Benutzeranleitung / Produktwartung 2010 Charger SRT des Produzenten Dodge
Zur Seite of 442
OWNER’ S MANUAL 2010 Charger SRT.
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................ 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............
.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number .............. 6 䡵 V ehicle Modifications/Alterations .
INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it r epresents pr ecision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
1 INTRODUCTION 5.
W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against proce- dures that could r esult in damage to your vehicle. If you do not read this entir e manual, you may miss important information.
VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W or d About Y our Keys ................. 1 2 ▫ W ireless Ignition Node (WIN) ............ 1 2 ▫ K e y F O B ........................... 1 3 ▫ Removing Key FOB From Ignition ......... 1 3 ▫ Key-In-Ignition Reminder .
▫ Using The Panic Alarm ................. 2 1 ▫ Programming Additional T ransmitters ...... 2 1 ▫ T ransmitter Battery Replacement .......... 2 1 ▫ General Information ................... 2 2 䡵 Remote Starting System — If Equipped ....... 2 3 ▫ How T o Use Remote Start .
▫ Supplemental Restraint System (SRS) - Airbags ............................ 4 9 ▫ Airbag Deployment Sensors And Controls . . . 55 ▫ Event Data Recorder (EDR) .............. 6 2 ▫ Child Restraints ...................... 6 4 䡵 Engine Break-In Recommendations .
A WORD ABOUT YOUR KEYS The W ireless Ignition Node (WIN) operates similar to an ignition switch. It has four operating positions, three with detents and one that is spring-loaded. The detent posi- tions are LOCK, ACC, and ON. The ST ART position is a spring-loaded momentary contact position.
Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key , which stores in the r ear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead.
NOTE: • For vehicles not equipped with the Electronic V ehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for 10 minutes after the ignition switch is turned to the LOCK position.
NOTE: The Key-In-Ignition reminder only sounds when the Key Fob is placed in the LOCK or ACC ignition position. SENTR Y KEY 姞 The Sentry Key 威 Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated.
Replacement Keys NOTE: Only Key Fobs that are pr ogrammed to the vehicle electronics can be used to start and operate the vehicle. Once a Key Fob is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! • Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unat- tended.
• This device must accept any interference that may be received, including interfer ence that may cause undes- ired operation. VEHICLE SECURITY ALARM — IF EQUIPPED The V ehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau- thorized operation.
NOTE: • The driver’s door key cylinder and the trunk button on the RKE transmitter cannot arm or disarm the V ehicle Security Alarm. • The V ehicle Security Alarm r emains armed during trunk entry . Pressing the TRUNK button will not disarm the V ehicle Security Alarm.
The lights will fade to off after appr oximately 30 seconds or they will immediately fade to off once the ignition switch is turned ON from the LOCK position.
within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
T o Unlatch the T runk Press the TRUNK button on the RKE transmitter two times within five seconds to unlatch the trunk. Using the Panic Alarm T o turn the Panic Alarm featur e on or off, pr ess and hold the P ANIC button on the RKE transmitter for at least one second and release.
1. Battery access is through a door located on the rear of the Key Fob. Insert a small, flat blade screwdriver into the slot and gently pry open the access door . 2. Remove and replace the battery . A void touching the new battery with your fingers. Skin oils may cause battery deterioration.
If your RKE transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the transmitter . The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower , airport transmitter , and some mobile or CB radios.
W ARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Mon- oxide (CO) which is odorless and colorless. Car- bon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children.
T o Exit Remote Start Mode without Driving the V ehicle Press and r elease the REMOTE ST AR T button one time, or allow the engine to run for the entir e 15-minute cycle. NOTE: T o avoid unintentional shut downs, the system will disable the one time press of the REMOTE ST ART button for two seconds after receiving a valid Remote Start request.
DOOR LOCKS Manual Door Locks T o lock each door , push the door lock plunger on each door trim panel downward. T o unlock each door , pull the door lock plunger on each door trim panel upward. If the door lock plunger is down when you shut the door , the door will lock.
Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. If you press the power door LOCK switch while the Key Fob is in the ignition, and any front door is open, the power locks will not operate.
Automatic Door Locks Programming The Automatic Door Locks feature can be enabled or disabled as follows: • For vehicles equipped with the Electronic V ehicle Information Center (EVIC), refer to “E.
3. The transmission is in NEUTRAL or P ARK. 4. The driver door is opened. 5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h).
Child Protection Door Lock T o provide a safer environment for small childr en riding in the rear seats, the r ear doors are equipped with a Child Protection Door Lock system. T o Engage the Child Protection Door Lock System 1. Open the rear door . 2.
W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
3. Repeat Steps 1 and 2 for the opposite rear door . NOTE: After disengaging the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. WINDOWS Power Windows The window controls on the driver’s door contr ol all the door windows.
W ARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
T o close the window part way , lift the window switch to the first detent and release it when you want the window to stop. The power window switches will remain active for up to 60 minutes after the ignition switch is turned off. Open- ing either front door will cancel this featur e.
Reset Anytime the vehicle battery is disconnected or goes dead, the AUTO-up function will be disabled. T o reactivate the AUTO-up featur e, perform the following procedur e after vehicle power is restor ed: 1.
TRUNK LOCK AND RELEASE The trunk lid can be r eleased from inside the vehicle by pressing the TRUNK RELEASE button located on the instrument panel to the left of the steering wheel. NOTE: The transmission must be in P ARK before the button will operate.
TRUNK SAFETY W ARNING W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
• Advanced Front Airbags for driver and front passen- ger • Supplemental Side Airbag Inflatable Curtains (SABIC) for the driver and passengers seated next to a window — if equipped • An energy.
Buckle up even though you are an excellent driver , even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own str eet. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
W ARNING! (Continued) • W earing your belt in the wrong place could make your injuries in a collision much worse. Y ou might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your pas- sengers safe, too.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
W ARNING! (Continued) • A belt that is worn under your arm is dangerous. Y our body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury . A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones.
W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job properly .
Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the shoulder belt can be adjusted upward or downwar d to position the belt away from your neck. Push and fully depr ess the button above the webbing to release the anchorage, then move it up or down to the position that fits you best.
3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing. Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically pre- locked.
Seat Belt Pretensioners — If Equipped The seat belts for both front seating positions may be equipped with pretensioning devices that ar e designed to remove slack fr om the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
For front passenger seats equipped with BeltAlert, your vehicle is equipped to detect when it is occupied. The BeltAlert 威 warning system is not activated when the front passenger seat is unoccupied.
4. T urn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. BeltAlert 威 can be reactivated by r epeating this procedur e.
Supplemental Restraint System (SRS) - Airbags This vehicle has Advanced Front Airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s Advanced Front Air- bag is mounted in the center of the steering wheel.
The Advanced Fr ont Airbags have a multistage inflator design. This allows the airbag to have differ ent rates of inflation based on the severity and type of collision.
• Supplemental Side Airbag Inflatable Curtains (SABIC) • Front and Side Impact Sensors • Front Seat Belt Pr etensioners, Seat Belt Buckle Switch, and Seat T rack Position Sensors Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver and front passenger airbags.
Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags may offer side-impact and vehicle r ollover protection to fr ont and rear seat outboar d occupants in addition to that provided by the body str ucture.
The system includes side impact sensors adjacent to both front and r ear seat occupants that are calibrated to deploy the SABIC airbags during impacts that requir e airbag occupant protection.
W ARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger Advanced Front Airbag. An airbag deployment can cause severe injury or death to infants in that posi- tion.
If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center . Phone numbers are pr ovided under ⬙ If Y ou Need Assistance”. W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
Advanced Front Airbags ar e designed to provide addi- tional protection by supplementing the seat belts in certain frontal collisions depending on the severity and type of collision. Advanced Front Airbags are not ex- pected to reduce the risk of injury in r ear , side, or rollover collisions.
Also, the ORC turns on the Airbag W arning Light in the instrument panel for appr oxi- mately six to eight seconds for a self-check when the ignition is first turned on.
separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in about 50 to 70 milliseconds. This is about half of the time it takes to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and fr ont passenger .
