Benutzeranleitung / Produktwartung 2011 Ram Truck Chassis Cab des Produzenten Dodge
Zur Seite of 472
C HAS S I S CAB Chrysler Group LL C OWN ER’S MAN U AL 2011 2011 RAM TR UC K C HASS I S CAB 11DD43-126-AC Second Edition Printed in U.S.A. RAM TRUCK.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................ 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V an Conversions/Campers ................. 6 䡵 V ehicle Identification Number .
INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it r epresents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5.
W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against proce- dures that could r esult in damage to your vehicle. If you do not read this entir e manual, you may miss important information.
NOTE: It is illegal to remove or alter the VIN. VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 2 ▫ W ireless Ignition Node (WIN) — If Equipped ......................... 1 2 ▫ K e y F O B ........................... 1 3 ▫ Removing Key FOB From Ignition .
▫ Remote Open W indow Feature — If Equipped ......................... 2 3 ▫ Using The Panic Alarm ................. 2 4 ▫ Programming Additional T ransmitters ...... 2 4 ▫ T ransmitter Battery Replacement .......... 2 4 ▫ General Information .
▫ Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbag ............................. 4 9 ▫ Airbag System Components .............. 5 1 ▫ Advanced Front Airbag Featur es .......... 5 1 ▫ Airbag Deployment Sensors And Controls .
A WORD ABOUT YOUR KEYS Key Fob with Remote Keyless Entry (RKE) — If Equipped Y our vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a W ireless Ignition Node (WIN) with integral ignition switch.
Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key , which stores in the r ear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
T o remove the emer gency key , slide the mechanical latch at the top of the Key Fob sideways with your thumb and then pull the key out with your other hand. NOTE: Y ou can insert the double-sided emergency key into the lock cylinder with either side up.
Information Center (EVIC) /Personal Settings (Customer- Programmable Featur es)” in “Understanding Y our In- strument Panel” for further information. W ARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
SENTR Y KEY 姞 The Sentry Key 威 Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regar dless of whether the vehicle is locked or unlocked.
All of the Key Fobs provided with your new vehicle have been programmed to the vehicle electr onics. Replacement Keys NOTE: Only Key Fobs that are pr ogrammed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle.
General Information The Sentry Key 威 system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interfer ence that may cause undes- ired operation.
NOTE: If the V ehicle Security Light stays on continu- ously during vehicle operation, have the system checked by an authorized dealer . T o Disarm the System Use the RKE transmitter to unlock the door .
• The illuminated entry system will not operate if the dimmer control is in the extr eme left position. REMOTE KEYLESS ENTR Y (RKE) — IF EQUIPPED The RKE system allows you to lock or unlock the doors and activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held radio transmitter with integrated key .
Remote Key Unlock, Driver Door/All Doors First This feature lets you pr ogram the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE transmitter .
Flash Lamps with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmit- ter .
Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter . This feature can be turned on or turned off.
Using the Panic Alarm T o turn the Panic Alarm featur e ON or OFF , press and hold the P ANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.
1. W ith the RKE transmitter buttons facing down, use a flat blade screwdriver to pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal. 2. Remove and replace the battery . A void touching the new battery with your fingers.
REMOTE ST ARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security .
Remote Start Abort Message on Electronic V ehicle Information Center (EVIC) — If Equipped The following messages will display in the EVIC if the vehicle fails to remote start or exits r emote start .
NOTE: T o avoid unintentional shut downs, the system will disable the one time press of the REMOTE ST AR T button for two seconds after receiving a valid Remote Start request.
DOOR LOCKS Manual Door Locks Front and r ear doors may be locked by moving the lock knob down or unlocked by moving the lock knob up. Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will r emain locked when closed.
Power Door Locks — If Equipped A power door LOCK switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door LOCK switch while the Key Fob is in the ignition, and any front door is open, the power locks will not operate.
• For vehicles not equipped with the EVIC, perform the following procedur e: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt. (Fastening the seat belt will cancel any chiming that may confuse you during this programming pr ocedure.
• For vehicles not equipped with the EVIC, perform the following procedur e: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt. (Fastening the seat belt will cancel any chimes that may be confusing during this programming pr ocedure.
T o use the system, open each rear door , use a flat blade screwdriver (or emer gency key) and rotate the dial to engage and disengage the Child-Protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
WINDOWS Power Windows – If Equipped The control on the left fr ont door panel has UP-DOWN switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window contr ol and on the rear doors of the Cr ew Cab models.
W ARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seri- ously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
rough r oad conditions may trigger the auto reverse function unexpectedly during auto closure. If this happens, pull the switch lightly to the first detent and hold to close the window manually .
Wind Buffeting W ind buffeting can be described as the per ception of pressur e on the ears or a helicopter-type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down or in partially open positions. This is a normal occurrence and can be minimized.
W ARNING! In an accident, you and your passengers can suffer much greater injuries if you are not properly buckled up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! (Continued) • Be sure everyone in your vehicle is in a seat and using a seat belt properly . • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of an accident best.
2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
W ARNING! • A belt buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly .
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in an accident.
W ARNING! A frayed or torn belt could rip apart in an accident and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
2. T o reattach the seat belt to the fr ont center seat, pull the black buckle latch plate forward fr om the cab back panel and insert it into the black keyed buckle until there is an audible “click”. For proper seatbelt usage, r efer “Lap/Shoulder Belt Operating Instructions”.
W ARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in an accident. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
Adjustable Upper Shoulder Belt Anchorage In the front r ow outboard seats, the shoulder belt can be adjusted upward or downwar d to help position the belt away from your neck. Pr ess the button located on the upper belt guide, and then move it up or down to the position that fits you best.
W ARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones.
Enhanced Seat Belt Use Reminder System (BeltAlert 姞 ) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the BeltAlert 威 will alert the driver to buckle the seat belt.
Seat Belts and Pregnant Women W e recommend that pr egnant women use seat belts throughout their pr egnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible.
mounted in the instrument panel, above the glove com- partment. The words SRS AIRBAG are embossed on the airbag covers. NOTE: These airbags are certified to the new Federal regulations for Advanced Airbags. The Advanced Front Airbags have a multistage inflator design.
Airbag System Components Y our vehicle may be equipped with the following airbag system components: • Occupant Restraint Controller (ORC) • Airbag W arning Light • Steering Wheel and Column • .
W ARNING! (Continued) • Do not put anything on or around the airbag covers or attempt to open them manually . Y ou may damage the airbags and you could be injured because the airbags may no longer be functional. The protective covers for the airbag cushions are designed to open only when the airbags are inflat- ing.
ride properly buckled up in the r ear seat. Never allow children to slide the shoulder belt behind them or under their arm. If a child from 1 to 12 years old (not in a r ear facing child seat) must ride in the front passenger seat, move the seat as far back as possible and use the proper child r estraint.
Airbag Deployment Sensors and Controls Occupant Restraint Controller (ORC) The ORC is part of a Federally regulated safety system requir ed for this vehicle.
The ORC contains a backup power supply system that may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. Also, the ORC turns on the Airbag W arning Light in the instrument panel for appr oxi- mately four to eight seconds for a self-check when the ignition is first turned on.
instrument panel separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in about 50 to 70 milliseconds. This is about half of the time it takes to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and fr ont passenger .
If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and fr ont passenger as the airbags deploy and unfold.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you.
Airbag W arning Light Y ou will want to have the airbags ready to inflate for your protection in a collision. The Airbag W arning Light monitors the internal circuits and inter connecting wiring associated with airbag system electrical components.
• Whether or not the driver and passenger safety belts were buckled/fastened; • How far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • How fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and injuries occur .
W ARNING! In an accident, an unrestrained child, even a tiny baby , can become a projectile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured.
children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year . These child seats are also held in the vehicle by the lap/shoulder belt. • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who ar e still too small to fit the vehicle’s seat belts properly .
Here are some tips for getting the most out of your child restraint: • Before buying any r estraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
W ARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in an accident. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Because the lower anchorages are to be intr oduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor - ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
W e urge you to car efully follow the directions of the manufacturer when installing your child r estraint. Many , but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector , and a means for adjusting the tension in the strap.
then allow the belt to retract into the r etractor . For additional information on ALR, refer to “Automatic Locking Mode”. T o install a child restraint, first, pull enough of the seat belt webbing from the r etractor to route it through the belt path of the child restraint and slide the latch plate into the buckle.
T ether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor dir ectly behind the seat.
Multiple Child Restraint Installation Sequence (Crew Cab — Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the r ear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly impr oved by raising the seat cushion to the “up” position.
