Benutzeranleitung / Produktwartung 36 / 968999609 des Produzenten Dixon
Zur Seite of 80
English Operator’ s Manual SPEEDZTR 44 / 968999538 SPEEDZTR 36 / 968999539 SPEEDZTR 44 / 968999547 SPEEDZTR 36 / 968999609 SPEEDZTR 44 / 968999611 SPEEDZTR 42 / 968999689 SPEEDZTR 42 / 968999713 Please read the operator’ s manual car efully and make sure y ou understand the instructions befo re using the machine.
.
TABLE OF CONTENTS General ............................................................. 4 Driving and Transport on Public Roads ......... 4 Towing ........................................................... 4 Operating ................................
English - 4 INTRODUCTION Congratulations Thank you for purchasing a Dixon ride-on mower. This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance.
English - 5 INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer.
English - 6 SYMBOLS AND DECALS These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. Used in this publication to notify the reader of a risk of personal injury or death , particularly if the reader should neglect to follow instructions given in the manual.
English - 7 SYMBOLS AND DECALS Read Shut off engine and Keep a safe Use on slopes No passengers Operator’s remove key before distance from no greater Manual performing any the machine than 10° main.
English - 8 SAFETY Safety Instructions These instructions are for your safety. Read them carefully. IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
English - 9 SAFETY • Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting.
English - 10 SAFETY Personal Safety Equipment • Make sure that you have first aid equipment close at hand when using the machine. • Never use the machine when barefoot. • Always wear protective shoes or boots, preferably with steel toe caps. • Always wear approved protective glasses or a full visor when assembling or driving.
English - 11 SAFETY grass catchers or other attachments; they can affect the stability of the machine. Do not use on steep slopes. • Do not try to stabilize the machine by putting your foot on the ground. • Do not mow near drop-offs, ditches, or embankments.
English - 12 SAFETY Maintenance Safe Handling of Gasoline To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. • Extinguish all cigarettes, cigars, pipes, and other sources of ignition.
English - 13 SAFETY General Maintenance • Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. • Never tamper with safety devices. Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris buildup.
English - 14 SAFETY • Ensure that nuts and bolts, especially the fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition. • Do not modify safety equipment. Check regularly to be sure it works properly.
English - 15 SAFETY • The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them. • Check the parking brake’s functionality regularly. Adjust and service as necessary. • The mulch blades should only be used in familiar areas when higher quality mowing is desired.
English - 16 SAFETY Customer responsibilities • Read and observe the safety rules. • Follow a regular schedule in maintaining, caring for and using your mower. • Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual.
CONTROLS English - 17 Controls This operator’s manual describes the Dixon Zero Turn Rider. The rider is fitted with either a Briggs & Stratton or Kohler four-stroke overhead valve engine developing 16 - 22 horse power.
CONTROLS English - 18 1. Motion Control Levers The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position. Furthermore, there is a neutral position, which is locked if the steering controls are moved outward.
CONTROLS English - 19 Seat adjustment 8050-165 2. Seat adjustment lever The seat can be adjusted lengthways. When making adjustments, sit on the seat. Slide the lever to the side and maneuver seat to appropriate placement and release lever.
CONTROLS English - 20 4. Refueling The machine has one fuel tank, just behind the seat. The tank capacity is 4.5 gallons (17 liters). The engine will run on a minimum of 85-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used.
CONTROLS English - 21 5. Ignition Switch The ignition key is placed on the driver’s panel and is used to start and stop the engine. 6. Choke Control The choke is used for cold starts to provide the engine with a richer fuel mixture. Two choke options are available, depending on model.
CONTROLS English - 22 8. Blade switch In order to engage the mower deck, pull the knob out; the mower blades are disengaged when the knob is depressed. 9. Circuit breaker The circuit breaker provides protection for the electrical system by (1) 15 amp circuit breaker.
CONTROLS English - 23 8050-774 1. Lift lever 2. Trigger 3. Set pin 4. Foot pedal Cut height lift lever and pedal 1 3 4 IMPORTANT INFORMATION In order to obtain an even cutting height it is important that the air pressure in all four tires is the same 15 psi (1 bar).