Enhanced Accident Response System In the event of an impact causing airbag deployment, if the communication network remains intact, and the power remains intact, depending on the natur e of the event the ORC will determine whether to have the Enhanced Accident Response System perform the follow- ing functions: • Cut off fuel to the engine.
• As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-pr oduct of the process that generates the non-toxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat.
Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you.
Airbag W arning Light Y ou will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system immediately .
2. Under certain circumstances, EDR data may not be recor ded (e.g., loss of battery power). In conjunction with other data gathered during a com- plete accident investigation, the electronic data may.
3. Requested by police under a legal warrant. 4. Otherwise required by law . Data parameters that are r ecorded: • Diagnostic trouble code(s) and warning light status for electronically-contr olled .
There ar e differ ent sizes and types of restraints for children fr om newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the corr ect seat for your child. Use the restraint that is corr ect for your child.
seats used in the forward-facing dir ection are for childr en who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year . These child seats are also held in the vehicle by the lap/shoulder belt or the LA TCH child restraint anchorage system.
W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
LA TCH — Child Seat Anchorage System (Lower Anchors and T ether for CHildren) Y our vehicle’s rear seat is equipped with the child restraint anchorage system called LA TCH.
Installing the LA TCH-Compatible Child Restraint System W e urge you to follow the manufacturer’s dir ections carefully when installing your child r estraint. Not all child restraint systems will be installed as described her e. Again, carefully follow the installation instr uctions that are pr ovided with the child restraint system.
means of adjusting the tension in the strap. Forward- facing toddler restraints and some r ear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate fr om the buckle, turn the buckle around, and insert the latch plate into the buckle again.
2. Route the tether strap to provide the most dir ect path for the strap between the anchor and the child seat. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child r estraint manufacturer’s instr uc- tions.
The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur . For the recommended viscosity and quality grades r efer to “Maintenance Procedur es” in “Maintaining Y our V e- hicle”.
Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
Safety Checks Y ou Should Make Inside the V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Front seat belt assemblies must be r eplaced after a collision.
W ARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury . • Always make sure that floor mats are properly attached to the floor mat fasteners.
Periodic Safety Checks Y ou Should Make Outside the V ehicle T ires Examine tires for excessive tr ead wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tr ead and sidewall for cuts and cracks.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 8 3 ▫ Inside Day/Night Mirror ................ 8 3 ▫ Automatic Dimming Mirror — If Equipped . . . 84 ▫ Outside Mirrors ...................... 8 4 ▫ Outside Mirrors Folding Featur e — If Equipped .
䡵 V oice Command — If Equipped ........... 1 1 6 ▫ V oice Command System Operation ........ 1 1 6 ▫ Commands ........................ 1 1 8 ▫ V oice T raining ...................... 1 2 1 䡵 Seats .............................. 1 2 1 ▫ Power Seats .
▫ Overhead Console Map/Reading Lights .... 1 3 4 ▫ Interior Lights ...................... 1 3 5 䡵 W indshield W ipers And W ashers .......... 1 3 6 ▫ Intermittent W iper System .............. 1 3 7 ▫ W indshield W ashers .................. 1 3 7 ▫ Mist Feature .
▫ Security ........................... 1 5 1 ▫ T roubleshooting T ips .................. 1 5 1 ▫ General Information .................. 1 5 2 䡵 Power Sunroof — If Equipped ............ 1 5 2 ▫ Opening Sunroof — Expr ess ............ 1 5 3 ▫ Closing Sunroof — Expr ess .
MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the r ear window . Headlight glare can be r educed by moving the small control under the mirr or to the night position (toward the rear of the vehicle).
Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glar e from vehicles behind you. Y ou can turn the featur e on or off by pr essing the button at the base of the mirror . A light next to the button will illuminate to indicate when the dimming feature is activated.
W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
Power Mirrors The power mirror switch is located on the driver’s door trim panel, next to the power door lock switch. A r otary knob selects the left mirror , right mirror or off position. After selecting a mirror , move the knob in the same direction you want the mirr or to move.
Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is located on the sun visor . T o use the mirror , rotate the sun visor downwar d and swing the mirror cover upwar d. The light turns on automatically . Closing the mirror cover turns off the light.
For Uconnect™ customer support, visit the following websites: • www .chrysler .com/uconnect • www .dodge.com/uconnect • www .jeep.com/uconnect • or call 1–877–855–8400 Uconnect™ Phon.
Uconnect™ Phone Button Depending on the vehicle options, either the radio or the mirror will contain the two contr ol buttons (Uconnect™ Phone button) and (V oice Command button) that will en- able you to access the system. V oice Command Button Actual button location may vary with the ra- dio.
• For certain operations, compound commands can be used. For example, instead of saying ⬙ Setup ⬙ and then ⬙ Phone Pairing, ⬙ the following compound command can be said: ⬙ Setup Phone Pairing. ⬙ • For each feature explanation in this section, only the combined form of the voice command is given.
T o complete the pairing process, you will need to refer - ence your cellular phone Owner’s Manual. The Uconnect™ website may also provide detailed instr uc- tions for pairing. The following are general phone to Uconnect™ Phone pairing instructions: • Press the button to begin.
Dial by Saying a Number • Press the button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Dial. ⬙ • The system will prompt you to say the number you want to call. • For example, you can say ⬙ 234-567-8901 ⬙ . • The Uconnect™ Phone will confirm the phone number and then dial.
• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook New Entry . ⬙ • When prompted, say the name of the new entry . Use of long names helps the V oice Command and it is recom- mended. For example, say ⬙ Robert Smith ⬙ or ⬙ Robert ⬙ instead of ⬙ Bob.
• Automatic download and update, if supported, begins as soon as the Bluetooth 威 wireless phone connection is made to the Uconnect™ Phone, for example, after you start the vehicle. • A maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the Uconnect™ Phone.
NOTE: • The phone handset must support Bluetooth 威 OBEX transfers of phonebook entries to use this feature. • Some phones cannot send phonebook entries if they are alr eady connected to any system via Bluetooth 威 , and you may see a message on the phone display that the Bluetooth 威 link is busy .
After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙ Phonebook Edit ⬙ can be used to add another phone number to a name entry that already exists in the phonebook.
Delete/Erase “All” Uconnect™ Phonebook Entries • Press the button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Erase All. ⬙ • The Uconnect™ Phone will ask you to verify that you wish to delete all the entries from the phonebook.
Phone Call Features The following features can be accessed thr ough the Uconnect™ Phone if the feature(s) ar e available on your cellular service plan. For example, if your cellular service plan provides thr ee-way calling, this feature can be accessed through the Uconnect™ Phone.
in progr ess. T o go back to the first call, refer to ⬙ T oggling Between Calls ⬙ in this section. T o combine two calls, refer to ⬙ Conference Call ⬙ in this section. Place/Retrieve a Call From Hold T o put a call on hold, press the button until you hear a single beep.
• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Redial. ⬙ • The Uconnect™ Phone will call the last number that was dialed from your cellular phone.
• Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every Uconnect™ Phone language change operation, only the language-specific 32-name phone- book is usable.
• The Uconnect™ Phone does slightly lower your chances of successfully making a phone call as to that for the cellular phone directly . W ARNING! Y our phone must be turned on and paired to the Uc.
V oice Mail Calling T o learn how to access your voice mail, refer to ⬙ W orking with Automated Systems. ⬙ W orking with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system.
• Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In - Overriding Prompts The “V oice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately .
phone, the audio will be played through your vehicle’s audio system. The Uconnect™ Phone will work the same as if you dial the number using V oice Command. NOTE: Certain brands of cellular phones do not send the dial ring to the Uconnect™ Phone to play it on the vehicle audio system, so you will not hear it.
If you would like to connect or disconnect the Bluetooth 威 connection between a Uconnect™ Phone paired cellular phone and the Uconnect™ Phone, follow the instructions described in your cellular phone User’s Manual. List Paired Cellular Phone Names • Press the button to begin.
• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • At the next prompt, say ⬙ Delete ⬙ and follow the prompts. • Y ou can also press the button at any time while the list is being played, and then choose the phone you wish to delete.
T o restore the V oice Command system to factory default settings, enter the V oice T raining session via the above procedur e and follow the prompts. V oice Command • For best performance, adjust the rearview mirr or to provide at least 1 ⁄ 2 in (1 cm) gap between the overhead console (if equipped) and the mirror .