Multiple Child Restraint Crew Cab 1 — Inner Anchor Strap Ring(s) 2 — Snap Hook 3 — T ether Strap 4 — Passenger’s Side Rear Child Seat 5 — Rear Center Child Seat 6 — Driver’s Side Rear .
Children T oo Large for Booster Seats Children who ar e large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat.
The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur . For the recommended viscosity and quality grades r efer to “Maintenance Procedur es” in “Maintaining Y our V e- hicle”.
Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
Front seat belt assemblies must be r eplaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor , torn webbing, etc.). If there is any question r egarding belt or retractor condition, r eplace the belt.
W ARNING! (Continued) • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and inter- fering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats.
Periodic Safety Checks Y ou Should Make Outside the V ehicle T ires Examine tires for excessive tr ead wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tr ead and sidewall for cuts and cracks.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 8 1 ▫ Inside Day/Night Mirror ................ 8 1 ▫ Automatic Dimming Mirror — If Equipped . . . 82 ▫ Outside Mirrors ...................... 8 2 ▫ Outside Mirrors Folding Featur e .
▫ General Information .................. 1 1 8 䡵 V oice Command — If Equipped ........... 1 1 8 ▫ V oice Command System Operation ........ 1 1 8 ▫ Commands ........................ 1 1 9 ▫ V oice T raining ...................... 1 2 2 䡵 Seats .
▫ Parking Lights And Panel Lights ......... 1 4 2 ▫ Fog Lights — If Equipped .............. 1 4 2 ▫ Interior Lights ...................... 1 4 3 ▫ Cargo Light ........................ 1 4 4 ▫ Lights-On Reminder .................. 1 4 4 ▫ Battery Saver .
䡵 Cigar Lighter And Ash Receiver — If Equipped .......................... 1 6 0 䡵 Power Inverter — If Equipped ............ 1 6 0 䡵 Cupholders .......................... 1 6 2 ▫ Front Instr ument Panel Cupholders — (40–20–40 Seats) .
MIRRORS Inside Day/Night Mirror Headlight glare can be r educed by moving the small control lever under the mirr or to the night position (lever flipped toward the r ear of vehicle). The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield).
Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glar e from vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light next to the button will illuminate to indicate when the dimming feature is activated.
W ARNING! V ehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
Power Mirrors — If Equipped The controls for the power mirr ors are located on the driver’s door trim panel. The power mirror contr ols consist of mirror select but- tons and a four-way mirr or control switch. T o adjust a mirror , press the mirr or select button for the mirror that you want to adjust.
Heated Mirrors — If Equipped These mirrors ar e heated to melt frost or ice. This feature is activated by pr essing the rear window defroster button. Illuminated V anity Mirror — If Equipped Illuminated vanity mirrors ar e located on each sun visor .
“Slide-On-Rod” Features of Sun Visor — If Equipped The sun visor “Slide-On-Rod” feature allows for addi- tional flexibility in positioning the visor to block out the sun. T o use the “Slide-On-Rod” feature, r otate the sun visor downward and unclip it.
T railer T owing Mirrors — If Equipped These mirrors ar e designed with an adjustable mirror head to provide a gr eater vision range when towing extra-wide loads. T o change position inboard or out- board, the mirr or head should be rotated (flipped in or out).
Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ Phone al- lows you to dial a phone number with your cellular phone using simple voice commands (e.g., “Call” ѧ “Mike” ѧ “W ork” or “Dial” ѧ “248-555-1212”).
linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages. W ARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use.
Operation V oice commands can be used to operate the Uconnect™ Phone and to navigate through the Uconnect™ Phone menu structur e. V oice commands are requir ed after most Uconnect™ Phone prompts. Y ou will be prompted for a specific command and then guided through the available options.
Cancel Command At any prompt, after the beep, you can say “Cancel” and you will be returned to the main menu. However , in a few instances the system will take you back to the previous menu.
phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority three and priority five phones are pr esent in the vehicle, the Uconnect™ Phone will use the priority three cellular phone when you make a call.
Add Names to Y our Uconnect™ Phonebook NOTE: Adding names to the Uconnect™ Phonebook is recommended when the vehicle is not in motion. • Press the button to begin. • After the “Ready” prompt and the following beep, say “Phonebook New Entry”.
• T o call a name from downloaded (or Uconnect™) Phonebook, follow the procedur e in “Call by Saying a Name” section. • Automatic download and update, if supported, begins as soon as the Bluetooth 威 wireless phone connection is made to the Uconnect™ Phone, for example, after you start the vehicle.
Object Exchange Profile (OBEX). Please see your phone Owner’s Manual for specific instructions on how to send these entries from your phone. NOTE: • The phone handset must support Bluetooth 威 OBEX transfers of phonebook entries to use this feature.
After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “Phonebook Edit” can be used to add another phone number to a name entry that already exists in the phonebook.
Delete/Erase “All” Uconnect™ Phonebook Entries • Press the button to begin. • After the “Ready” prompt and the following beep, say “Phonebook Erase All”. • The Uconnect™ Phone will ask you to verify that you wish to delete all the entries from the phonebook.
Phone Call Features The following features can be accessed thr ough the Uconnect™ Phone if the feature(s) ar e available on your cellular service plan. For example, if your cellular service plan provides thr ee-way calling, this feature can be accessed through the Uconnect™ Phone.
in progr ess. T o go back to the first call, refer to “T oggling Between Calls” in this section. T o combine two calls, refer to “Conference Call” in this section. Place/Retrieve a Call From Hold T o put a call on hold, press the button until you hear a single beep.
• After the “Ready” prompt and the following beep, say “Redial”. • The Uconnect™ Phone will call the last number that was dialed from your cellular phone.
• Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every Uconnect™ Phone language change operation, only the language-specific 32-name phone- book is usable.
W ARNING! T o use your Uconnect™ Phone System in an emer- gency , your cellular phone must be: • turned on, • paired to the Uconnect™ System, • and have network coverage. T owing Assistance If you need towing assistance: • Press the button to begin.
W orking with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. Y ou can use your Uconnect™ Phone to access a voice mail system or an automated service, such as a paging service or automated customer service line.
Barge In - Overriding Prompts The “V oice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately .
NOTE: Certain brands of cellular phones do not send the dial ring to the Uconnect™ Phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progr ess.
phone and the Uconnect™ Phone, follow the instructions described in your cellular phone User’s Manual. List Paired Cellular Phone Names • Press the button to begin. • After the “Ready” prompt and the following beep, say “Setup Phone Pairing”.
Delete Uconnect™ Phone Paired Cellular Phones • Press the button to begin. • After the “Ready” prompt and the following beep, say “Setup Phone Pairing”.
best results, the V oice T raining session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedur e may be repeated with a new user . The system will adapt to the last trained voice only .
• fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, Fr ench, and Spanish ac- cents, the system may not always work for some.
• fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity , echo, and loudness to a large degr ee rely on the phone and network, and not the Uconnect™ Phone. • Echo at the phone far end can sometimes be reduced by lowering the in-vehicle audio volume.
Send Messages: Y ou can send messages using Uconnect™ Phone. T o send a new message: • Press the button. • After the “Ready” prompt and the following beep, say “SMS Send” or “Send Messages.” • Y ou can either say the message you wish to send or say “List Messages.
16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me T urn SMS Incoming Announcement ON/OFF T urning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming mes- sages. • Press the button.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 1 13.
1 14 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 1 15.
V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompt.
V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oic.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly appr oved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the V oice Command button, listen for the beep, and say your command. Pressing the V oice Command button while the system is speaking is known as “barging in.
Changing the V olume 1. Start a dialogue by pressing the V oice Command button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the V oice Command system is speaking. Please note the volume setting for V oice Command is different than the audio system.
• “Previous Station” (to select the pr evious station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Satellite Radio T o switch to satellite radio mode, say “Sat” or “Satellite Radio”.
− “Continue” (to continue recor ding) − “Delete” (to delete the recor ding) • “Play Memos” (to play previously r ecorded memos) — During the playback you may press the V oice Command button to stop playing memos.
1. Press the V oice Command button, say “System Setup” and once you are in that menu then say “V oice T raining.” This will train your own voice to the system and will improve r ecognition. 2. Repeat the words and phrases when pr ompted by Uconnect™ V oice.
position, then release the handle to lock the seat into position. Using body pressur e, move forward and rear - ward on the seat to be sur e that the seat adjusters have latched. W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
W ARNING! • Actuating the recliner handle will allow the seat- back to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury . This dump feature allows access to the storage bin behind the seat.
