Benutzeranleitung / Produktwartung 2005 Neon des Produzenten Dodge
Zur Seite of 246
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ........................... 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ..............
.
INTRODUCTION CONTENTS m Introduction ........................... 4 m How T o Use This Manual ................. 4 m W arnings And Cautions .................. 6 m V ehicle Identification Number .............. 6 m V ehicle Modifications / Alterations ...
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys ................. 9 ▫ Ignition Key Removal ................... 9 ▫ Locking Doors W ith The Key .............. 1 0 ▫ Key-In-Ignition Reminder ................ 1 1 m Sentry Key .
▫ T o Lock The Doors ..................... 1 9 ▫ Horn Chirp Feature ..................... 1 9 ▫ T o Unlock The T runk .................... 2 0 ▫ Using The Panic Alarm .................. 2 0 ▫ Programming Additional T ransmitters ........ 2 0 ▫ General Information .
A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer . Ask your dealer for these numbers and keep them in a safe place. The double sided keys may be inserted into the locks with either side up.
Manual T ransaxle Depress and hold the r elease button located between the ignition switch and the instrument panel. T urn the igni- tion key to LOCK and remove the key . W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition switch, sounds a signal to remind you to r emove the key . NOTE: W ith the driver’s door open, and the key in the ignition, the power door locks will not lock via the interior door lock switch.
• Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (tran- sponder) fault unless the additional part is physi- cally held against the ignition key being used when starting the vehicle.
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
Automatic T ransaxle Ignition Interlock System This system prevents the key fr om being removed unless the shift lever is in P ARK and the shift knob push-button is fully released. It also pr events shifting out of P ARK unless the key is in the ON/RUN or ST AR T positions and you have depressed the brake pedal.
W ARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death.
4. A single chime will sound to signify that you have successfully disabled the double activation feature. Y ou can turn the feature back on by r epeating the above mentioned procedur e. Y ou can turn the feature back on by r epeating the above mentioned procedur e.
Child-Protection Door Lock System (Rear Doors) T o provide a safer envir onment for children riding in the rear seat, the r ear doors of your vehicle have the child- protection door lock system. T o use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
INTERNAL EMERGENCY TRUNK LID RELEASE W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat.
REMOTE KEYLESS ENTR Y — IF EQUIPPED This system allows you to lock or unlock the doors and trunk or activate the panic alarm fr om distances up to about 23 feet (7 meters) using a hand held transmitter . NOTE: A slight delay of up to two seconds can occur before the doors or tr unk will unlock.
A chime will sound to signify that the feature has been successfully completed. T o Unlock the T runk Press the TRUNK button on the transmitter twice to unlock the trunk. NOTE: A slight delay of up to two seconds can occur before the tr unk unlatches.
General Information This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be r eceived, in- cluding interference that may cause undesir ed operation.
3. T o reassemble the transmitter case, snap two halves together . Make sure ther e is an even gap between the two halves. T est transmitter operation.
NOTE: W ith the system armed on vehicles built for Fleet Service , the trunk can be opened with the key without sounding the Theft Alarm. W ith the system armed on Regular Production V ehicles , opening the trunk with the key will cause the Theft Alarm to sound.
OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems. These include the front and rear seat belts for the driver and all passengers, fr ont airbags for both the driver and front passenger and side airbags for both the driver and front passenger .
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. • W earing your belt in the wrong place could make your injuries in a collision much worse.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system.
Lap/Shoulder Belt Untwisting Procedure Use the following procedur e to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point.
2. At about 6 to 12 inches above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if ther e is a collision. Seat Belt Extender If a seat belt is too short, even .
NOTE: The front airbags ar e certified to the Federal regulations that allow less for ceful deployment. If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG.
Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instr u- ment panel knee bolsters to provide impr oved protection for the driver and front passenger . Side airbags also work with seat belts to improve occupant pr otection.
3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door , airbags will inflate forcefully into the space between you and the door .
• Right and Left Side Impact Airbag Control Modules (SIACM) • Interconnecting W iring How The Airbag System W orks Front Airbag System • The front Airbag Control Module determines if a frontal collision is sever e enough to require the airbags to inflate.
W ARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away .
However , if you have not healed significantly within a few days, or if you have any blistering, see your doctor immediately . • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-pr oduct of the process that generates the nontoxic gas used for airbag inflation.
• In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered by the appropriate SIACM, r eleasing a quantity of non- toxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door .
Airbag Light Y ou will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an a.
Infants And Small Children There ar e different sizes and types of r estraints for children from newborn size to the child almost lar ge enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the right seat for your child.
NOTE: For additional information refer to www .seatcheck.org. W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
In addition, there ar e tether strap anchorages behind each rear seating position located in the panel between the rear seat back and the r ear window — under a hinged plastic cover with this symbol on it. (Shown to the left) In recent years, only the tether anchorage has been provided in new vehicles.
Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufactur ers will provide add-on tether strap kits for some of their older products.
In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint r earward and downward into the seat.
ENGINE BREAK-IN RECOMMENDA TIONS The engine in your new vehicle does not requir e a long break-in period. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble or modify the system. Front seat belt assemblies must be r eplaced after a collision.
.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Mirrors .............................. 5 1 ▫ Inside Day/Night Mirror ................. 5 1 ▫ Inside Compass/T emperature Mirr or— If Equipped .......................... 5 1 ▫ Outside Mirror — Driver’s Side .
▫ Passing Light ......................... 6 2 m W indshield W ipers And W ashers ........... 6 3 ▫ W indshield W ashers .................... 6 3 ▫ Mist Function ......................... 6 3 ▫ Intermittent W iper System ................ 6 4 ▫ Lo Speed W ipers .
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view thr ough the rear window . A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle).
Lights • Briefly press the “Right” button to toggle the right reading lamp “ON/OFF”. Repeat the key pr ess to cycle the light • Briefly press the “Left” button to toggle the left reading lamp “ON/OFF”. Repeat the key pr ess to cycle the light.
Compass V ariance • Find your current location and determine the corr ect Zone number from the map. • Press and hold the “Left” button for 5–10 seconds (until “Zone” appears in the display), then release the button. The number displayed is the current Zone value.
Compass Calibration If “CAL” is not displayed, press and hold the “Left” button for 10–15 seconds, or until “CAL” appears in the display , then release the button.
Electric Remote-Control Mirrors — If Equipped Use the mirror select switch, located on the drivers door trim panel, to adjust the view obtained in the outside mirrors. Pr ess the rocker knob to the L or R for Left or Right mirror selection. Use the center of f position to guard against accidentally moving a mirr or position.
W ARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Adjustable Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Pull up or push down on the restraints so that the upper edge is as high as practical. Push in on the release button to lower the head restraint.
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Then lift the safety catch located under the front edge of the hood, near the center and raise the hood. Use the hood prop r od to secure the hood in the open position as shown. T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage.
LIGHTS Front Map/Reading Lights — If Equipped These lights, located under the rearview mirr or , can be turned on by means of switches located at the base of the rearview mirr or . NOTE: The map lights will remain on when the ignition switch is in the Run or Accessory positions.
Dome Light Position Rotate the dimmer control com- pletely upward to the second de- tent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. Daytime Brightness Feature Certain instrument panel components can be illuminated at full brightness during the daytime.
Daytime Running Lights (Canada Only) The front fog lights will come on as Daytime Running Lights whenever the ignition is on, the headlights are of f, and the parking brake is off.
WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch on the control lever . The lever is located on the right side of the steering column. Move the con- trol lever up to select the desir ed wiper speed. Windshield W ashers T o use the washer , pull the control lever towar d you and hold while spray is desired.
Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Move the lever to the first detent (DEL) position, then select the delay interval by turning the end of the lever .
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
W ARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. Y ou could accidentally set the system or cause it to go faster than you want. Y ou could lose control and have an accident. Always leave the system OFF when you are not using it.