• Phonebook (Downloaded and Uconnect™ Phone Lo- cal) name recognition rate is optimized when the entries are not similar . • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zer o” not “eight hundred”. • Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero).
Bluetooth 威 Communication Link Cellular phones have been found to lose connection to the Uconnect™ Phone. When this happens, the connec- tion can generally be reestablished by switching the phone off/on. Y our cellular phone is recommended to remain in Bluetooth 威 ON mode.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 1 1 1.
1 12 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE.
3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 1 13.
V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompt.
V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oic.
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly appr oved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the V oice Command button, listen for the beep, and say your command. Pressing the V oice Command button while the system is speaking is known as “barging in.
Commands The V oice Command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the V olume 1. Start a dialogue by pressing the V oice Command button.
Radio FM T o switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the fr equency) • “Next Station” (to select t.
Memo T o switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to recor d a new memo) — During the recor ding, you may press the V oice Command button to stop recor ding.
NOTE: Keep in mind that you have to press the V oice Command button first and wait for the beep before speaking the “Bar ge In” commands. V oice T raining For users experiencing difficulty with the system r ecog- nizing their voice commands or numbers the Uconnect™ V oice “V oice T raining” feature may be used.
Power Seats The power seat switch is on the outboard side of the seat near the floor . Use this switch to move the driver’s seat up or down, forward or r earward, or to r ecline the seatback. The passenger’s seat will move up or down, forward or r earward.
Power Reclining Seats The recliner contr ol is located on the outboard side of the seat. W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
Lumbar Support This feature allows you to incr ease or decrease the amount of lumbar support. T urn the control lever for- ward to incr ease and rearwar d to decrease the desir ed amount of lumbar support. Head Restraints Head restraints can r educe the risk of injury in the event of a rear impact.
T o remove the head restraint, pull upwar d on the head restraint to its highest position, push in both buttons at the base of each head restraint r od, and simultaneously pull up on the head restraint.
NOTE: Ensure that the fr ont of the head restraint is facing toward the fr ont of the vehicle. W ARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.
W ARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, ex- haustion or other physical condition must exercise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods of time.
When the seatback is folded to the upright position, make sure it is latched by str ongly pulling on the top of the seatback above the seat strap. W ARNING! • Be certain that the seatback is securely locked into position.
TO OPEN AND CLOSE THE HOOD T wo latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood.
CAUTION! T o prevent possible damage, do not slam the hood to close it. Lower the hood, until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Rotate the headlight switch to the second detent for headlight, park light, and instrument panel light operation.
The Headlights On with W ipers feature can be enabled or disabled. Refer to “Electronic V ehicle Information Center (EVIC)/Customer-Pr ogrammable Features” in “Under - standing Y our Instrument Panel” for further information.
Fog Lights The front fog light switch is built into the head- light switch. T o activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. T o turn off the front fog lights, either press headlight switch again or turn of f the headlight switch.
T urn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the fr ont and rear turn signal lights. NOTE: • If either light remains on and does not flash, or ther e is a very fast flash rate, check for a defective outside light bulb.
Interior Lights The interior lights come on when a door is opened. T o protect the battery , the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or ar e on because a door is open.
Dome Light Position Rotate the dimmer control completely upwar d to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer contr ol is in this position. Interior Light Defeat (OFF) Rotate the dimmer control to the extr eme bottom OFF position.
Rotate the end of the multifunction lever to the first detent past the intermittent settings for low-speed wiper operation, or to the second detent past the intermittent settings for high-speed wiper operation. CAUTION! T urn the windshield wipers off when driving through an automatic car wash.
W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshield with the defroster before and during windshield washer use.
TIL T/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downwar d. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column.
ADJUST ABLE PEDALS — IF EQUIPPED The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows both the brake and accelerator pedal to move toward or away fr om the driver to provide impr oved position with the steering wheel.
• The pedals can be adjusted while driving. • The pedals cannot be adjusted when the transmission is in REVERSE or when the Electronic Speed Contr ol is on. CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls.
NOTE: In order to ensur e proper operation, the Elec- tronic Speed Contr ol System has been designed to shut down if multiple Speed Control functions ar e operated at the same time.
• The Electronic Speed Contr ol may not engage if a differ ent size tire is installed on one wheel, such as the compact spare tir e. T o Deactivate The system will disable Electronic Speed Contr ol without erasing the memory if you: • Softly tap the brake pedal.
T o decrease speed while Electronic Speed Contr ol is set, push down and hold the Electronic Speed Contr ol lever in SET DECEL. Release the Electronic Speed Contr ol lever when the desired speed is r eached, and a new set speed will be established. T apping the Electronic Speed Control lever to SET DE- CEL once will result in a 1 mph (1.
OVERHEAD CONSOLE The overhead console contains courtesy/r eading lights and storage for sunglasses. Universal Garage Door Opener (HomeLink 威 ) buttons and power sunroof switch may also be included, if equipped. Courtesy/Reading Lights At the forward end of the console ar e two courtesy/ reading lights.
GARAGE DOOR OPENER — IF EQUIPPED HomeLink 威 replaces up to thr ee remote contr ols (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink 威 unit operates off your vehicle’s battery .
W ARNING! • Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people, pets, or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards.
2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink 威 buttons while keeping the EVIC display in view . For optimal training, point the battery end of the hand- held transmitter away from the HomeLink 威 .
This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer .
Gate Operator/Canadian Programming Canadian radio-frequency laws r equire transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink 威 to pick up the signal during programming.
Reprogramming A Single HomeLink 姞 Button T o reprogram a channel that has been pr eviously trained, follow these steps: 1. Place the ignition in the RUN position. 2. Press and hold the desired HomeLink 威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.
General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2.
W ARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
sunroof will automatically r etract. Remove the obstruc- tion if this occurs. Next, press the power sunr oof switch forward and r elease to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) pr events closing, press the power sunr oof switch forward and hold for two seconds after the reversal occurs.
Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switch will r emain active for up to 60 minutes after the ignition switch is turned OFF . Opening either front door will cancel this featur e.
The 12 V olt power outlet next to the ash receiver tray has power available only when the ignition is in the ON or ACC positions. W ARNING! Do not place ashes inside the cubby bin located on the center console on vehicle’s not equipped with the ash receiver tray .
W ARNING! T o avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 V olt outlet. (Continued) W ARNING! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly .
Rear Seat Cupholders The rear seat cupholders ar e located in the center armrest between the rear seats. The cupholders ar e positioned forward in the armr est and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the r ear occupants elbows.
T wo separate storage compartments are also located underneath the armrest. The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also con- tains a 12 V olt power outlet and a molded-in coin holder (designed to hold various size coins).
When the seatback is folded to the upright position, make sure it is latched by str ongly pulling on the top of the seatback above the seat strap. W ARNING! • Be certain that the seatback is securely locked into position.
W ARNING! (Continued) • Place as much cargo as possible in front of the rear axle. T oo much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway . • Do not pile luggage or cargo higher than the top of the seatback.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Featur es ............... 1 6 6 䡵 Instrument Cluster .................... 1 6 7 䡵 Instrument Cluster Descriptions ........... 1 6 8 䡵 Electronic V ehicle Information Center (EVIC) .
▫ Operating Instructions — V oice Command System (VR) — If Equipped ............. 1 9 5 ▫ Operating Instructions — Uconnect™ Phone — If Equipped ...................... 1 9 5 ▫ Clock Setting Procedur e — RBZ Radio ..... 1 9 5 ▫ Clock Setting Procedur e — RER/REN Radio .
▫ Controlling The iPod 威 Using Radio Buttons ........................... 2 2 5 ▫ Play Mode ......................... 2 2 6 ▫ List Or Browse Mode ................. 2 2 7 䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/RER/RES Radios Only) .
INSTRUMENT P ANEL FEA TURES 1 — Air Outlet 7 — Climate Control 13 — Hood Release 2 — Instrument Cluster 8 — Heated Seat Switch* 14 — T runk Release Button 3 — Hazard Switch 9 — Power O.