W ARNING! (Continued) • Y ou can be seriously , even fatally , injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you.
Rear Head Restraints The outboard head r estraints can be adjusted. T o raise the head restraint, pull upwar d on the head restraint. T o lower the head restraint, pr ess the large button, located on the base of the head restraint, and push downwar d on the head restraint.
There ar e two power seat switches that are used to control the movement of the seat cushion and the seat- back. Adjusting the sear forward or rearward The seat can be adjusted both forward and r earward. Push the seat switch forward or r earward, the seat will move in the direction of the switch.
Reclining the seatback The angle of the seatback can be adjusted forward or rearwar d. Push the seatback switch forward or rearwar d, the seat will move in the direction of the switch. Release the switch when you have reached the desir ed position. W ARNING! • Adjusting a seat while driving may be dangerous.
Power Lumbar — If Equipped V ehicles equipped with power driver or passenger seats may be also be equipped with power lumbar . The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to incr ease the lumbar support.
W ARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.
The heated seats switch from HIGH to LOW and fr om LOW to OFF automatically , based on time and tempera- ture of the seat. The heated seats can operate on HIGH heat for as little as 4 minutes and up to 30 minutes before switching to LOW heat.
NOTE: • Once a heat setting is selected, heat will be felt within two to five minutes. • The engine must be running for the heated seats to operate. The heated seats switch from HIGH to LOW and fr om LOW to OFF automatically , based on time and tempera- ture of the seat.
V ehicles Equipped with Remote Start On models equipped with remote start, the drivers ventilated seat can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Y our V ehicle” for further information.
Keyless Entry (RKE) transmitters can also be pro- grammed to recall the same positions when the UN- LOCK button is pressed. NOTE: The power lumbar option is not programmable with driver memory seats. Y our vehicle was delivered with two RKE transmitters.
performed within 10 seconds if you desire to also use a RKE transmitter to recall memory positions. 8. T urn the ignition OFF and remove the key . 9. Press and r elease the LOCK button on one of the RKE transmitters.
T o Disable a RKE T ransmitter Linked to Memory 1. T urn the ignition switch to the OFF position and remove the key . 2. Press and r elease the memory SET button located on the driver’s seat. 3. W ithin 10 seconds, press and release the UNLOCK button on the RKE transmitter .
Driver Easy Exit and Easy Entry Control This additional feature pr ovides automatic driver’s seat positioning which will enhance driver mobility into and out of the vehicle. The seat cushion will move rearwar d approximately 2.5 in (60 mm) when the key is r emoved from the ignition switch.
2. Reach into the opening beneath the center of the hood and push the safety latch lever from right to left to r elease it, before raising the hood. CAUTION! T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage.
LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The head- light switch controls the operation of the headlights, parking lights, instrument panel lights, car go lights and fog lights (if equipped).
Headlights T o turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights ar e also turned on. T o turn off the headlights, r otate the headlight switch back to the O (Off) position.
Headlight Delay T o aid in your exit, your vehicle is equipped with a headlight delay that will leave the headlights on for approximately 90 seconds. This delay is initiated when the ignition is turned OFF while the headlight switch is on, and then the headlight switch is cycled off.
illuminate when the fog lights are on. The fog lights will turn off when the switch is pushed a second time, when the headlight switch is rotated to the of f position, or the high beam is selected.
Cargo Light The cargo lights ar e turned on by pressing on the cargo button. The cargo lights will also turn on for appr oximately 30 seconds when a RKE transmitter UNLOCK button is pressed, as part of the Illuminated Entry featur e.
Daytime Running Lights — If Equipped The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except P ARK. This provides a constant ⬙ Lights ON ⬙ condition until the ignition is turned OFF . The lights illuminate at less than 50% of normal intensity .
Lane Change Assist T ap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn of f. Flash-T o-Pass Y ou can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer - ing wheel.
Intermittent W iper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the contr ol knob into the upper end of the delay range.
T o prevent fr eeze-up of your windshield washer system in cold weather , select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. W ARNING! Sudden loss of visibility through the windshield could lead to an accident.
W ARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle.
The adjustable pedal switch is located to the left side of the steering column. Adjustment 1. Position the driver’s seat so that you are at least 10 in (25.4 cm) away from the airbag, located in the center of the steering wheel. 2. Fasten and adjust the seatbelts.
W ARNING! Do not adjust the pedals while the vehicle is moving. Y ou could lose control and have an accident. Always adjust the pedals while the vehicle is parked. HEA TED STEERING WHEEL — IF EQUIPPED The steering wheel contains a heating element that helps warm your hands in cold weather .
W ARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, ex- haustion, or other physical conditions must exer- cise care when using the steering wheel heater .
T o Activate Push the ON/OFF button (located in the end of the lever) once and the cruise indicator light (located in the mes- sage window of the cluster) will illuminate showing that the Electronic Speed Contr ol system is on.
V arying The Speed Setting When the Electronic Speed Contr ol is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever . If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is r eleased, then the new set speed will be established.
W ARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Y our ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy , snow-covered or slippery .
(RKE) transmitter , if equipped. These lights are also operated individually as reading lights by pr essing on the corresponding lens. NOTE: The courtesy/reading lights will r emain on until the switch is pressed a second time, so be sur e they have been turned off befor e leaving the vehicle.
ELECTRICAL POWER OUTLETS The auxiliary 12 V olt (13 Amp) power outlets can pr ovide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 V olt power outlets have a cap attached to the outlet indicating “12V DC”, together with either a key symbol or a battery symbol.
• Inside the upper lid of the center storage compartment — if equipped. • Rear of the center console storage compartment — Crew Cab. The key symbol indicates that this outlet can supply power when the key is in the ON or ACC positions.
W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter ar e available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver . For vehicles equipped with a floor console the cuphold- ers may be used.
T o avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter . The power inverter switch is located on the switch bank below the Climate Controls. T o turn on the power outlet, press the switch once. Pr ess the switch a second time to turn the power outlet off.
W ARNING! T o avoid serious injury or death: • Do not use a three-prong adapter . • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure.
Front Instrument Panel Cupholders — Floor Storage Bin For vehicles equipped with bucket seats two cupholders are located in the floor storage bin. Rear Cupholder — Crew Cab Crew Cab vehicles ar e equipped with rear cupholders located in the center armrest.
STORAGE Glove Box Storage The glove box is located on the passenger side of the instrument panel and featur es both an upper (if equipped) and lower storage area. T o open the upper glove box push upward on the handle release. The glove box door will automatically open.
T o open the lower glove box, pull on the handle to release the latch and lower the door . Door Storage Front Door Storage — If Equipped Storage areas and bottle holders (drivers side only) ar e located in the door trim panels.
Rear Door Storage — Crew Cab Storage compartments are located in both the driver and passenger door trim panels. Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armr est and contains both and upper and lower storage area.
W ARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. • In an accident, the latch may open if the total weight of the items stored exceeds about 10 lbs (4.
W ith the upper lid closed, pull on the lower handle to open the lower storage bin. Seatback Storage Located in the back of both the driver and passenger front seats ar e pockets that can be used for storage.
Storage (Regular Cab) The storage bin is located behind the front seats and r uns the length of the cab. Storage and Seats (Crew Cab) The Crew Cab models pr ovide additional storage under the rear seats. Lift the seats to access the storage com- partment.
CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids. Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the seats.
REAR WINDOW FEA TURES Rear Window Defroster The rear window defr oster button is located on the climate control panel. Pr ess this button to turn on the rear window defr oster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defr oster is on.
Power Sliding Rear Window — If Equipped The switch for the power sliding rear window is located on the overhead console. Pr ess the left side of the switch to open the glass and the right side of the switch to close the glass.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Featur es ............... 1 7 6 䡵 Instrument Cluster — Base ............... 1 7 7 䡵 Instrument Cluster — Pr emium ........... 1 7 8 䡵 Instrument Cluster Descriptions .......
䡵 Media Center 730N/430/430N (RER/RBZ/ RHB) CD/DVD/HDD/NA V — If Equipped . . . 210 ▫ Operating Instructions (V oice Command System) — If Equipped ................ 2 1 0 ▫ Operating Instructions (Uconnect™ Phone) — If Equipped ..........
䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/RER/RES Radios Only) .... 2 4 0 ▫ System Activation .................... 2 4 0 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) ......... 2 4 1 ▫ Selecting Uconnect™ Multimedia (Satellite) Mode .
INSTRUMENT P ANEL FEA TURES 1 — Headlight Switch 7 — 1 15v Power Inverter Outlet 13 — T ransfer Case Position Switch 2 — Instrument Cluster 8 — Power Outlet 14 — Ignition Switch 3 — Radi.