Manual T ransaxle: Depressing the clutch pedal will disengage the speed control. A slight increase in engine RPM befor e the speed control disengages is normal. V ehicles equipped with manual transaxles may need to be shifted into a lower gear to climb hills without speed loss.
POWER SUNROOF — IF EQUIPPED The sunroof contr ol is located on the headliner between the sun visors. A single control “tilts” the sunroof to the vent position and also slides the sunroof r earward to the full open position. Move the switch rearwar d to move the sunroof panel to the full vent position.
W ARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. Y ou could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof.
CONSOLE FEA TURES The Standard console with armr est has two front cup holders and a front storage tray . There ar e two additional cupholders; one is molded in the center of the console to hold large cups, and the other is on the underside of the console lid to serve passengers in the rear seat.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS m Instrument Panel Featur es ................ 7 4 m Standard Instr ument Cluster ............... 7 5 m Optional Instrument Cluster ............... 7 6 m Instrument Cluster Descriptions ............ 7 7 m Electronic Digital Clock .
▫ CD Player Operation .................... 9 0 ▫ CD Changer Control Capability — If Equipped .. 9 2 m Satellite Radio — If Equipped .............. 9 3 ▫ System Activation ...................... 9 4 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) .
m Radio Operation And Cellular Phones ....... 1 0 1 m Climate Controls ...................... 1 0 1 ▫ Heater Only ......................... 1 0 1 ▫ Side W indow Demisters ................. 1 0 3 ▫ Outside Air Intake .................... 1 0 3 ▫ Air Conditioning — If Equipped .
INSTRUMENT P ANEL FEA TURES 74 UNDERST ANDING YOUR INSTRUMENT P ANEL.
ST ANDARD INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 75 4.
OPTIONAL INSTRUMENT CLUSTER 76 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Front Fog Light Indicator — If Equipped This light shows when the front fog lights ar e ON. (See page 62 for more information.) 2. Brake System W arning Light This light monitors various brake functions, including brake fluid level and parking brake application.
If the ABS light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is requir ed, however , the conventional brake system will continue to operate normally provided that the BRAKE warning light is not on.
The light does not show the quantity of oil in the engine. This can be determined using the procedur e shown in Section 7. (See page 169 for more information.) 9. Seat Belt Reminder Light When the ignition key is first turned on, this light will come on for about six seconds.
added. If the fuel level drops to about 1/2 gallon, the fuel symbol will begin to flash and the chime will sound several times. 16. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems.
19. Door Ajar Indicator This vacuum fluorescent display indicator illuminates when a door is not completely closed. If the door is open for more than 8 minutes and the ignition key is in the OFF position, the indicator will turn off. 20. T rip Indicator This light will illuminate when the T rip Odometer is in use.
ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position. When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained.
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the fr equency variations that carry the FM signal.
NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Electronic V olume Control The electronic volume contr ol turns continuously (360 degrees) in either dir ection without stopping.
stations to be locked into push-button memory . The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corr esponding button number will be displayed. Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and F ADE.
Cassette Player Features W ith ignition OFF and the sound system OFF , you can eject the tape cassette by pushing the EJECT button. Y ou can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on.
When Dolby is ON, the NR symbol appears on the display . Each time a tape is inserted the Dolby will turn ON. * “Dolby” noise reduction manufactur ed under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Labo- ratories Licensing Corporation.
Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough r oad, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically .
NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up or the bottom to seek down.
Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to incr ease or decrease the T r eble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers.
Inserting The Compact Disc CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may either insert or eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day .
Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play . Mode Press the MODE button r epeatedly to select between the CD player , the optional remote CD changer and the Satellite Radio (if equipped).
Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an inter esting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer .
System Activation T o activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
Selecting Satellite Mode in RBP , RBU, RAZ, RB1 and RBQ Radios Press the MODE button r epeatedly until the word 9 SIRIUS 9 appears in the display . These radios will also display the following: • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds.
Using the PTY (Program T ype) Button (if equipped) Follow the PTY button instr uctions that apply to your radio. PTY Button ( SCAN ( When the desired pr ogram type is obtained, press the 9 SCAN 9 button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type.