INSTRUMENT CLUSTER 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 167.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. T rip Odometer Button Press this button to change the display fr om odometer to either of two trip odometer settings.
7. Electronic Throttle Contr ol (ETC) Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if ther e is a problem with the Elec- tronic Thr ottle Control (ETC) system.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to “Maintaining Y our V ehicle” and follow the warnings under the Cooling System Pressure Cap paragraph.
12. Electronic Stability Program (ESP) / T raction Control System (TCS) Indicator Light If this indicator light flashes during accelera- tion, ease up on the accelerator and apply as little throttle as possible. Adapt your speed and driving to the prevailing r oad conditions, and do not switch off the Electr onic Stability Program (ESP).
15. High Beam Light This light will turn on when the high beam headlights are ON. Push the multifunction lever away from the steering wheel to switch the headlights to high beam. 16. Seat Belt Reminder Light This light will turn on for five to eight seconds as a bulb check when the ignition switch is first turned ON.
for you to make a recor d of the odometer reading befor e the repair/service, so that you can be sur e that it is properly r eset, or that the door jamb sticker is accurate if the odometer must be reset at zer o. This display shows the Electronic V ehicle Information Center (EVIC) messages when the appropriate conditions exist.
the brake booster , the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a r eserve braking capac- ity in the event of a failure to a portion of the hydraulic system.
The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied.
maintain correct tir e pressur e, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pr essure telltale. Y our vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly .
23. Anti-Lock Brake (ABS) Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.
CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability . If the MIL is flashing, severe catalytic converter damage and power loss will soon occur . Immediate service is required.
This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the following: • System status • V.
Press the SCROLL button to scroll through T rip Functions, Performance Pages (if equipped), Uconnect™ gps (if equipped), System Status Messages, and Personal Settings (Customer- Programmable Featur es). The SCROLL button also functions as a remote sound system con- trol.
• Door(s) Ajar (with a single chime if vehicle is in motion) • T runk Ajar (with a single chime) • Oil Pressur e • Oil Change Required (with single chime) • Low W asher Fluid (with a single .
• Braking Distance (if equipped with Performance Pages) • 1/8 Mile (if equipped with Performance Pages) • 1/4 Mile (if equipped with Performance Pages) • Instantaneous G-Force (if equipped wit.
T rip Functions Press and r elease the MENU button until one of the following T rip Functions displays in the EVIC: • A verage Fuel Economy • Distance T o Empty • T rip A • T rip B • Elapsed T ime • Display Units of Measure in Press the SCROLL button to cycle through all the T rip Computer functions.
When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of ⬙ LOW FUEL. ⬙ This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the ⬙ LOW FUEL ⬙ text and a new DTE value will display .
Performance Pages — If Equipped W ARNING! Measurement of vehicle statistics with the Perfor- mance Pages is intended for off-highway or of f-road use only and should not be done on any public roadways. It is recommended that these features be used in a controlled environment and within the limits of the law .
• Dashes will display if the vehicle fails to reach 60 mph (100 km/h) in less then 10 seconds. • The time will continue to display until the FUNCTION SELECT button is pressed. • Pressing the FUNCTION SELECT button will clear the current r un time and display the vehicle’s best 0-60 mph (0-100 km/h) time.
1/8 Mile, 1/4 Mile When selected, this screen displays the time it takes the vehicle to travel 1/8 mile (1/4 mile) within 30 seconds and the vehicle’s speed when it reaches 1/8 mile (1/4 mile). • The feature will “r eady” when the vehicle is at 0 mph (0 km/h).
Digital Speedometer When selected, this screen displays vehicle speed and recor ds top speed. • Press and hold the FUNCTION SELECT button for three seconds to toggle between curr ent speed and top speed. • T o reset top speed, quickly press and r elease the FUNC- TION SELECT button when top speed is displayed.
Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually . When the vehicle is new , the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated.
NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Cell Phones, Lap- tops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor , and it may give false readings.
used to select an item, and the AUDIO MODE button can be used to return to the pr evious menu. When the Map display is active, pressing the FUNCTION SELECT but- ton will change the Navigation Unit Display to the Menu.
Personal Settings (Customer-Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in P ARK. Press and r elease the MENU button until Personal Set- tings displays in the EVIC. Use the SCROLL button to display one of the following choices.
Press is selected, you must pr ess the RKE UNLOCK button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE UNLOCK button.
“Delay T urning Headlights Off” When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. T o make your selection, press and release the FUNCTION SELECT button until “0,” “30,” “60,” or “90” appears.
“Display Units of Measure in” The EVIC, odometer , and Uconnect™ gps (if equipped) can be changed between English and Metric units of measure. T o make your selection, press and release the FUNCTION SELECT button until “ENGLISH” or “MET - RIC” appears.
3. T o move the hour forward, touch the scr een where the word “Hour” with the arr ow pointing upward is dis- played. T o move the hour backward, touch the screen where the wor d “Hour” with the arrow pointing down- ward is displayed.
Changing the T ime Zone 1. T urn on the radio. 2. T ouch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. T ouch the screen wher e the words “Set T ime Zone” are displayed. The time zone selection menu will appear on the screen.
4. T o move the hour forward, touch the scr een where the word “Hour” with the arr ow pointing upward is dis- played. T o move the hour backward, touch the screen where the wor d “Hour” with the arrow pointing down- ward is displayed.
T ouch the screen where the wor ds “Show T ime if Radio is Off” ar e displayed to change the current setting. Changing the T ime Zone 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed. 3. T ouch the screen wher e “User Clock” is displayed, the clock setting menu will appear on the screen.
Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Pr ess the TUNE/SCROLL control knob to save time change. 5. T o exit, press any button/knob, or wait five seconds. R W/FF Pressing the R W (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next fr equency in the direction of the arr ows.
Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. AM/FM Button Press the buttons to select either AM or FM mode. SET/RND Button — T o Set the Pushbutton Memory When you are r eceiving a station that you wish to commit to pushbutton memory , press the SET/RND button.
Operation Instructions — CD MODE For CD And MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (C.
EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not r emoved, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF .
SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play . This feature plays the selections on the compact disc in random order to pr ovide an interesting change of pace. Press the right SEEK button to move to the next ran- domly selected track.
• Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a three- character extension) • Level 2: 31 (including a separator ⬙ . ⬙ and a three- character extension) Multisession disc formats are supported by the radio.
Playlist files are not supported. MP3 Pr o files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
TIME Button (Auxiliary Mode) Press this button to change the display to time of day . The time of day will display for five seconds (when ignition is OFF). MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate.
Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic V olume Control The electronic volume contr ol turns continuously (360 degrees) in either dir ection without stopping.
If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped W ith Uconnect” message will display on the radio screen. TIME Button Press the TIME button to alternate display of the time and radio frequency .
TUNE Control T urn the rotary TUNE/SCROLL control knob clockwise to increase or counter clockwise to decrease the fr equency . Setting the T one, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display . T urn the TUNE/SCROLL control knob to the right or left to increase or decr ease the bass tones.
T oggle the MUSIC TYPE button to select the following format types: Program T ype 16-Digit Character Display No program type or un- defined None Adult Hits Adlt Hit Classical Classicl Classic Rock Cls.
By pressing the SEEK button when the Music T ype icon is displayed, the radio will be tuned to the next frequency station with the same selected Music T ype name.
Y ou may add a second station to each pushbutton by repeating the above pr ocedure with this exception: Pr ess the SET/RND button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory .
If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number , and index time in minutes and seconds. Play will begin at the start of track 1.
TIME Button Press this button to change the display fr om a large CD playing time display to a small CD playing time display . R W/FF Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased or R W or another CD button is pressed.
The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders.
rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.
LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob.
Uconnect™ Multimedia (Satellite Radio) — If Equipped Satellite radio uses direct satellite-to-r eceiver broadcast- ing technology to provide clear digital sound, coast to coast.
Sirius ID number will display . The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen. Selecting Uconnect™ Multimedia (Satellite) Mode Press the SA T button until ⬙ SA T ⬙ appears in the display .
SEEK Buttons Press and r elease the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it.
T oggle the MUSIC TYPE button again to select the music type. By pressing the SEEK button when the Music T ype function is active, the radio will be tuned to the next channel with the same selected Music T ype name.