INSTRUMENT CLUSTER — BASE 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 177.
INSTRUMENT CLUSTER — PREMIUM 178 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTIONS 1. T achometer The T achometer indicates engine speed in revolutions per minute. CAUTION! Do not operate the engine with the tachometer pointer at high RPM for extended periods.
CAUTION! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the P ARK position, the light should turn off.
10. TOW/HAUL The TOW HAUL button is located on the center stack switch bank. This light will illumi- nate when TOW HAUL mode is selected 1 1. V ehicle Security Light — If Equipped This light will fl.
service, so that you can be sure that it is pr operly reset, or that the door jamb sticker is accurate if the odometer must be reset at zer o. The two trip odometers show individual trip mileage. T o switch from odometer to trip odometers, pr ess and release the TRIP ODOMETER button.
the TRIP button to turn of f the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL).
NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary r epeat this procedure.
17. Low Fuel Light When the fuel level reaches appr oximately 3.0 gal (1 1.0 L) this light will turn on, and remain on until fuel is added. For vehicles equipped with a premium cluster this indi- cator will display in the Electronic V ehicle Information Center (EVIC).
21. Brake W arning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low , or that there is a pr oblem with the Anti-lock Brake System reservoir .
W ARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. Y ou could have an accident. Have the vehicle checked immediately . V ehicles equipped with the ABS, ar e also equipped with Electronic Brake For ce Distribution (EBD).
Center (EVIC). Refer to ”Electronic V ehicle Information Center (EVIC) — If Equipped” for further information. 23. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic (OBDII) system which monitors the emissions and engine control sys- tem.
W ARNING! A malfunctioning catalytic converter , as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc.
27. T ransmission T emperature W arning Light This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.
belt remains unbuckled, the seat belt r eminder light will flash or remain on continuously . Refer to “Occupant Restraints” in “Things T o Know Before Starting Y our V ehicle” for further information. 29. Charging System Light This light shows the status of the electrical charg- ing system.
NOTE: The compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass. This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
Steering wheel EVIC control button, as it appears on the left side of the steer- ing wheel. Press and r elease the UP button to scroll up- ward thr ough the main menus (DTE, mi/gal, System Info, Messages, Units, Setup) and sub menus. Press and r elease the DOWN button to scroll downward thr ough the main menus and sub menus.
Electronic V ehicle Information Center (EVIC) Displays When the appropriate conditions exist, the EVIC displays the following messages: • Left front turn signal lamp out • Right front turn signal .
• T urn Signal On • RKE Battery Low • LOW W ASHER FLUID • Oil Change Due > Dealer Info • Park Assist On • Park Assist Off • W arning Object Detected • Left Front T urn Signal Light .
• Memory System Unavailable — Seatbelt Buckled • Memory 1 Profile Recall • Memory 2 Profile Recall • Adjustable Pedals Unavailable — V ehicle in Reverse • Adjustable Pedals Unavailable .
• Electronic Speed Contr ol Light This light will turn on when the electronic speed control is ON. • Electronic Thr ottle Control (ETC) Light This light informs you of a problem with the Electronic Thr ottle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check.
shift the transmission into NEUTRAL and idle the ve- hicle. If the temperature r eading does not return to normal, turn the engine off immediately and call for service. Refer to “If Y our Engine Overheats” in “What T o Do In Emergencies” for mor e information.
scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position.
significant amount of fuel to the vehicle will turn off the ⬙ LOW FUEL ⬙ text and a new DTE value will display . EVIC A verage Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will r ead “RESET” or show dashes for two seconds.
T o Reset The Display Reset will only occur while a resettable function is being displayed. Press and r elease the ODOMETER/TRIP ODOMETER button once to clear the resettable function being displayed.
Compass / T emperature Display The compass readings indicate the dir ection the vehicle is facing. The EVIC will display one of eight compass readings and the outside temperatur e.
NOTE: A good calibration requir es a level surface and an environment fr ee from large metallic objects such as buildings, bridges, undergr ound cables, railroad tracks, etc.
1. T urn the ignition switch ON. 2. Press the UP or DOWN button until the System Setup (Customer-Pr ogrammable Features) menu is reached, then press the SELECT button. 3. Press the DOWN button until the “Compass V ariance” message is displayed in the EVIC, then press the SELECT button.
Use the UP or DOWN button to display one of the following choices. Select Language When in this display you may select one of five lan- guages for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the UP or DOWN button while in this display and scr oll through the language choices.
feature showing the system has been activated, or the check-mark is removed showing the system has been deactivated. Remote Unlock Sequence When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the RKE transmitter UNLOCK button.
Horn W ith Remote Lock When this feature is selected, a short horn sound will occur when the RKE transmitter LOCK button is pressed. This feature may be selected with or without the Flash Lamps with Lock feature.
Key-Off Power Delay When this feature is selected, the power window switches, radio, hands-free system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned OFF .
make your selection, press and r elease the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated.
MEDIA CENTER 130 (SALES CODE RES) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio.
SEEK Buttons Press and r elease the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
Push the rotary TUNE/SCROLL control knob a second time and MID will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a thir d time and TREBLE will display .
SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory . The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corr esponding button number will display .
If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1.
the current selection. Pr essing and holding the SEEK button will allow faster scrolling thr ough the tracks in CD and MP3 modes. TIME Button Press this button to change the display fr om a large CD playing time display to a small CD playing time display .
Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs r ecorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor - mally .
When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rate.
T o increase the speed of disc loading, it is r ecommended to use CD-R media and single-session discs. T o create a single-session disc, enable the “Disc at Once” option before writing to the disc.
MEDIA CENTER 130 WITH SA TELLITE RADIO (SALES CODE RES+RSC) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
SEEK Buttons Press and r elease the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Pr ess the TUNE/SCROLL contr ol knob to save time change.
Push the rotary TUNE/SCROLL control knob a second time and MID will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a thir d time and TREBLE will display .
Program T ype 16-Digit Character Display Information Inform Jazz Jazz News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc .
hours, press the TUNE/SCROLL control knob to set the minutes. The minutes will begin to blink. Adjust the minutes using the right side TUNE/SCROLL control knob. Pr ess the TUNE/SCROLL contr ol knob to save time change. AM/FM Button Press the button to select either AM or FM mode.
Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (C.
EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not r emoved, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF .
Press the SET/RND button a second time to stop Ran- dom Play . Notes On Playing MP3 Files The radio can play MP3 files; however , acceptable MP3 file recor ding media and formats are limited. When writing MP3 files, pay attention to the following restric- tions.
Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs.
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
Press and hold the INFO button again for thr ee seconds to return to ⬙ elapsed time ⬙ display . Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows.
radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account. For further information, call the toll-free number 888-539-7474, or visit the Sirius web site at www .
Reception Quality Satellite reception may be interr upted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle. • Dense tree coverage may interr upt reception in the form of short audio mutes.
R W/FF Pressing the R W (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arr ows. TUNE Control (Rotary) T urn the rotary TUNE/SCROLL control knob clockwise to increase or counter clockwise to decrease the channel.
selected within five seconds after pressing the SET but- ton, the channel will continue to play but will not be stored into pushbutton memory . Y ou may add a second channel to each pushbutton by repeating the above pr ocedure with this exception: Press the SET button twice and SET 2 will show in the display window .
UCI supports Mini, 4G, Photo, Nano, 5G iPod 威 and iPhone 威 devices. Some iPod 威 software versions may not fully support the UCI features. Please visit Apple’s website for software updates. NOTE: • If the radio has a USB port, connecting an iPod 威 to this port does not play the media.
• The iPod 威 can be controlled using the radio buttons to Play , Browse, and List the iPod 威 contents. • The iPod 威 battery charges when plugged into the UCI connector (if supported by the s.
jump to the previous track in the list; pr essing this button at any other time in the track, it will jump to the beginning of the track. Pressing the SEEK >> button during play mode, it will jump to the next track in the list. • While a track is playing, press the INFO button to see the associated metadata (artist, track title, album, etc.
the track detail on the radio display . Once the track to be played is highlighted on the radio display , press the TUNE contr ol knob to select and start playing the track. T urning the TUNE control knob fast will scroll thr ough the list faster . During fast scroll, a slight delay in updating the information on the radio display may be noticed.
• MUSIC TYPE button: The MUSIC TYPE button is another shortcut button to the genre listing on your iPod 威 . CAUTION! • Leaving the iPod 威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation or damage the device.
information, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www- .siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1.
bikes should be placed as far rearwar d as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interr upted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle.