CASSETTE T APE AND PLA YER MAINTENANCE T o keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly dimin- ished. 2.
6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3 ⁄ 4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in fr ont of the changer .
Playing Discs The radio will show the CD number , the CD track number , and the T rack T ime Elapsed while the radio is in the CD mode. If more than one CD is loaded in the changer , the changer will automatically play the next disc after playing the last track of the current disc.
Time Button Press this button to switch between time of day and CD track time. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode. If a CD is loaded, press the Mode button to select the CD mode.
6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatur es may become too high. NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. T ry a known good disc befor e considering disc player service.
Mode Control (Air Direction) The mode control allows you to choose from sev- eral patterns of air distri- bution. Y ou can select ei- ther a primary mode, as identified by the sym- bols, or a blend of two of these modes. The center point between modes gives an even blend of both modes.
T emperature Control Use this control to r egu- late the temperature of the air inside the passen- ger compartment. T urn the control clockwise to increase the temperatur e of the air entering the ve- hicle. Side Window Demisters A side window demister outlet is at each end of the instrument panel.
The controls ar e as follows: Fan and Air Conditioning Control Use this control to r egulate the amount of air forced through the system in any mode you select. The fan speeds to the left of the OFF position are for Air Condi- tioning. Choosing one of these speeds turns on the air conditioning compressor .
Bi-Level Air is directed thr ough the panel and floor out- lets. NOTE: There is a dif ference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives impr oved comfort during sunny but cool conditions.
T emperature Control Use this control to r egulate the temperature of the air in- side the passenger compart- ment. The blue area of the scale indicates cooler tem- peratures while the r ed area indicates warmer tempera- tures.
In cold weather , the use of the Recirculate position will cause windows to fog on the inside because of moisture build up inside the vehicle. For maximum defogging, select the Outside Air position.
Operating Tips 108 UNDERST ANDING YOUR INSTRUMENT P ANEL.
W indow Fogging V ehicle side windows tend to fog on the inside in mild rainy or humid weather . T o clear the windows, use the A/C, P ANEL and blower controls. Direct the panel outlets toward the side windows. Do not use r ecirculate without A/C for long periods as fogging may occur .
ELECTRIC REAR WINDOW DEFROSTER A push-button at the center of the instrument panel, below the radio, turns the defroster and the heated mirrors (if equipped) ON or OFF . An amber light shows that the defroster is on. NOTE: The defroster turns of f automatically after 10 minutes of operation.
ST ARTING AND OPERA TING CONTENTS m Starting Procedur es .................... 1 1 4 ▫ Automatic T ransaxle ................... 1 1 4 ▫ Manual T ransaxle ..................... 1 1 4 ▫ Normal Starting ...................... 1 1 4 ▫ Starting In Cold W eather (Below 32°F Of 0°C) .
m Power Steering ........................ 1 2 4 m T ire Safety Information .................. 1 2 4 ▫ T ire Markings ........................ 1 2 4 ▫ T ire Identification Number (TIN) .......... 1 2 7 ▫ T ire Loading And T ire Pressur e ........
▫ T railer T owing Information (Maximum T railer W eight Ratings) ......... 1 4 7 ▫ W arranty ........................... 1 4 7 m Recreational T owing (Behind Motorhome, Etc.) ................ 1 4 8 ▫ T owing This V ehicle Behind Another V ehicle (Flat T owing W ith All Four Wheels On The Ground) .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
Starting in Cold Weather (Below 32°F of 0°C) Slightly depress and hold the accelerator befor e starting the engine. T urn the key to the ST AR T position.
CAUTION! T o prevent damage to the starter , do not crank the engine for more than 15 seconds at a time. W ait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up.
NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. Four Speed Automatic T ransaxle The electronically contr olled transaxle provides a precise shift schedule.
W ARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake.
When frequent transaxle shifting occurs while using the Overdrive range, such as when operating the vehicle under heavy loading conditions (in hilly terrain, travel- ing into strong head winds, or while towing trailers), use the “3” range. “3” Drive This range eliminates shifts into Overdrive.