English - 24 OPERATION Operation Read “Safety Instructions” section and following pages, if you are unfamiliar with the machine. Training Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities.
English - 25 OPERATION Before Starting • Read the sections Safety Instructions and Controls before starting the machine. • Perform the daily maintenance before starting (see Maintenance Schedule in the Maintenance section). • Check that there is sufficient fuel in the fuel tank.
English - 26 OPERATION • Move the steering controls outward to the locked (outer) neutral position. • Move the throttle to the middle position. • If the engine is cold, the throttle control should be pushed forward to its choke position. • Press in and turn the ignition key to the start position.
English - 27 OPERATION • When the engine starts, immediately release the ignition key back to the run position. • Set the desired engine speed with the throttle. • Allow the engine to run at a moderate speed, “half throttle”, for 3-5 minutes before loading it too heavily.
English - 28 OPERATION To start an engine with a weak battery If your battery is too weak to start the engine, it should be recharged. (See “Battery” in the Maintenance Section.
English - 29 OPERATION Running 1. Release the parking brake by moving the lever downward. Your mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.
English - 30 OPERATION In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.
English - 31 OPERATION Mowing Tips • Observe and flag rocks and other fixed objects to avoid collisions. • Begin with a high cutting height and reduce it until the desired mowing result is attained. The average lawn should be cut to 2½" (64 mm) during the cool season and over 3" (76 mm) during the hot months.
English - 32 OPERATION Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling.
English - 33 OPERATION Moving by Hand Unlocking Transmission When pushing or pulling the mower, be sure to engage the IZT (Integrated Zeroturn Transaxle) bypass linkages. • Always turn off engine before engaging or disengaging the hydro release (free wheel) lever.
English - 34 Daily Weekly A t Maintenance Interval Least In Hours Once Each Y ear Maintenance Page Before After 25 50 100 300 Check the parking brake z Check the engines oil level (every refueling) z .
English - 35 Daily Weekly A t Maintenance Interval Least In Hours Once Each Y ear Maintenance Page Before After 25 50 100 300 Check/adjust throttle cable z Check the condition of belts, belt pulleys, etc.
English - 36 Battery Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight.
English - 37 Ignition System The engine is equipped with an electronic ignition system. Only the spark plug requires maintenance. For recommended spark plug, see Technical Data. 1. Remove the ignition cable boot and clean around the spark plug. 2. Remove the spark plug with a spark plug socket wrench.
English - 38 Checking the Engine’s Cooling Air Intake Check that the engine’s cooling air intake is free from leaves, grass, and dirt. If the cooling air intake is clogged, engine cooling deteriorates, which can lead to engine damage.
English - 39 Replacing the Air Filter If the engine seems weak or runs unevenly, the air filter may be clogged. If run with a dirty air filter, the spark plugs can become fouled, disrupting operation. For this reason, it is important to replace the air filter regularly (see the heading Maintenance Schedule for the proper service interval).
English - 40 4. Tap the paper filter against a fixed surface to remove dust. If the paper filter is still dirty, it must be replaced. Refit the air filter as follows: 1. Check that the seal on the bottom of the paper filter is whole. 2. Mount the paper filter in the air filter housing and tighten the wing nuts.
English - 41 Checking Tire Pressures All four tires should have a pressure of 15 psi / 103 kPa /1 bar. Checking the Parking Brake Visually check that no damage is found on the lever, linages, or switch belonging to the parking brake. Perform a stand still test and check that there is a braking action.
English - 42 Deck belt removal 1. Park on a level surface. Apply parking brake. 2. Lower the deck into the lowest cutting position. 3. Remove bolts from belt shields and remove shields. 4. Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface.
English - 43 Pump Belt To replace EZT (E-Series Zeroturn Transaxle) belt Park the mower on a level surface. Engage the parking brake. EZT belt removal NOTE: Be careful not to damage the fan blades on the EZT´s as this can affect cooling or damage the EZT´s • Remove the deck belt (see Deck Belt Removal in this section of the manual).
English - 44 Blade replacement • Remove blade bolt by turning counterclockwise. • Install new or re-sharpened blade with stamped “GRASS SIDE” facing towards ground/grass (down) or “THIS SIDE UP” facing deck and cutter housing. • Install and tighten blade bolt securely.