INFO Button Pressing the INFO button will cycle the display informa- tion between Artist, Song T itle, and Composer (if avail- able). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song T itle all of the time (press and hold again to r eturn to normal display).
SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number . This number is used to activate, deactivate, or change the Sirius subscription.
STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a r ocker type switch with a pushbutton in the center .
The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pr e-set pushbuttons.
NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair , moisture or dew on the disc) oversized, or have protection encoding. T ry a known good disc before considering disc player service.
Manual Heating and Air Conditioning System The controls for the manual heating and air conditioning system in this vehicle consist of a series of outer rotary dials and inner push knobs. These comfort controls can be set to obtain desired interior conditions.
temperatures. Rotating the knob clockwise, into the r ed area, indicates warmer temperatur es. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C con- denser (located in front of the radiator), for an accumu- lation of dirt or insects.
Mix Mode Air is directed thr ough the floor , defr ost and side window demist outlets. This setting works best in cold or snowy conditions that requir e extra heat at the windshield. This setting is good for maintaining comfort, while reducing moistur e on the windshield.
• In cold or damp weather , the use of the Recirculation mode will cause windows to fog on the inside because of moisture buildup inside the vehicle. For maximum defogging, select the Outside Air position. • The A/C can be deselected manually without disturb- ing the mode control selection by pr essing the A/C button.
MAX A/C For maximum cooling, when MAX A/C is selected the A/C is turned on automatically and the air is recir cu- lated. NOTE: A/C cannot be deselected when in MAX A/C position.
Automatic Operation 1. Position the MODE control knob to the Auto position on the Automatic T emperature Contr ol (A TC) Panel. 2. Position the BLOWER control knob in the Auto posi- tion on the A TC Panel. 3. Next, adjust the temperature you would like the system to maintain by adjusting the driver and front passenger temperature buttons.
NOTE: • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to pr ovide comfort as quickly as possible. • The temperature can be displayed in U.S. or Metric units by selecting the US/M customer-pr ogrammable feature.
selected. This allows the front occupants to contr ol the volume of air circulated in the vehicle and cancel the Auto mode. The operator can also select the direction of the airflow by selecting one of the following positions. Panel Mode Air comes from the outlets in the instr ument panel.
The Air Conditioning (A/C) button allows the operator to manually activate or deactivate the air conditioning system. When in A/C mode and the A TC is set to a cool temperature, dehumidified air flows through the air outlets.
glycol antifreeze coolant and 50% water is r ecommended. Refer to “Maintenance Procedur es” in “Maintaining Y our V ehicle” for proper coolant selection.
Operating Tips 258 UNDERST ANDING YOUR INSTRUMENT P ANEL.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 2 6 3 ▫ Normal Starting ..................... 2 6 3 ▫ Automatic T ransmission ............... 2 6 3 ▫ If Engine Fails T o Start ................ 2 6 4 ▫ After Starting .
▫ Electronically Shifted T ransfer Case (Four-Position Switch) – If Equipped ....... 2 7 8 ▫ Shifting Procedur e ................... 2 8 2 䡵 Limited-Slip Differ ential ................. 2 8 4 䡵 Driving On Slippery Surfaces ............. 2 8 5 䡵 Driving Through W ater .
▫ Replacement T ires .................... 3 1 1 䡵 Supplemental T ire Pr essure Information — If Equipped .......................... 3 1 3 䡵 T ire Chains .......................... 3 1 3 䡵 Snow T ires .......................... 3 1 5 䡵 T ire Rotation Recommendations .
▫ T owing T ips ........................ 3 3 9 䡵 Snowplow .......................... 3 4 0 ▫ Before Plowing ...................... 3 4 1 ▫ Snowplow Prep Package Model A vailability ......................... 3 4 1 ▫ Over The Road Operation W ith Snowplow Attached .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15- second intervals. W aiting a few seconds between such intervals will protect the starter fr om overheating.
If Engine Fails T o Start If the engine fails to start after you have followed the “Normal Starting” procedur e, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded.
If the engine has been flooded, it may start to run, but not have enough power to continue running when the key fob is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor . Release the accelerator pedal and the key fob once the engine is running smoothly .
AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
W ARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into P ARK, remove the key fob from the ignition, and apply the parking brake.
3. Firmly set the parking brake. 4. Press and maintain firm pr essure on the brake pedal. 5. Using the screwdriver or other suitable tool, pr ess and hold the override tab through the access port (ringed circle) on the bottom of the steering column. 6.
column shift lever down (-) or up (+) to select the desired top gear . For example, if the driver shifts the transmission into 3 (third gear), the transmission will never shift above third gear , but can shift down to 2 (second gear) or 1 (first gear), when needed.
the transmission and display 5 (ERS 5 is the same as normal fourth gear). Another tap down (-) will shift the transmission down to ERS 4 (direct gear). T o exit ERS mode, press and hold the top of the switch/ shift lever in the (+) direction until “D” is once again highlighted in the instrument cluster display .
W ARNING! • Never use the P ARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Y our vehicle could move and injure you and others if it is not completely in P ARK.
Overdrive Operation The Overdrive automatic transmission contains an elec- tronically contr olled fourth and fifth gear (Overdrive). The transmission will automatically shift from DRIVE to Overdrive i.
performance and reduce the potential for transmission overheating or failur e due to excessive shifting. When operating in the “TOW/HAUL” mode, fifth gear is disabled and 2-3 and 3-4 shift patterns are modified.
the upper gears. When the vehicle speed drops or during acceleration when the transmission downshifts to second gear , the clutch automatically disengages. NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant (antifreeze) ar e warm [usually after 1 to 3 miles (1.
• Four-wheel drive low range (4L) This transfer case is intended to be driven in the 2H position for normal street and highway conditions such as dry , hard surfaced roads.
Because four-wheel drive pr ovides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. NOTE: Delayed shifts out of four-wheel drive may be experienced due to uneven tire wear , low or uneven tire pressur es, excessive vehicle loading, or cold tempera- tures.
4L Four-Wheel Drive Low Range - This range locks the fr ont and rear driveshafts together for cing the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only . Do not exceed 25 mph (40 km/h).
method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). A void attempting to engage or disengage 4L with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h).
• Neutral (NEUTRAL) This electronically shifted transfer case is designed to be driven in the two-wheel drive position (2WD) for normal street and highway conditions on dry , hard surfaced roads.
If One Or More Shift Conditions Are Not Met: 1. The indicator light for the current position will r emain ON. 2. The newly selected position indicator light will con- tinue to flash.
Proper operation of four -wheel drive vehicles depends on tires of equal size, type and cir cumference on each wheel. Any difference in tir e size can cause damage to the transfer case. Because four-wheel drive pr ovides improved traction, there is a tendency to exceed safe turning and stopping speeds.
N Neutral - This range disengages both the front and r ear driveshafts from the powertrain. T o be used for flat towing behind another vehicle. Refer to “Recreational T owing” in Starting and Operating” for further information.
NOTE: The four-wheel drive system will not allow shifts between 2WD/4WD LOCK if the front and/or r ear wheels are spinning (no traction). In this situation, the selected position indicator light will flash and the origi- nal position indicator light will remain ON.
NOTE: • If Steps 1 or 2 of either the Preferr ed or Alternate Procedur e are not satisfied prior to attempting the shift, then the desired position indicator light will flash continuously while the original position indicator light is ON, until all requir ements have been met.
Care should be taken to avoid sudden accelerations when both rear wheels ar e on a slippery surface. This could cause both rear wheels to spin, and allow the vehicle to slide sideways on the crowned surface of a r oad or in a turn.
Flowing/Rising W ater W ARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water . Furthermore, flowing and/or rising water can carry your vehicle away swiftly .
CAUTION! (Continued) • Driving through standing water may cause dam- age to your vehicle’ s drivetrain components. Al- ways inspect your vehicle’ s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water .
POWER STEERING The standard power steering system will give you good vehicle response and incr eased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interr upted, it will still be possible to steer your vehicle.
Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not requir ed. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated.
The foot operated parking brake is located below the lower left corner of the instrument panel. T o apply the park brake, firmly push the park brake pedal fully .
The parking brake should always be applied whenever the driver is not in the vehicle. W ARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
BRAKE SYSTEM If power assist is lost for any reason (for example, repeated brake applications with the engine of f), the brakes will still function. However , you will experience a substantial increase in braking ef fort to stop the vehicle.
with a separate computer to modulate hydraulic pressur e to prevent wheel lockup and help avoid skidding on slippery surfaces. The system’s pump motor runs during an ABS stop to provide r egulated hydraulic pressure. The pump motor makes a low humming noise during operation.