NOTE: During cold weather , until the transaxle lubri- cant has warmed, you may have difficulty shifting. This is normal and not harmful to the transaxle. Recommended Shift Speeds T o use your manual transaxle for optimal fuel economy , it should be upshifted as listed in tables 1 and 2.
CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transaxle, or clutch. T o maintain a safe speed and prolong brake life, shift down to 2nd or 1st when descending a steep grade.
Y ou should always apply the parking brake before leav- ing the vehicle. W ARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector .
malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the brake warning indicator will light. Anti-Lock Brake System (ABS) — If Equipped The ABS gives increased vehicle stability and brake performance under most braking conditions.
POWER STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pr essure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ( ....blank.... ( = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
ST ARTING AND OPERA TING 131 5.
W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tire rolling r esistance and results in higher fuel consumption.
CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard are always “cold tire inflation pr essure”.
W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare.
Tire Spinning When stuck in mud, sand, snow , or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). See the paragraph on Freeing A Stuck V ehicle in Section 6 of this manual. W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure.
Replacement Tires The tires on your new vehicle pr ovide a balance of many characteristics. They should be inspected regularly for wear and correct cold tir e inflation pressure.
CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear . • Uneven tire wear , such as feathering and one-sided wear .
CAUTION! T o avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage.
Tire Rotation Recommendations T ires on the front and r ear axles of vehicles operate at differ ent loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns.
Spark Knock Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage and immediate service is requir ed. Poor quality gasoline can cause problems such as har d starting, stalling and hesitations.
MMT in Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT .
Fuel system damage or vehicle performance problems resulting fr om the use of such fuels or additives is not the responsibility of the manufactur er . NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Lamp to turn on.
W ARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. Y ou could be burned. Always place gas containers on the ground while filling. VEHICLE LOADING V ehicle Loading Capacities Front Seat Occupants ..
T railer T owing Information (Maximum T railer Weight Ratings) ( T railer T owing Guide ( NOTE: For trailer towing information (maximum trailer weight ratings) refer to the following website address: http:// www .dodge.com/towing. In Canada, refer to the following website addr ess: http:// www .
W ARNING! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail. Y ou might not have brakes when you need them and could have an accident. • Do not attempt to tow a trailer while using a compact spare tir e.
WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Flasher ................. 1 5 0 m If Y our Engine Overheats ................ 1 5 0 m Jacking And T ire Changing ............... 1 5 2 ▫ Preparations For Jacking ................ 1 5 2 ▫ Instructions .
HAZARD W ARNING FLASHER The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and r ear direc- tional signals will flash. Depress the switch again to turn Hazard W arning Flashers off.
the fan control to High. This allows the heater cor e to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle.
JACKING AND TIRE CHANGING W ARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
1. Remove the spare wheel, scissors jack and lug wrench from stowage. 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground. CAUTION! Do not attempt to raise the vehicle by jacking on the crossmember below the radiator or on the front suspension crossmember .
Do not raise the vehicle until you are sur e the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire clears the surface. Miminum tire lift pr ovides maximum vehicle stability . W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable.
100 ft. lbs. (135 N·m). If you are not sur e about the tightness, have them checked with a torque wr ench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free. Stow the lug wr ench, replaced tire, and jack.
1. W ear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch.
W ARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water .
8. When removing the jumper cables, reverse the above sequence exactly . Be careful of the moving belts and fan. W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3.
T raction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and r oad surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability . T o reduce this possibility , the following precautions should be observed: 1.
CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55km/h).
Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. A dolly should be used under the front wheels if the r ear wheels are raised. Proper towing equipment is necessary to pr event dam- age to the vehicle.
.
MAINT AINING YOUR VEHICLE CONTENTS m 2.0L Engine Compartment ............... 1 6 5 m Onboard Diagnostic System — OBD II ...... 1 6 6 m Emissions Inspection And Maintenance Programs ............................ 1 6 7 m Replacement Parts .............