Every time a preset button is used, a corr esponding button number will display . Button s1-6 These buttons tune the radio to the channels that you commit to pushbutton memory (12 Satellite stations). Operating Instructions - Uconnect™ Phone (If Equipped) Refer to “Uconnect™ Phone” in “Understanding The Features If Y our V ehicle”.
Connecting The iPod 姞 Use the provided connection cable to connect an iPod 威 to the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles).
Play Mode When switched to UCI mode, the iPod 威 automatically starts Play mode. In Play mode, use the following buttons on the radio faceplate to control the iPod 威 and display data: • Use the TUNE control knob to select the next or previous track.
• Pressing the REPEA T button will change the iPod 威 mode to repeat the curr ent playing track. • Press the SCAN button to use iPod 威 scan mode, which will play the first five seconds of each track in the current list and then forwar d to the next song.
• During all List modes, the iPod 威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backwards (counter-clockwise) to get to the track faster . • In List mode, the radio PRESET buttons are used as shortcuts to the following lists on the iPod 威 .
CAUTION! • Leaving the iPod 威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer ’ s guidelines. • Placing items on the iPod 威 , or connections to the iPod 威 in the vehicle, can cause damage to the device and/or to the connectors.
information, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www- .siriuscanada.ca for Canadian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1.
bikes should be placed as far rearwar d as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interr upted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle.
INFO Button Pressing the INFO button will cycle the display informa- tion between Artist, Song T itle, and Composer (if avail- able). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song T itle all of the time (press and hold again to return to normal display).
SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number . This number is used to activate, deactivate, or change the Sirius subscription.
KICKER 姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECT ABLE SURROUND (DSS) – IF EQUIPPED Y our vehicle is equipped with a state of the art audio amplifier that provides 5.1-channel surr ound sound from any stereo audio sour ce. A new feature of the KICKER 威 audio system offers the ability to choose surr ound sound for any audio source.
media sources (DVDs, V ideo CDs, or other video media supported by the radio). Some audio will sound better in DSS modes, others in Stereo mode. When in “Audio Surround” mode, balance is set auto- matically . Fader control is available to add more sur - round audio if desir ed.
• The LCD screen swings up fr om the rear of the armr est to allow the rear seat passenger(s) to view the display . NOTE: Close the armrest after the LCD scr een has been raised to its viewing position. • The touch screen radio and DVD player contr ols allow front seat operation for easy setup in the case of younger rear seat passengers.
• T wo wireless infrared headsets allow r ear seat passen- gers to listen to the same or individual audio sources. Audio/V ideo RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly fr om an MP3 player .
REMOTE SOUND SYSTEM CONTROLS The remote sound system contr ols are located on the surface of the steering wheel at the three and nine o’clock positions. V ehicles equipped with steering wheel-mounted buttons are also equipped with the Electr onic V ehicle Information Center (EVIC).
When the EVIC is in the Compass/T emp/ Audio screen, pr ess the FUNCTION SE- LECT button to operate various radio, me- dia, and Universal Customer Interface (UCI) functions (i.e., advance presets, se- lect next folder , jump to or start playing songs in playlists, etc.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
Operation of the system is quite simple. Begin by turning the mode control knob (on the right) to AUTO, and place the blower control knob (on the left) to either LO AUTO or HI AUTO.
NOTE: • The surface of the climate control panel and the top center of the instrument panel should be kept fr ee of debris due to the location of the climate control sensors. Mud on the windshield may also cause poor operation of this system. • Extended use of recir culation may cause the windows to fog.
4 UNDERST ANDING YOUR INSTRUMENT P ANEL 243.
The operator can override the AUT O mode setting to change airflow distribution by rotating the mode contr ol knob (on the right) to one of the following positions. • Defrost Air is directed to the windshield thr ough the outlets at the base of the windshield.
conditioning. An indicator in the button illuminates when manual compressor operation is selected. NOTE: T o control the air conditioning manually , the mode selector must be moved out of the AUTO position. • Recirculation Contr ol This button can be used to block out smoke, odors, dust, high humidity , or if rapid cooling is desired.
W inter Operation Use of the air Recirculation mode during W inter months is not recommended because it may cause window fogging. V acation Storage Anytime you store your vehicle, or keep it out of service (i.
Control Setting Suggestions for V arious W eather Conditions 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 247.
.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 2 5 3 ▫ Automatic T ransmission ............... 2 5 3 ▫ Normal Starting (T ip Start) ............. 2 5 4 ▫ Extreme Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) .....
▫ General Information .................. 2 6 5 䡵 Driving On Slippery Surfaces ............. 2 6 5 ▫ Acceleration ........................ 2 6 5 ▫ T raction ........................... 2 6 6 䡵 Driving Through W ater ................. 2 6 6 ▫ Flowing/Rising W ater .
䡵 T ires — General Information ............. 2 9 2 ▫ T ire Pressur e ....................... 2 9 2 ▫ T ire Inflation Pressur es ................ 2 9 3 ▫ T ire Pressur es For High Speed Operation . . . 295 ▫ Radial Ply T ires ..............
䡵 Adding Fuel ......................... 3 1 2 ▫ Fuel Filler Cap (Gas Cap) .............. 3 1 2 ▫ Loose Fuel Filler Cap Message ........... 3 1 4 䡵 V ehicle Loading ...................... 3 1 5 ▫ V ehicle Certification Label .............. 3 1 5 ▫ Gross V ehicle W eight Rating (GVWR) .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instr uct all other occupants to buckle their seat belts. W ARNING! Never leave children alone in a vehicle.
Normal Starting (Tip Start) NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Do not press the accelerator . Use the Fob with Integrated Key to briefly turn the ignition switch to the ST AR T position and release it as soon as the starter engages.
If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold W eather” proce- dures, it may be flooded. T o clear any excess fuel, push the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch to the ST AR T position and release it as soon as the starter engages.
AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
• Shift lever position • Accelerator position • V ehicle speed The gear shifting process is continuously adapted, de- pendent on the driving style, the driving situation, and the road characteristics.
W ARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into P ARK, remove the key fob from the ignition switch, and apply the parking brake.
Brake/T ransmission Interlock Manual Override There is an override for the BTSI that allows you to move the shift lever out of the P ARK position if an electrical system malfunction occurs (i.e., dead battery). T o access the override, remove the r ubber tray from the storage bin located to the right of the shift lever .
Five-Speed Automatic T ransmission Shifting from DRIVE to P ARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when moving the shift lever between these gears.
W ARNING! Never use the P ARK position as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage.
CAUTION! Coasting the vehicle or driving for any other reason with the shift lever in NEUTRAL can result in transmission damage. W ARNING! Do not coast in NEUTRAL and never turn of f the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
T emporary T ransmission Limp Home Mode The transmission is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the transmission will engage Limp Home Mode. If vehicle acceleration worsens, or the transmission no longer shifts, the transmission is most likely operating in the Limp Home Mode.
AUTOSTICK 姞 AutoStick 威 is a driver-interactive transmission that of fers manual gear shifting to provide you with mor e control of the vehicle. AutoStick 威 allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance.
one second. The transmission will now operate automati- cally , shifting between the five available gears. General Information • Y ou can start out in first or second gear . The system will ignore attempts to upshift at too low of a vehicle speed. • The transmission will automatically downshift to first gear when coming to a stop.
T raction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and r oad surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability . T o reduce this possibility , the following precau- tions should be observed: 1.
Shallow Standing W ater Although your vehicle is capable of driving through shallow standing water , consider the following Caution and W arning before doing so.
W ARNING! • Driving through standing water limits your vehi- cle’ s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water . • Driving through standing water limits your vehi- cle’ s braking capabilities, which increases stop- ping distances.
• Upon initial start-up in cold weather , the power steer- ing pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system.
W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. If necessary , add fluid to restore to the pr oper indicated level.
When the parking brake is applied with the ignition switch in the ON position, the “Brake W arning Light” in the instrument cluster will illuminate. NOTE: • When the parking brake is applied and the transmis- sion is placed in gear , the “Brake W arning Light” will flash.
W ARNING! (Continued) • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident. • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury .
Anti-Lock Brake System The Anti-Lock Brake System (ABS) provides incr eased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to pr event wheel lock-up.
W ARNING! • The Anti-Lock Brake System contains sophisti- cated electronic equipment that may be suscep- tible to interference caused by improperly in- stalled or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability .
All vehicle wheels and tires must be the same size and type and tires must be pr operly inflated to produce accurate signals for the computer . Anti-Lock Brake Light The “Anti-Lock Brake Light” monitors the anti- lock brake system.
ELECTRONIC BRAKE CONTROL SYSTEM Y our vehicle is equipped with an advanced electronic brake control system commonly r eferred to as ESP . This system includes the Anti-Lock Brake System (ABS), the T raction Control System (TCS), the Brake Assist System (BAS), and the Electronic Stability Pr ogram (ESP).
Brake Assist System (BAS) This system complements the ABS by optimizing the vehicle braking capability during emergency braking maneuvers. This system detects an emergency braking situation by sensing the rate and amount of brake appli- cation and then applies optimum pressur e to the brakes.
power may also be reduced to assist in counteracting the condition of oversteer or understeer and help the vehicle maintain the desired path. The ESP uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle.
The ESP system has thr ee available operating modes: ESP On This is the normal operating mode for the ESP . Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving situations. The ESP should only be turned OFF for specific r easons as noted in the following paragraphs.
stopped with the engine running. After five seconds, a chime will sound, the “ESP/TCS Indicator Light” will illuminate, and the ⬙ ESP OFF ⬙ message will display in the vehicle odometer . Press and r elease the TRIP ODOM- ETER button located on the instrument cluster to clear this message.
W ARNING! W ith the ESP switched OFF , the enhanced vehicle stability offered by ESP is unavailable. In an emer - gency evasive maneuver , the ESP system will not en- gage to assist in maintaining stability . The “Full Off” ESP mode is intended for off-highway or of f-road only .
NOTE: • The “ESP/TCS Indicator Light” and the “ESP/BAS Malfunction Indicator Light” will turn on momen- tarily each time the ignition switch is turned to the ON position. • Each time the ignition switch is turned to the ON position, the ESP System will be ON even if it was turned OFF previously .
NOTE: • P (Passenger) - Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light truck tir e based on U.
EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can ca.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Tire T erminology and Definitions T erm Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and r ear door (of a four-door vehicle) r unning from the sill to the r oof.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on the driver’s side B-Pillar . T ire and Loading Information Placard This placard te.
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]).
5 ST ARTING AND OPERA TING 291.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
W ARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread.
CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure.
Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tir e inflation pressur e is very important.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one.
Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread.
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
SNOW TIRES Some areas of the country r equire the use of snow tir es during the winter . Standard tir es are of the all season type and satisfy this requir ement as indicated by the M+S designation on the tire sidewall. If you need snow tires, select tir es equivalent in size and type to the original equipment tires.
Tire Rotation – Standard T ires The suggested rotation method is the “side-to-side” as shown in the following diagram. Tire Rotation – All Season Tires The suggested rotation method for vehicles equipped with all season tires is the “forwar d-cross” as shown in the following diagram.
TIRE PRESSURE MONITOR SYSTEM (TPMS) The T ire Pressur e Monitor System (TPMS) will warn the driver of a low tire pr essure based on the vehicle r ecom- mended cold placard pr essure. The tire pr essure will vary with temperatur e by about 1 psi (6.9 kPa) for every 12°F (6.
For example, your vehicle may have a recommended cold (parked for more than thr ee hours) placard pr essure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tir e pressur e is 27 psi (186 kPa), a temperature dr op to 20°F (-7°C) will decrease the tir e pressur e to approximately 26 psi (179 kPa).
NOTE: • The TPMS is not intended to replace normal tir e care and maintenance or to provide warning of a tir e failure or condition. • The TPMS should not be used as a tire pr essure gauge while adjusting your tire pr essure. • Driving on a significantly under-inflated tir e causes the tire to over heat and can lead to tire failur e.
• V arious TPMS messages, which display in the Elec- tronic V ehicle Information Center (EVIC), and • TPM T elltale Light. The matching full size spare wheel and tir e assembly (if equipped) has a TPM sensor . The full size spare can be used in place of any of the four road tir es.
turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS W arning If a system fault is detected, the TPM T elltale Light will flash on and off for 75 seconds and then r emain on solid.
If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the TPM T elltale Light will no longer flash, and the ⬙ CHECK TPM SYSTEM ⬙ message will no longer display , and a pressure value will display in place of the dashes.
2. If you install the compact spare tire in place of a r oad tire that has a pr essure below the low-pr essure warning limit, upon the next ignition switch cycle, the TPM T elltale Light will remain ON and a chime will sound. In addition, the graphic in the EVIC will still display a flashing pressur e value.
The TPM sensors are r egulated under one of the follow- ing licenses: United States ..................... KR5S120123 Canada ........................ 2671-S120123 FUEL REQUIREMENTS 6.
The manufacturer supports the use of r eformulated gaso- line. Properly blended r eformulated gasoline will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE.
T o fix a Non-FFV vehicle inadvertently fueled once with E85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to r eset the engine controller memory More extensive r epairs will be requir ed for prolonged exposure to E85 fuel.
Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law .
Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadly . Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill.
NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap door reinfor cement. CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
W ARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle.
VEHICLE LOADING The load carrying capacity of your vehicle is shown on the “V ehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. Do not exceed the specified Gross V ehicle W eight Rating (GVWR) or the Gross Axle W eight Rating (GA WR).
W ARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if either rating is exceeded. Y ou could lose control of the vehicle and have an accident.
NOTE: • Refer to the “V ehicle Certification Label” affixed to the rear of the driver’s door for your vehicle’s GVWR and GA WRs. • Refer to the “T ire Placard” for your vehicle’s pr oper tire pr essure. TRAILER TOWING T railer towing with this vehicle is not recommended.
.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................ 3 2 0 䡵 If Y our Engine Overheats ................ 3 2 0 䡵 TIREFIT Kit ......................... 3 2 1 ▫ TIREFIT Storage ..................... 3 2 2 ▫ TIREFIT Kit Components And Operation .
HAZARD W ARNING FLASHER The Hazard W arning flasher switch is located in the switch bank near the top center of the instrument panel. Press the switch to turn on the Hazar d W arning flasher . When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer gency .
CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (1 16°C) or greater pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range 200– 230°F (93–1 10°C).
TIREFIT Storage The TIREFIT kit is located in the trunk. TIREFIT Kit Components and Operation 1. Sealant Bottle 2. Deflation Button — If Equipped 3. Pressure Gauge 4.
5. Mode Select Knob 6. Sealant Hose (Clear with Y ellow Cap) 7. Air Pump Hose (Black) 8. Power Plug Using the Mode Select Knob and Hoses Y our TIREFIT kit may be equipped with either of the following symbols to indicate the air or sealant mode. Selecting Air Mode T urn the Mode Select Knob (5) to this position for air pump operation only .
TIREFIT Usage Precautions • Replace the TIREFIT Sealant Bottle (1) and Sealant Hose (6) prior to the expiration date (printed on the bottle label) to assure optimum operation of the sys- tem. Refer to “Sealing a T ire with TIREFIT” section (F) “Sealant Bottle and Hose Replacement”.
W ARNING! (Continued) • Do not use TIREFIT or drive the vehicle under the following circumstances: − If the cut or puncture in the tire tread is approxi- mately 0.24 in. (6 mm) or larger . − If the tire has any sidewall damage. − If the tire has any damage from driving with extremely low tire pressure.
W ARNING! (Continued) • TIREFIT Sealant solution contains latex. In case of allergic reaction or rash, consult a physician im- mediately . Keep TIREFIT out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water .
3. Uncoil the Sealant Hose (6) and then remove the yellow cap from the fitting at the end of the hose. 4. Place the TIREFIT kit flat on the ground next to the deflated tire. 5. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose (6) onto the valve stem.
2. Connect the Power Plug (8) to a different 12 V olt power outlet in your vehicle or another vehicle, if avail- able. Make sure the engine is r unning before turning ON the TIREFIT kit. 3. The Sealant Bottle (1) may be empty due to previous use. Call for assistance.