W ARNING! (Continued) • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that af forded by the condition of the vehicle brakes and tires or the traction afforded.
NOTE: • P (Passenger) - Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light truck tir e based on U.
EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can ca.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Tire T erminology and Definitions T erm Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and r ear door (of a four-door vehicle) running from the sill to the r oof.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressure is listed on the driver’s side B-Pillar . T ire and Loading Information Placard T ire Placard Lo.
This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pr essures for the front, r ear , and spare tir es.
2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and pas- sengers from XXX lbs or XXX kg. 4. The resulting figur e equals the available amount of cargo and luggage load capacity .
5 ST ARTING AND OPERA TING 303.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement.
Inflation pressur es specified on the placard are always “cold tire inflation pr essure.” Cold tire inflation pr essure is defined as the tire pr essure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.
4500/5500 T ire Inflation 5 ST ARTING AND OPERA TING 307.
When adjusting inflation pressur e to a tire and wheel assembly mounted on a vehicle, use a Remote Mount Automatic Inflation Kit or see your authorized dealer .
Radial Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident result- ing in serious injury or death. Always use radial ply tires in sets of four (or six, in case of trucks with dual rear wheels).
T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves. They will appear as bands when the tr ead depth becomes 1/16 in (2 mm).
W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose control and have an accident resulting in serious injury or death.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
SUPPLEMENT AL TIRE PRESSURE INFORMA TION — IF EQUIPPED A light load vehicle condition is defined as two passen- gers [150 lbs (68 kg) each] plus 200 lbs (91 kg) of cargo. Cold tire inflation pr essures for a lightly loaded vehicle will be found on the face of the driver’s door .
CAUTION! (Continued) • Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower sug- gested operating speed of the chain manufacturer if different than the speed recommended by the manufacturer .
SNOW TIRES Snow tires should be of the same size and type constr uc- tion as the front tir es. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requir ement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressur es under any load condition.
Refer to “Maintenance Schedule” for the proper mainte- nance intervals. More fr equent rotation is permissible if desired. The r easons for any rapid or unusual wear should be corrected prior to r otation being performed.
T o check if tires ar e even, lay a straight edge across all four tires. The straight edge should touch all the tir es. CAUTION! 4500/5500 Dual Rear T ires have only one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the On/Off road tire.
Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the W orld- wide Fuel Charter , WWFC) to define fuel properties necessary to deliver enhanced emissions, performance and durability for your vehicle. W e recommend the use of gasolines that meet the WWFC specifications if they are available.
E-85 Usage In Non-Flex Fuel V ehicles Non-FFV vehicles are compatible with gasoline contain- ing 10% ethanol (E10). Gasoline with higher ethanol content may void the vehicle’s warranty .
allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline. Materials Added T o Fuel All gasolines sold in the United States are r equired to contain effective deter gent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost.
CAUTION! (Continued) • The use of fuel additives which are now being sold as octane enhancers is not recommended. Many of these products contain high concentra- tions of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer .
W ARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly . Until repaired, drive with all side windows fully open.
W ARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel to the vehicle when the engine is running. This is in violation of most state and federal fire regulations and may cause the MIL to turn on.
VEHICLE LOADING Certification Label As requir ed by National Highway T raffic Safety Admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar .
T ire Size The tire size on the Label r epresents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
Improper weight distributions can have an adverse ef fect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GA WR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles.
The recommended way to measur e GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross Combination W eight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.
that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. W eight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the truck.
Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin.
All trailer hitches should be professionally installed on your vehicle. T railer T owing Weights (Maximum T railer Weight Ratings) NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http:// www .
Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer • The weight of any other type of cargo or equipment put in or on your vehicle • The weight of the driver and all passengers.
W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
W ARNING! (Continued) 2. GTW 3. GA WR 4. T railer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). T owing Requirements – T ires • Do not attempt to tow a trailer while using a compact spare tir e.
• An electronically actuated trailer brake contr oller is requir ed when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electr onic brake controller is not r equired.
NOTE: This module has been designed and verified for electric trailer brakes. T o determine the type of brakes on your trailer , check with your trailer manufacturer or dealer . The user interface consists of the following: GAIN/ Brake Output Power Display Shows the current GAIN setting.
lever is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes. The trailer and the vehicle’s brake lamps will come on when either vehicle braking or manual trailer brakes are applied.
1. Make sure the trailer brakes ar e in good working condition, functioning normally , and properly adjusted. See your trailer dealer if necessary . 2. Hook up the trailer and make the electrical connec- tions according to the trailer manufactur er’s instructions.
CAUTION! The ITBM module has been designed and verified for electric trailer brakes. Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking.
W ARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automo- tive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury .
Electronic Speed Control – If Equipped − Do not use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops gr eater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency .
W ARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an acci- dent. Do not expect that the airbag will perform as described earlier in this manual CAUTION! The “Lamp Out” indicator could illuminate if exte- rior lamps are not properly installed.
The loaded vehicle weight, including the snowplow system, all aftermarket accessories, driver , passengers, options, and cargo, must not exceed either the Gr oss V ehicle W eight (GVWR) or Gross Axle W eight (GA WR) ratings. These weights are specified on the Safety Com- pliance Certification Label on the driver’s side door opening.
NOTE: During snowplow usage on vehicles equipped with outside temperature display , the display may show higher temperatures than the outside ambient tempera- ture. The higher displayed temperatur e is due to blocked or reduced airflow to the under hood ambient tempera- ture sensor caused by the snowplow .
RECREA TIONAL TOWING (BEHIND MOT ORHOME, ETC.) T owing This V ehicle Behind Another V ehicle T owing Condition Wheels OFF the Ground T wo-Wheel Drive Models Four-Wheel Drive Models Flat T ow NONE NOT .
Recreational T owing – T wo-Wheel Drive Models DO NOT flat tow this vehicle. Damage to the drivetrain will result. Recreational towing (for two-wheel drive models) is allowed ONL Y if the r ear wheels are OFF the ground. This may be accomplished using a tow dolly or vehicle trailer .
CAUTION! • Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. • T ow only in the forward direction. T owing this vehicle backwards can cause severe damage to the transfer case.
W ARNING! Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake.
12. Shift the transmission into P ARK or place manual transmission in gear (not in Neutral). CAUTION! Damage to the transmission may occur if the trans- mission is shifted into P ARK with the transfer case in Neutral (N) and the engine running.
7. Shift the automatic transmission into P ARK, or place manual transmission in Neutral. 8. Release the brake pedal. 9. Disconnect vehicle from the tow vehicle. 10. Start the engine. 1 1. Press and hold the brake pedal. 12. Release the parking brake. 13.
1. Bring the vehicle to a complete stop. Shift automatic transmission into P ARK. 2. T urn OFF the engine. 3. T urn the ignition switch to the ON/RUN position, but do not start the engine. 4. Press and hold the brake pedal. 5. Shift the automatic transmission into NEUTRAL or press the clutch pedal on a manual transmission.
CAUTION! Damage to the transmission may occur if the trans- mission is shifted into P ARK with the transfer case in NEUTRAL and the engine running. W ith the transfer case in NEUTRAL, ensure that the engine is OFF prior to shifting the transmission into P ARK.
Shifting Out of Neutral – Electronic Shift T ransfer Case (If Equipped) Use the following procedur e to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop, leaving it con- nected to the tow vehicle. 2. Firmly apply the parking brake.
15. Shift the transmission into gear , release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally . NOTE: • Steps 1 through 5 ar e requirements that must be met prior to pressing the transfer case NEUTRAL button and must continue to be met until the shift has been completed.
.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................ 3 5 6 䡵 Jacking And T ire Changing ............... 3 5 6 ▫ 3500 Models — If Equipped ............. 3 5 7 ▫ Preparations For Jacking ............... 3 5 8 ▫ Jacking Instructions .
HAZARD W ARNING FLASHER The Hazard W arning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the Hazar d W arning flasher . When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer gency .
3500 Models — If Equipped The jack and jack tools are stor ed under the front passenger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat. W ARNING! After using the jack and tools, always reinstall them in the original carrier and location.
Preparations For Jacking 1. Park the vehicle on a firm, level surface. A void ice or slippery areas. W ARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough of f the road to avoid the danger of being hit when operating the jack or changing the wheel.
W ARNING! (Continued) • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • T urn on the Hazard W arning flasher .
3. When changing the fr ont wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wr ench.
Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. NOTE: If the jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack.
7. Install wheel center cap (if equipped) and remove wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel. This may r esult in cap damage.