▫ Hoses And V acuum/V apor Harnesses ....... 1 8 5 ▫ Brake System ........................ 1 8 6 ▫ Automatic T ransaxle ................... 1 8 8 ▫ Manual T ransaxle ..................... 1 9 0 ▫ Appearance Care And Protection From Corrosion .
2.0L ENGINE COMP ARTMENT MAINT AINING YOUR VEHICLE 165 7.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle’s emissions control system.
If your OBD system is not ready , you should see your authorized dealer or repair facility . If your vehicle was recently serviced or had a battery failur e or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX r eading on these engines.
• Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sustained high speeds during hot weather , above 90°F (32°C) • T railer towi.
American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only r ecommends API Certified engine oils. Engine Oil V iscosity (SAE Grade) SAE 5W -20 engine oil is recommended for all operating temperatures.
Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All of this manufacturers engines have a full-flow type disposable oil filter . Use a filter of this type for replace- ment. The quality of replacement filters varies consider - ably .
CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly .
Ignition Wiring System The ignition cables should be kept clean and properly connected. T erminals should be fully seated. Cracked, damaged, or faulty cables should be replaced. Crankcase Emission Control System Proper operation of this system depends on fr eedom from sticking or plugging due to deposits.
Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is perma- nently sealed. Y ou will never have to add water , nor is periodic maintenance requir ed. CAUTION! When servicing the battery , always reinstall the battery thermowrap. The thermowrap provides bat- tery heat protection and will extend overall battery life.
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not requir ed. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated.
Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner , or use the washer solvent. This will remove accumulations of salt or r oad film and help reduce str eaking and smearing.
Windshield W asher Aiming T o change the aim of the windshield washers, place a safety pin into the nozzle opening and move the nozzle slightly . Continue making slight adjustments until you obtain the desired pattern.
Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner .
Adding Coolant Y our vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Y ears or 100,000 miles before replacement. T o prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
W ARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator . If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven.
Insure nylon tubing in these ar eas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they ar e secure and no leaks are present. Components should be replaced immediately if ther e is any evidence of degradation that could cause failure.
NOTE: Inspection of brake hoses should be done whenever the brake system is serviced and every engine oil change. W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately .
W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter .
T o check the fluid level properly , the following procedure must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4. Place the gear selector momentarily in each gear position ending with the lever in P (P ARK).
CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. T o prevent dirt and water from entering the transaxle after checking or replen- ishing fluid, make certain that the dipstick cap is seated properly .
Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the following conditions exist: • The lubricant has become contaminated with water .
W ashing • W ash your vehicle regularly . Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water . • If insects, tar or other similar deposits have accumu- lated on your vehicle, wash it as soon as possible.
• If you carry special cargo such as chemicals, fertilizers, deicer salt, etc., be sure that such materials ar e well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
Y our leather upholstery can be best preserved by r egular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed pr omptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar T otal Clean.
Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instr uments in the vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content of abrasive cleaners.
MAXI FUSE Amp/Color Items Fused 1— — 2— — 3 40 Amp/ Green Headlamps 4 40 Amp/ Green Ignition Run 5 30 Amp/Pink ABS Solenoid 6 30 Amp/Pink Radiator Fan 7 Spare 8 40 Amp/ Green ABS Pump 9 30 Amp.
Interior Fuses The fuse access panel is behind the end cover at the left side of the instrument panel. T o remove the panel, pull it out, as shown. A diagram identifying the components and circuits is located on the inside of the cover .
17 10 Amp/Red Lt Low Beam Headlamp/ Headlamp Level Switch (Bux Only) 18 10 Amp/Red Rt Low Beam Headlamp/ Headlamp Level Motor 19 10 Amp/Red Fog lamps 20 Spare CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
LIGHT BULBS — Inside Bulb No. Seat Belt Indicator ....................... L E D Security Alarm Indicator ................... L E D Malfunction Indicator Light ................ L E D T urn Signal Indicator .................... PC194 V oltage Indicator .