If the tire inflates to the recommended pressure or is at least 26 psi (1.8 Bar) pressure within 15 minutes: 1. Press the Power Button (4) to turn off the TIREFIT kit. 2. Remove the Speed Limit sticker from the top of the Sealant Bottle (1) and place the sticker on the instrument panel.
W ARNING! TIREFIT is not a permanent flat tire repair . Have the tire inspected and repaired or replaced after using TIREFIT . Do not exceed 55 mph (88 km/h) until having the tire repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, and others around you.
5. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized dealer as soon as possible. Refer to “(F) Sealant Bottle and Hose Replacement.” NOTE: When having the tire serviced advise the autho- rized dealer or service center that the tire has been sealed using the TIREFIT service kit.
JUMP-ST ARTING PROCEDURES If your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done impr operly so please follow the procedur es in this section carefully .
Remote Battery Posts W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. Y ou can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
3. If using another vehicle to jump-start the battery , park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF . W ARNING! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result.
W ARNING! Do not connect the cable to the negative post (-) of the discharged battery . The resulting electrical spark could cause the battery to explode and could result in personal injury .
FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow , it can often be moved by a rocking motion. T urn your steering wheel right and left to clear the area ar ound the front wheels. Then shift back and forth between RE- VERSE and DRIVE.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone.
V ehicles equipped with A WD can be towed with the transmission in NEUTRAL and the rear wheels OFF the ground (or the r ear driveshaft removed) with no limita- tion on speed or distance. CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 6.1L ............. 3 4 1 䡵 Onboard Diagnostic System — OBD II ...... 3 4 2 ▫ Loose Fuel Filler Cap ................. 3 4 2 䡵 Emissions Inspection And Maintenance Programs ..........
▫ Cooling System ..................... 3 5 8 ▫ Brake System ....................... 3 6 3 ▫ Automatic T ransmission ............... 3 6 5 ▫ Rear Axle .......................... 3 6 7 ▫ Appearance Care And Protection Fr om Corrosion .........
ENGINE COMP ARTMENT — 6.1L 1 — Remote Jump Start (Positive Battery Post) 6 — Power Steering Fluid Reservoir 2 — Integrated Power Module 7 — Air Cleaner Filter 3 — Coolant Pressur e Cap 8 .
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
TRIP ODOMETER button to turn of f the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, impr operly installed, or damaged fuel filler cap may also turn on the MIL.
4. Approximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment.
Engine Oil Checking Oil Level T o assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New V ehicle Limited W arranty . Engine Oil V iscosity (SAE Grade) SAE 5W -40 engine oil is preferred for use in all operating temperatures.
Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil filter . Use a filter of this type for replacement. The quality of replacement filters varies considerably .
Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably . Only high quality filters should be used to assure most ef ficient service. MOP AR 威 engine air cleaner filters are a high quality filter and ar e recommended.
W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water .
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test.
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluor o- carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product.
2. Slide the lid on the filter adapter forward and down and remove the used filter . 3. Install the new filter with arrows pointing in the direction of airflow , which is toward the rear of the vehicle (text and arrows on the filter will indicate this).
Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- cated pe.
present please pr oceed to clean wiper blades with humid cloth removing any debris that may be af fecting its function. Adding W asher Fluid The windshield washer fluid reservoir is located in the front of the engine compartment. Be sur e to check the fluid level in the reservoir at r egular intervals.
have an authorized technician inspect the complete ex- haust system and adjacent body areas for br oken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
CAUTION! (Continued) • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly .
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position. The fan is tempera- ture controlled and can start at any time the ignition switch is in the ON position.
Cooling System – Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner . Follow with a thorough rinsing to remove all deposits and chemicals.
Adding Coolant Y our vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before replacement.
Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensur e that engine coolant (antifreeze) will r eturn to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
Coolant Level The coolant bottle provides a quick visual method for determining that the engine coolant (antifreeze) level is adequate. W ith the engine OFF and cold, the level of the engine coolant (antifreeze) in the bottle should be be- tween the ranges indicated on the bottle.
• If frequent engine coolant (antifr eeze) additions are requir ed, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressur e tested for leaks.
Master Cylinder – Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system fail- ure. Check the fluid level in the master cylinder when per- forming underhood services. Clean the top of the master cylinder area befor e removing the cap.
W ARNING! (Continued) • T o avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container . Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point.
CAUTION! • Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder . Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes.
Special Additives Automatic T ransmission Fluid (A TF) is an engineered product and its performance may be impair ed by supple- mental additives. Therefor e, do not add any fluid addi- tives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks.
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage.
• Use a high quality cleaner wax, such as MOP AR 威 Cleaner W ax to remove road film, stains and to pr otect your paint finish. T ake care never to scratch the paint. • A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials ar e well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use MOP AR 威 T ouch Up Paint or equivalent on scratches as soon as possible.
• Do not use any harsh solvents or any other form of protectants on Stain Repel pr oducts. Interior Care Use MOP AR 威 Fabric Cleaner or equivalent to clean fabric upholstery and MOP AR 威 Carpet Cleaner or equivalent for carpeting. Interior trim should be cleaned starting with a damp cloth, or MOP AR 威 Satin Select or equivalent.
T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
Replace the belts if they appear frayed or worn or if the buckles do not work properly . Cleaning the Center Console Cupholders Clean with a damp cloth or towel using a mild detergent with the cupholder in the center console. NOTE: The cupholder cannot be removed.
CAUTION! • When installing the integrated power module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure.
Cavity Car- tridge Fuse Mini- Fuse Description 8 — 30 Amp Green Starter 9 ——— 10 30 Amp Pink — W indshield W iper 1 1 30 Amp Pink — Anti-Lock Brake System (ABS) V alves 12 40 Amp Green —.
Rear Power Distribution Center There is also a power distribution center located in the trunk under the spar e tire access panel. This center contains fuses and relays.
CAUTION! • When installing the power distribution center cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure.
Cavity Car- tridge Fuse Mini- Fuse Description 5 30 Amp Pink — Heated Seats – If Equipped 6 — 20 Amp Y ellow Fuel Pump 7 — 20 Amp Y ellow Sub Amp – If Equipped 8 — 15 Amp Blue Diagnostic L.
Cavity Car- tridge Fuse Mini- Fuse Description 2 3——— 2 4——— 2 5——— 2 6——— 27 — 10 Amp Red Occupant Restraint Con- troller (ORC) 28 — 10 Amp Red Ignition Run 29 — 5 Amp O.
Cavity Car- tridge Fuse Mini- Fuse Description 38 — 10 Amp Red Cargo Light/Satellite Receiver (SDARS) V ideo – If Equipped/V ehicle Information Module – If Equipped 39 — 10 Amp Red Heated Mirr.
VEHICLE STORAGE If you are leaving your vehicle dormant for mor e than 21 days, you may want to take these steps to protect your battery . • Disconnect the negative cable from the battery . • Anytime you store your vehicle, or keep it out of service (i.
Exterior Bulb Number Low Beam Headlamp (Standard Halogen) ...... 9006 Low Beam Headlamp – High Intensity Discharge (HID) .............. D 1 S (Serviced at Authorized Dealer) High Beam Headlamp .................... 9005 Front Park/T urn Lamp ........
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Disconnect the bulb fr om the socket assembly and install the replacement bulb.
3 — Park/T urn Lamp Bulb 4 — Side Marker Lamp Bulb 384 MAINT AINING YOUR VEHICLE.
Low Beam Headlamp, High Beam Headlamp, and Park/T urn Lamp — Models with High Intensity Discharge Headlamps (HID) HID Headlamps The headlamps are a type of high voltage dischar ge tube. High voltage can remain in the cir cuit even with the headlamp switch off and the key r emoved.
Backup Lamp, Side Marker Lamp, T ail/T urn Lamp, and T ail/Stop Lamp 1. Open the trunk. 2. Remove two fasteners from the back of the taillamp assembly . 3. Pull back the trunk liner . 4. Remove the remaining fastener from the back of the taillamp assembly .