CAUTION! • Use a back and forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap; finish may occur . • The rear hub caps on the dual rear wheel has two pry off notches. Make sure that the hook of the jack handle driver is located squarely in the cap notch before attempting to pull off.
Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assem- bling the wheels for best access to the tire valve on the inner wheel. The tires of both dual wheels must be completely off the gr ound when tightening to insure wheel centering and maximum wheel clamping.
1. T ighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go thr ough the sequence a second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km).
Disc Wheels T ype Nut Stud Size T orque Ft Lbs T orque Newton Meters Cone 9/16-18 120-150 160-200 Flanged 9/16-18 130-160 190-220 T o Stow The Flat Or Spare — If Equipped Refer to Upfitters Body Builders Guide for information on stowing your spare tir e (if equipped).
CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 V olts or damage to the battery , starter motor , alternator or electrical system may occur . W ARNING! Do not attempt jump-starting if the battery is frozen.
W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. Y ou can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle.
8. Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery . 9. Disconnect the positive (+) end of the jumper cable from the positive (+) post of the dischar ged vehicle.
CAUTION! (Continued) • When “rocking” a stuck vehicle by moving be- tween 1st and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure.
W ARNING! • Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • Stand clear of vehicles when pulling with tow hooks. T ow straps and chains may break, causing serious injury . CAUTION! T ow hooks are for emergency use only to rescue a vehicle stranded off-road.
NOTE: The transfer case must be in the NEUTRAL position, and the transmission must be in P ARK (auto- matic transmission), or in gear (manual transmission) to tow a four-wheel drive vehicle, unless all its wheels ar e OFF the ground. The manufacturer r ecommends towing with all wheels OFF the ground.
.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 5.7L ............. 3 7 7 䡵 Onboard Diagnostic System (OBD II) ....... 3 7 8 ▫ Loose Fuel Filler Cap Message ........... 3 7 8 䡵 Emissions Inspection And Maintenance Programs .........
▫ Exhaust System ..................... 3 9 0 ▫ Cooling System ..................... 3 9 2 ▫ Brake System ....................... 3 9 8 ▫ Rear Axle And 4X4 Front Driving Axle Fluid Level ............................. 4 0 0 ▫ T ransfer Case ..
ENGINE COMP ARTMENT — 5.7L 1 — Air Cleaner Filter 7 — W asher Fluid Reservoir 2 — Automatic T ransmission Dipstick 8 — Integrated Power Module 3 — Engine Oil Fill 9 — Power Steering Flui.
ONBOARD DIAGNOSTIC SYSTEM (OBD II) Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
the SELECT button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL).
4. Approximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
your vehicle. Refer to these Service Manuals before attempting any procedur e yourself. NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle.
CAUTION! (Continued) • Y our vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air condi- tioning.
NOTE: Under no circumstances should oil change intervals exceed 8,000 miles (13 000 km) or six months, whichever occurs first. Engine Oil Selection For best performance and maximum protection under al.
Synthetic Engine Oils Y ou may use synthetic engine oils if the recommended oil quality requir ements are met and the recommended maintenance intervals for oil and filter changes are followed.
W ARNING! The air induction system (air cleaner , hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner , hoses, etc.) unless such removal is necessary for repair or maintenance.
W ARNING! (Continued) • Battery gas is flammable and explosive. Keep flame or sparks away from the battery . Do not use a booster battery or any other booster source with an output greater than 12 V olts. Do not allow cable clamps to touch each other .
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test.
NOTE: Use only manufacturer appr oved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compr es- sor Oil, or Refrigerants. Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluoro- carbon (HFC) that is endorsed by the Environmental Protection Agency (EP A) and is an ozone-saving product.
amount of a high quality lubricant such as MOP AR 威 Lock Cylinder Lubricant or equivalent directly into the lock cylinder . Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner .
The washer fluid reservoir will hold a full gallon of fluid when the Low W asher Fluid Light illuminates. W ARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
W ARNING! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, refer to “Safety T ips/Exhaust Gas” in “Things T o Know Before Starting Y our V ehicle” for further information.
Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is impor- tant to keep the engine properly tuned to assur e proper catalyst operation and prevent possible catalyst damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
Engine Coolant Checks Check the engine coolant (antifreeze) pr otection every 12 months (before the onset of fr eezing weather , where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fr esh coolant.
CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOA T engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection.
• Mix a minimum solution of 50% HOA T engine coolant and distilled water . Use higher concentrations (not to exceed 70%) if temperatures below ⫺ 34°F ( ⫺ 37°C) ar e anticipated. • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution.
W ARNING! (Continued) • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result. Disposal of Used Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance r equiring proper disposal.
normally a result of moistur e from rain, snow , or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator . If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven.
Brake System In order to assur e brake system performance, all brake system components should be inspected periodically . Refer to “Maintenance Schedule” for the proper mainte- nance intervals. W ARNING! Riding the brakes can lead to brake failure and possibly an accident.
W ARNING! • Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance.
W ARNING! (Continued) • Do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident. Rear Axle And 4x4 Front Driving Axle Fluid Level For models with 9.
Lubricant Selection Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further information. NOTE: The presence of water in the gear lubricant will result in corr osion and possible failure of differ ential components.
Automatic T ransmission Selection Of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor - mance. Use only the manufacturer ’s recommended trans- mission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Y our V ehicle” for further informa- tion.
transmission with an improper fluid level will gr eatly reduce the life of the transmission and of the fluid. Check the fluid level whenever the vehicle is serviced. Fluid Level Check – 545RFE Check the fluid level while the transmission is at normal operating temperature 82°C (180°F).
room temperatur e, it should be between the “HOT” (upper) refer ence holes when the transmission reaches 180°F (82°C). Remember it is best to check the level at the normal operating temperature. CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick.
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage.
• Use a high quality cleaner wax, such as MOP AR 威 Cleaner W ax or equivalent to remove r oad film, stains and to protect your paint finish. T ake care never to scratch the paint. • A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials ar e well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use MOP AR 威 T ouch Up Paint or equivalent on scratches as soon as possible.
• For grease stains, apply MOP AR 威 Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove stain. Use a fr esh, damp towel to remove soap residue. • Do not use any harsh solvents or any other form of protectants on Stain Repel pr oducts.
Plastic is not as scratch resistant as glass and ther efore differ ent lens cleaning procedures must be followed. T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing.
If the belts need cleaning, use a mild soap solution or lukewarm water . Do not remove the belts from the car to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly .
Cavity Cartridge Fuse Mini Fuse Description J03 25 Amp Natural Bat – Passenger Door Node J04 40 Amp Green Bat – ABS Pump J05 30 Amp Pink Bat – ABS V alve J06 30 Amp Pink Bat – H/Lamp W ash/ MT.
Cavity Cartridge Fuse Mini Fuse Description M19 5 Amp Ta n Ign R/ACC – Sunroof/W indow Sw Illum M20 25 Amp Natural Frt W iper M21 25 Amp Natural Door Locks M22 20 Amp Y ellow Fuel Pump M23 20 Amp Y .
Cavity Cartridge Fuse Mini Fuse Description M35 20 Amp Y ellow Htd Seat/Htd Str Wheel/Rear Htd Seat M36 20 Amp Y ellow Ign R-Rear Seat/Steer Wheel M37 10 Amp Red Horn #1 M38 20 Amp Y ellow IOD-CCN/Int.
Cavity Cartridge Fuse Mini Fuse Description M51 20 Amp Y ellow ASD #3 M52 10 Amp Red IGN R/S-SW A Y/ TCASE/DTCM/ F AD/TRLR BRAKE MOD. M53 15 Amp Blue IGN R/S-MFSW/ CNN/SCM/TPM/RR V iew M54 20 Amp Y el.
VEHICLE STORAGE If you are storing your vehicle for mor e than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw (IOD) fuse located in the Integrated Power Module, located in the engine compartment.
NOTE: For lighted switches, see your authorized dealer for replacement instr uctions. All of the inside bulbs are brass or glass-wedge base. Aluminum base bulbs are not appr oved. LIGHT BULBS – Exterior Bulb No. Center High Mounted Stop Lamp (CHMSL) .
7. Reach into the front wheel house ahead of the fr ont wheel, remove the fastener , and lift the cover over the access hole in the front of the wheel house splash shield.
10. Disconnect electrical connectors. 1 1. Replace bulb(s) as necessary . CAUTION! • Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • Always use the correct bulb size and type for replacement.
Center High-Mounted Stoplamp (CHMSL) With Cargo Lamp 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body . 3. T urn the desired bulb socket 1 ⁄ 4 turn and remove the socket and bulb from housing.