2. Remove two screws from the headlight assembly and remove the assembly fr om the vehicle. NOTE: The headlight assembly is located to the fender by a molded pin. Pull the outboard side of the headlight straight out until the molded pin clears the fender , then slide the headlight out from behind the bumper fascia and grille.
Front Park/T urn Signal Lights 1. Remove the headlight assembly 2. T wist the bulb socket 1/4 turn and remove. 3. Pull the bulb from the socket and replace. Front Sidemarker Light 1. Remove the screws and push-pins from the fr ont fender splash shield.
FLUIDS AND CAP ACITIES U.S. Metric Fuel (Approximate) 2.0L Engines 87 Octane 12.5 Gallons 47.5 Liters Engine Oil-W ith Filter 2.0 Liter Engines (SAE 5W -20, API Certified Engine Oil) 4.5 qts 4.3 Liters Cooling System * 2.0 Liter Engines (Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula), or equivalent.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) or equivalent Engine Oil Use API Certified SAE 5W -20 Engine Oil.
.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance ...... 2 0 6 m Maintenance Schedules .................. 2 0 6 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system.
• If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the 9 Maintenance Schedules 9 section of this manual.
• Check the fluid levels of coolant reservoir , brake master cylinder , power steering and transaxle and add as needed. • Check all lights and all other electrical items for correct operation. • Check rubber seals on each side of the radiator for proper fit.
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L .
Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XX X XX Rotate tires. X X Inspect the front brake pads and r ear brake linings and rotors.
Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers ) (29 000) (34 000) (38 000) (43 000) (48 000) Change engine oil and engine oil filter , if not re- placed at 3 months.. XX X XX Rotate tires. X X X Inspect the front brake pads and r ear brake linings and rotors.
Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XX X XX Rotate tires. X X Inspect the front brake pads and r ear brake linings and rotors.
Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (77 000) (82 000) (86 000 ) (91 000) (96 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XX X XX Rotate tires. X X X Inspect the front brake pads and r ear brake linings and rotors.
Miles 63,000 66,000 69,000 72,000 75,000 ( Kilometers) (101 000) (106 000 ) (1 10 000 ) (1 15 000) (120 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XX X XX Rotate tires. X X Inspect the front brake pads and r ear brake linings and rotors.
Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000 ) (134 000 ) (139 000 ) (144 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XX X XX Rotate tires. X X X Inspect the front brake pads and r ear brake linings and rotors.
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (149 000) (154 000) (158 000 ) (163 000) (168 000) Change engine oil and engine oil filter , if not re- placed at 3 months. XX X XX Rotate tires. X X Inspect the front brake pads and r ear brake linings and rotors.
Miles 108,000 11 1,000 1 14,000 1 17,000 120,000 (Kilometers) (173 000) (178 000) (183 000 ) (188 000) (193 000) Change engine oil and engine oil filter , if not replaced at 3 months. XX X XX Rotate tires. X X X Inspect the front brake pads and r ear brake linings and rotors.
Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) (58 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Rotate tires. X XXXXX Inspect the brake linings.
Miles 42,000 48,000 54,000 60,000 66,000 (Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) [Months] [42] [48] [54] [60] [66] Change engine oil and engine oil filter . XXXXX Rotate tires. XXXXX Inspect the brake linings. X Replace the engine air cleaner filter .
Miles 72,000 78,000 84,000 90,000 96,000 102,000 (Kilometers) (1 15 000) (125 000) (134 000) (144 000) (154 000) (160 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X X X X X X Rotate tires. X X X X X X Inspect the front brake pads and r ear brake linings and rotors.
Miles 108,000 1 14,000 120,000 (Kilometers) (173 000) (182 000) (192 000) [Months] [108] [1 14] [120] Change engine oil and engine oil filter . X X X Rotate tires. X X X Inspect the front brake pads and r ear brake linings and rotors. X X Replace the engine air cleaner filter .
W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .............................. 2 2 4 ▫ Prepar e For The Appointment ............ 2 2 4 ▫ Prepar e A List ........................ 2 2 4 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
• If for some reason you ar e still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center .