8. T urn the appropriate bulb and socket assembly coun- terclockwise to r emove it from the taillamp assembly . 1 — Backup Lamp Bulb 2 — Side Marker Lamp Bulb 7 MAINT AINING YOUR VEHICLE 387.
9. Disconnect the bulb fr om the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the taillamp assembly , and then turn it clockwise.
1 1. Reinstall the taillamp assembly , fasteners, electrical connector , and trunk liner . 12. Close the trunk. License Lamp 1. Remove the screws securing the lamp to the rear fascia. 2. Remove the bulb and socket assembly . 3. Disconnect the bulb fr om the socket assembly and install the replacement bulb.
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 19 Gallons 72 Liters Engine Oil with Filter 6.1 Liter Engine (SAE 5W -40, API Certified) 7 Quarts 6.6 Liters Cooling System * 6.1 Liter Engine (MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula or equivalent) 15.
FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hy- brid Organic Additive T echnology) or equivalent.
Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission MOP AR 威 A TF+4 威 Automatic T ransmission Fluid or equivalent licensed A TF+4 威 product. Brake Master Cylinder MOP AR 威 DOT 3 and SAE J1703 should be used or equivalent.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance ...... 3 9 4 䡵 Maintenance Schedule .................. 3 9 4 ▫ Required Maintenance Intervals .
EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions contr ol system.
NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time.
• Check the fluid levels of the coolant reservoir , brake master cylinder , and power steering, add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter . • Inspect the brake hoses and lines.
6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid.
30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid.
66,000 Miles (1 10,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Inspect and replace the PCV V alve if necessary .* ❏ Inspect the rear axle fluid.
102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the spark plugs.
1 14,000 Miles (190,000 km) or 1 14 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid.
138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter .
* This maintenance is recommended by the manufactur er to the owner , but is not requir ed to maintain emissions warranty . W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 4 1 3 ▫ Prepar e For The Appointment ........... 4 1 3 ▫ Prepar e A List ...................... 4 1 3 ▫ Be Reasonable W ith Requests .
䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 1 8 ▫ T readwear ......................... 4 1 9 ▫ T raction Grades .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty .
This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its customer center .
W e appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you ar e absolutely delighted with the ownership experience.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may or der a recall and r emedy campaign. However , NHTSA cannot become involved in individual problems between you, your authorized dealer , and the manufacturer .
• Diagnostic Procedure Manuals Diagnostic Procedur e Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer -controlled ve- hicle systems and features.
T readwear The T readwear grade is a comparative rating, based on the wear rate of the tire when tested under contr olled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
V ehicle Safety Standard No. 109. Grades B and A repr e- sent higher levels of performance on the laboratory test wheel, than the minimum requir ed by law . W ARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
INDEX 10.
About Y our Brakes .................... 270,272 ABS (Anti-Lock Brake System) ............ 273,276 Adding Engine Coolant (Antifreeze) .......... 3 6 0 Adding Fuel ........................... 3 1 2 Adding W asher Fluid ..................... 3 5 5 Additives, Fuel .
Automatic Door Locks ................... 27,28 Automatic Headlights .................... 1 3 1 Automatic T emperature Control (A TC) ......... 2 4 0 Automatic T ransaxle Special Additives ...................... 3 6 7 Automatic T ransmission ..........
Brightness, Interior Lights .................. 1 3 5 Bulb Replacement ..................... 381,382 Bulbs, Light .......................... 78,381 Calibration, Compass ..................... 1 8 9 Capacities, Fluid ........................ 3 9 0 Caps, Filler Fuel .
Console, Floor .......................... 1 5 9 Console, Overhead ....................... 1 4 5 Contract, Service ........................ 4 1 5 Coolant Pressur e Cap (Radiator Cap) .......... 3 6 1 Cooling System ......................... 3 5 8 Adding Coolant (Antifreeze) .
Door Locks ............................. 2 6 Door Locks, Automatic .................... 2 7 Door Opener , Garage ..................... 1 4 6 Driving On Slippery Surfaces ................... 2 6 5 Through Flowing, Rising, or Shallow Standing W ater ...
Fuel Requirements ..................... 3 0 8 Jump Starting ......................... 3 3 2 O i l ........................... 346,390,391 Oil Change Interval .................... 3 4 6 Oil Filler Cap ......................... 3 4 7 Oil Filter ........
Brake .............................. 3 6 4 Cooling System ....................... 3 5 8 Engine Oil ........................... 3 4 6 Power Steering ........................ 2 6 9 Fluids ................................ 3 9 1 Fluids, Lubricants and Genuine Parts .
General Maintenance ..................... 3 4 5 Glass Cleaning .......................... 3 7 2 Gross Axle W eight Rating .................. 3 1 5 Gross V ehicle W eight Rating ................ 3 1 5 GVWR ............................... 3 1 5 Hands-Free Phone (Uconnect™) .
Immobilizer (Sentry Key) ................... 1 5 Infant Restraint ........................ 64,65 Information Center , V ehicle ................. 1 7 8 Inside Rearview Mirror .................... 8 3 Instrument Cluster .................... 167,168 Instrument Panel and Contr ols .
Anti-Lock ......................... 177,275 Automatic Headlights ................... 1 3 1 Brake Assist W arning ................... 2 8 1 Brake W arning ..................... 173,272 Bulb Replacement ................... 381,382 Courtesy/Reading .....
T ire Pressur e Monitoring (TPMS) ........ 175,301 T raction Control ....................... 2 8 1 T urn Signal ................... 78,133,134,170 V anity Mirror .......................... 8 7 V oltage ............................. 1 6 8 W arning (Instrument Cluster Description) .
Exterior Folding ........................ 8 5 Heated .............................. 8 6 Outside .............................. 8 4 Rearview ............................. 8 3 V anity ............................... 8 7 Modifications/Alterations, V ehicle .
Outside Rearview Mirrors .................. 8 4 Overhead Console ....................... 1 4 5 Overheating, Engine ...................... 3 2 0 Owner’s Manual (Operator Manual) ......... 4,417 Paint Care ............................. 3 6 8 Panic Alarm .
Radio, Satellite (Uconnect 威 studios) ........... 2 2 9 Rear Cupholder ......................... 1 5 9 Rear Seat, Folding ....................... 1 2 7 Rear W indow Defroster ................... 1 6 2 Rear W indow Features .................... 1 6 2 Rearview Mirrors .
Schedule, Maintenance .................... 3 9 4 Seat Belt Maintenance .................... 3 7 2 Seat Belt Reminder ....................... 4 6 Seat Belts .......................... 37,39,76 Adjustable Upper Shoulder Anchorage ........ 4 4 And Pregnant W omen .
Settings, Personal ........................ 1 9 2 Shifting ............................... 2 5 6 Automatic T ransmission .............. 256,260 Shoulder Belt Upper Anchorage .............. 4 4 Shoulder Belts ........................... 3 9 Signals, T urn .
Synthetic Engine Oil ...................... 3 4 7 System, Remote Starting .................... 2 3 T achometer ............................ 1 6 8 T elescoping Steering Column ............... 1 3 9 T emperature Control, Automatic (A TC) ........ 2 4 0 T emperature Gauge, Engine Coolant .
T owing ............................... 3 1 7 24-Hour T owing Assistance ............... 1 0 2 Behind a Motor Home .................. 3 1 7 Disabled V ehicle ....................... 3 3 7 Recreational .......................... 3 1 7 T owing Assistance .
V ehicle Identification Number (VIN) ............ 6 V ehicle Loading ................... 289,315,316 V ehicle Modifications/Alterations .............. 7 V ehicle Storage ....................... 246,381 V ehicle Theft Alarm (Security Alarm) .......... 1 7 V ideo Entertainment System™ (Rear Seat V ideo System) .
Chrysler Group LL C 10D482-126-AC 3rd Edition Printed in U.S.A..
Ein wichtiger Punkt beim Kauf des Geräts Dodge 2010 Charger SRT (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dodge 2010 Charger SRT noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dodge 2010 Charger SRT - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dodge 2010 Charger SRT reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dodge 2010 Charger SRT erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dodge 2010 Charger SRT besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dodge 2010 Charger SRT verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dodge 2010 Charger SRT. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dodge 2010 Charger SRT gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