4. Pull the desired bulb straight fr om the socket. CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5.
2. Rotate the socket 1 ⁄ 4 turn and pull it from the lamp assembly . 3. Pull the bulb straight from it’s socket and r eplace. 7 MAINT AINING YOUR VEHICLE 421.
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) Standard Rear T ank 52 Gallons 197 Liters Optional Midship T ank 22 Gallons 83 Liters Engine Oil with Filter 5.7L Engine (SAE 5W -20, API Certified) 7 Quarts 6.6 Liters Cooling System 5.7L Engine (MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula) or equivalent.
FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 5–Y ear/100,000 Mile Formula HOA T (Hy- brid Organic Additive T echnology) or equivalent.
Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission (Five-Speed 545RFE) MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product. T ransfer Case MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance ...... 4 2 6 䡵 Maintenance Schedule .................. 4 2 6 ▫ 5.7L Gas Engine .
EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions contr ol system.
NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been 6 months since your last oil change even if the oil change indicator message is NOT illumi- nated. • Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time.
Once a Month • Check tire pr essure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of coolant reservoir , brake master cylinder , power steering and transmission and add as needed.
8,000 Miles (13,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 8,000 miles (13 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
24,000 Miles (39,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 24,000 miles (39 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
40,000 Miles (65,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 40,000 miles (65 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
56,000 Miles (91,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 56,000 miles (91 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
64,000 Miles (104,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 64,000 miles (104 000 km). ❏ Replace the engine air cleaner filter .
72,000 Miles (1 17,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 72,000 miles (1 17 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
88,000 Miles (147,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 88,000 miles (147 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
96,000 Miles (160,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 96,000 miles (160 000 km). ❏ Replace the engine air cleaner filter .
104,000 Miles (173,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 104,000 miles (173 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
120,000 Miles (199,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 120,000 miles (199 000 km). ❏ Lube the front drive shaft fitting (4x4 only).
128,000 Miles (212,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 128,000 miles (212 000 km). ❏ Replace the engine air cleaner filter .
144,000 Miles (238,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate the tires, rotate at the first sign of irregular wear , even if it occurs before 144,000 miles (238 000 km). ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
† This maintenance is recommended by the manufactur er to the owner , but is not required to maintain emissions warranty . W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 4 5 ▫ Prepar e For The Appointment ........... 4 4 5 ▫ Prepar e A List ...................... 4 4 5 ▫ Be Reasonable W ith Requests .
䡵 Publication Order Forms ................ 4 4 9 䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 5 1 ▫ T readwear ......................... 4 5 1 ▫ T raction Grades ..................... 4 5 1 ▫ T emperature Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its customer center .
W e appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you ar e absolutely delighted with the ownership experience. Y ou’ll be pleased with their sincere ef forts to resolve any warranty issues or related concerns.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may or der a recall and remedy campaign. However , NHTSA cannot become involved in individual problems between you, your authorized dealer , and the manufacturer .
LLC vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • Diagnostic Procedure Manuals Diagnostic Procedur e Manuals are filled with dia- grams, charts and detailed illustrations.
DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following tire grading categories wer e established by the National Highway T raffic Safety Administration. The specific grade rating assigned by the tire’s manufactur er in each category is shown on the sidewall of the tires on your vehicle.
T emperature Grades The temperature grades ar e A (the highest), B, and C, repr esenting the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10.
Adding Engine Coolant (Antifreeze) .......... 3 9 4 Adding Fuel ........................... 3 2 2 Adjustable Pedals ....................... 1 4 9 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 384 Air Conditioner Maintenance ............... 3 8 7 Air Conditioning .
Automatic T ransmission Adding Fluid ......................... 4 0 3 Fluid and Filter Changes ................. 4 0 4 Fluid Level Check ................... 402,403 Fluid T ype ........................ 402,424 Shifting ............................. 2 6 8 Special Additives .
Carbon Monoxide W arning ............... 73,321 Cargo Light ............................ 1 4 4 Cellular Phone ........................ 88,247 Center High Mounted Stop Light ............ 4 1 9 Center Lap Belts ......................... 4 6 Center Seat Storage Compartment .
Points to Remember .................... 3 9 6 Pressur e Cap ......................... 3 9 5 Radiator Cap ......................... 3 9 5 Selection of Coolant (Antifreeze) ......... 393,423 Cruise Contr ol (Speed Control) .............. 1 5 2 Cupholders .
T ow Hooks .......................... 3 7 1 T owing ............................. 3 7 2 Emission Control System Maintenance ...... 379,426 Engine ............................... 3 7 7 Air Cleaner .......................... 3 8 4 Block Heater .........
Fluid Level Checks Automatic T ransmission ................. 4 0 3 Brake .............................. 3 9 8 Power Steering ........................ 2 8 9 Fluids, Lubricants and Genuine Parts .......... 4 2 3 Fog Lights ....................... 142,190,418 Four Wheel Drive .
Guide, Body Builders ...................... 6 GVWR ............................... 3 2 4 Hands-Free Phone (Uconnect™) .............. 8 8 Hazard Driving Through Flowing, Rising, or Shallow Standing W ater ............... 2 8 5 Hazard W arning Flasher .
Instrument Panel and Contr ols .............. 1 7 6 Instrument Panel Lens Cleaning ............. 4 0 9 Integrated Power Module (Fuses) ............ 4 1 0 Integrated T railer Brake Controls ............. 3 3 4 Interior Appearance Care .................
C a r g o .............................. 1 4 4 Center Mounted Stop ................... 4 1 9 Check Engine (Malfunction Indicator) ........ 1 8 9 Courtesy/Reading ..................... 1 5 5 Daytime Running ...................... 1 4 5 Exterior .......
Maintenance Free Battery .................. 3 8 5 Maintenance Procedur es ................... 3 8 1 Maintenance Schedule .................... 4 2 6 Malfunction Indicator Light (Check Engine) ..... 3 7 9 Manual, Service ......................... 4 4 9 Manual T ransmission Fluid Level Check .
Identification Logo ..................... 3 8 3 Materials Added to ..................... 3 8 4 Pressur e Gauge ....................... 1 8 2 Recommendation ...................... 3 8 3 Synthetic ............................ 3 8 4 V iscosity ..........
Programming T ransmitters (Remote Keyless Entry) .................... 2 0 Radial Ply T ires ......................... 3 0 9 Radiator Cap (Coolant Pressur e Cap) ....... 393,395 Radio Operation ........................ 2 4 7 Radio, Satellite (Uconnect™ studios) .
Safety Information, T ire ................... 2 9 4 Safety T ips ............................. 7 2 Satellite Radio Antenna ................. 232,241 Satellite Radio (Uconnect™ studios) ........... 2 4 0 Schedule, Maintenance .................... 4 2 6 Seat Belt Maintenance .
T ransfer Case, Shifting out of T ransfer Case Neutral (N) ....................... 348,352 Shoulder Belt Upper Anchorage .............. 4 6 Shoulder Belts ........................... 3 8 Signals, T urn ...................... 76,145,179 Sliding Rear W indow Power .
T ip Start .............................. 2 6 3 T ire and Loading Information Placar d ...... 300,313 T ire Identification Number (TIN) ............. 2 9 8 T ire Markings .......................... 2 9 4 T ire Safety Information .................... 2 9 4 T i r e s .
Cooling System T ips .................... 3 4 0 Hitches ............................. 3 2 9 Minimum Requirements ................. 3 3 1 Mirrors .............................. 8 7 T railer and T ongue W eight ............... 3 3 0 W iring ............
W arning Lights (Instrument Cluster Description) ............. 1 7 9 W arnings and Cautions ..................... 6 W arranty Information ..................... 4 4 8 W ashers, W indshield .................. 147,389 W ashing V ehicle ..................
C HAS S I S CAB Chrysler Group LL C OWN ER’S MAN U AL 2011 2011 RAM TR UC K C HASS I S CAB 11DD43-126-AC Second Edition Printed in U.S.A. RAM TRUCK.
Ein wichtiger Punkt beim Kauf des Geräts Dodge 2011 Ram Truck Chassis Cab (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dodge 2011 Ram Truck Chassis Cab noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dodge 2011 Ram Truck Chassis Cab - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dodge 2011 Ram Truck Chassis Cab reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dodge 2011 Ram Truck Chassis Cab erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dodge 2011 Ram Truck Chassis Cab besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dodge 2011 Ram Truck Chassis Cab verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dodge 2011 Ram Truck Chassis Cab. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dodge 2011 Ram Truck Chassis Cab gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