Service Contract Y ou may have purchased a service contract for your vehicle to help protect you fr om the high cost of unex- pected repairs after your manufactur er’s new vehicle limited warranty expires. The manufactur er stands be- hind only the manufacturer’s Service Contracts.
W ARRANTY INFORMA TION See your manufacturer’s W arranty Information Booklet for information on warranty coverage and transfer of warranty . IF YOU NEED CONSUMER ASSIST ANCE 227 9.
U.S. ONL Y 228 IF YOU NEED CONSUMER ASSIST ANCE.
MOP AR T P ARTS Mopar t fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best.
• Service Manuals. These comprehensive service manuals pr ovide the information that students and professional technicians need in diagnosing/troubleshooting, pr oblem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles.
DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway T raffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car .
T emperature Grades The temperature grades ar e A (highest), B, and C, repre- senting the tire’s r esistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10.
ABS (Anti-Lock Brake) System ............. 1 2 3 Adding Engine Coolant (Antifreeze) ......... 1 8 3 Adding Fuel .......................... 1 4 4 Air Cleaner , Engine (Engine Air Cleaner Filter) . 175 Air Conditioning .................... 103,177 Air Conditioning Controls .
Brake, Parking ......................... 1 2 1 Brake System ....................... 122,186 Anti-Lock ........................... 1 2 3 Hoses .............................. 1 8 6 Master Cylinder ...................... 1 8 7 Parking ...................
Compact Spare T ire ..................... 1 3 5 Compass .............................. 5 1 Compass Calibration ..................... 5 4 Compass V ariance ....................... 5 3 Console ............................... 7 0 Contract, Service ......
Emergency , In Case of Jacking ............................. 1 5 2 Jump Starting ........................ 1 5 5 T owing ............................. 1 6 0 Emergency T runk Release ................. 1 8 Emission Control System Maintenance .... 167,206 Engine .
Fuel .............................. 141,203 Adding ............................. 1 4 4 Capacity ............................ 2 0 2 Filler Cap ........................... 1 4 4 Filter .............................. 1 7 5 Gauge .........................
Interior Fuses .......................... 1 9 7 Interior Lights .......................... 6 0 Intermittent W ipers ...................... 6 4 Introduction ............................ 4 Jack Operation ......................... 1 5 2 Jacking Instructions .
Rear Servicing ....................... 2 0 1 Rear T ail ............................ 2 0 1 Seat Belt Reminder ..................... 7 9 Security Alarm ........................ 2 2 Side Marker ......................... 2 0 1 Theft Alarm ...............
Odometer T r i p ................................ 8 0 Oil, Engine ......................... 169,202 Capacity ............................ 2 0 2 Change Interval ...................... 1 7 0 Checking ........................... 1 6 9 Disposal ..........
Rear W indow Defroster .................. 1 1 0 Reclining Front Seats ..................... 5 6 Recommended Fluids, Lubricants and Genuine Parts ............................... 2 0 3 Recreational T owing ..................... 1 4 8 Reformulated Gasoline .
Shift Speeds, Manual T ransaxle ............ 1 2 0 Shoulder Belt Upper Anchorage ............. 2 8 Side Airbag ............................ 3 7 Side W indow Demisters ............... 103,109 Slippery Surfaces, Driving On ............. 1 5 8 Snow T ires .
Load Capacity .................... 128,129 Quality Grading ...................... 2 3 1 Radial ............................. 1 3 5 Replacement ......................... 1 3 8 Rotation ............................ 1 4 1 Safety .........................
W arning Lights (Instrument Cluster Description) . 77 W arnings and Cautions .................... 6 W arranty Information .................... 2 2 7 W asher , Adding Fluid ................... 1 8 0 W ashers, W indshield ..................... 6 3 W ashing V ehicle .
246 INDEX.
Ein wichtiger Punkt beim Kauf des Geräts Dodge 2005 Neon (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dodge 2005 Neon noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dodge 2005 Neon - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dodge 2005 Neon reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dodge 2005 Neon erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dodge 2005 Neon besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dodge 2005 Neon verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dodge 2005 Neon. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dodge 2005 Neon gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
