the Hinge Tube b y in serting a Quick Release Pin (removed in Step 2) through both. 6. Insert a Quick Release Pin (removed in ste p 2) into each of the enclosure’s rear Hinge Tubes as a locking pin.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 23 of 28 6.8.2 Stacking Additional Enclosures (SB730 as th e base) CAUTION: When attaching Hinges to Hi nge Tubes in st ep 5 fo r an SB730, position the SB730 so it lies flat on the SB730 below it.
Page 24 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 6.8.5 Stacking Additional Enclosures (Fly-Bar as the base) CAUTION: When attaching Hinges to Hi nge Tubes in st ep 5 fo r an SB730, position the SB730 so it lies flat on the SB730 below it.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 25 of 28 7. CONTACTING EAW We have tried to answer any questions you ma y have about the KF730 and SB730 in this manual and in the KF730 Wizard Help file. Should you need further a ssistance, please d o not hesitate to contact us.
Page 26 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL 8. SERVICE AND MAINTENANCE 8.1 GENERAL SERVICE For any faults that cannot be fi eld-repaired a s noted below, contact the EAW Serv ice Department listed in Chapter 7 to determin e the appropriate action.
RD0169 (A) KF730 & SB730 OW NER’S MANUAL Page 27 of 28 8.4.2 Periodic Inspection Perform complete and thoroug h inspections on a routine, periodi c basis. The interval bet ween inspections and scope of the in spections will depend on the frequency of system usage and the conditions of use.
Page 28 of 28 RD0169 ( A) KF730 & SB730 OWNER’S M ANU AL © 2004 EASTERN ACOUSTIC WORKS ONE MAIN STREET WHITINSVILLE, MA 01588 2004 Mar RD0169.
Ein wichtiger Punkt beim Kauf des Geräts EAW SB730 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie EAW SB730 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für EAW SB730 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von EAW SB730 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über EAW SB730 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon EAW SB730 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von EAW SB730 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit EAW SB730. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei EAW SB730 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