English - 45 Adjusting the Mower Deck Check the tire pressure before adjustment of the mower deck. See “Checking Tire Pressure” in Maintenance section. Faulty mower deck adjustments will cause an uneven mowing result. To level deck Adjust the deck while the mower is on a level surface.
English - 46 To adjust anti-scalp rollers Deck has anti-scalp rollers. Anti-scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position. Anti- scalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions.
English - 47 Parking brake To adjust parking brake Jack up unit and support properly with jack stands. Allow clearance to work at rear transaxles. Before making any adjustments: Set park brake. Measure the distance between the rod swivel pin and the brake arm washer.
English - 48 Tracking adjustment If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 15 psi (1 bar). If the unit will not track straight, follow the steps below. Tracking must be checked on a flat and level concrete or blacktop surface.
English - 49 LUBRICATION Lubrication Lubrication Schedule 7 * 8011-672-3 General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil. When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulfide grease.
English - 50 LUBRICATION Lubricating the Cables If possible, grease both ends of the cables and move the controls to end stop positions when lubricating. Refit the rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not lubricated regularly.
English - 51 LUBRICATION Deck outer spindle Lubricate using a grease gun, one zerk, each side 2- 3 strokes. Use only good quality bearing grease. Engine Oil Changing the Engine Oil The engine oil should be changed for the first time after 5-8 hours of operation.
English - 52 LUBRICATION Checking the Oil Level Check the oil level in the engine when the machine is standing level and the engine is stopped. Remove the dipstick, wipe it clean, and then replace it. The dipstick should be screwed into place. Take the dipstick out again and read the oil level.
English - 53 LUBRICATION Changing the Engine Oil Filter 1. Drain the engine oil in accordance with the work description under the heading Engine Oil/ Change Engine Oil. 2. Remove the oil filter. If necessary, use a filter remover. 3. Wipe new, clean engine oil onto the seal for the new filter.
English - 54 LUBRICATION 7. Drain old oil filters of all free flowing oil prior to disposal. Place used oil in appropriate containers and dispose of it in accordance with laws in your area. 8. Remove the top port plug (see illustration) from the left side and right side of the transaxles prior to filling with oil.
English - 55 LUBRICATION Purging Procedures Due to the effects air has on efficiency in hydrostatic drive applications, it is critical that it is purged from the system. These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional oil has been added to the system.
English - 56 TROUBLE SHOOTING GUIDE Trouble Shooting Guide Problem Cause The engine will not start. • The blade switch is engaged. • The steering controls are not locked in the neutral position. • The driver is not sitting in the driver’s seat.
English - 57 TROUBLE SHOOTING GUIDE The engine seems weak. • Clogged air filter. • Defective spark plugs. • Carburetor incorrectly adjusted. • Air trapped in hydraulic system. The engine overheats. • Clogged air intake or cooling fins. • Engine overloaded.
English - 58 TROUBLE SHOOTING GUIDE Uneven mowing results. • Different air pressure in the tires on the left and right sides. • Bent blades. • The suspension for the mower deck is uneven. • The chain fixture has come loose. • The blades are dull.
English - 59 STORAGE Storage Winter Storage At the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than 30 days). Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function.
English - 60 WIRING DIAGRAMS Wiring diagram.
English - 61 Engine Manufacturer Kohler Briggs & Stratton Type Courage Intek Power 20 hp 16 hp Lubrication Pressure with oil filter Pressure with oil filter Oil capacity excl filter Oil capacity incl filter 1.
English - 62 Equipment Cutting width 44" 36" Cutting height 1.5" - 4.5" 1.5" - 4.5" Uncut circle 0 0 Number of blades 3 2 Blade length 14.
English - 63 Engine Manufacturer Briggs & Stratton Briggs & Stratton Type Intek ELS Power 16 hp 22 hp Lubrication Pressure with oil filter Pressure with oil filter Oil capacity excl filter 1.3 qt (1.31 liters) 1.875 qts (1.8 liters) Oil capacity incl filter 1.
English - 64 Equipment Cutting width 36" 44" Cutting height 1.5" - 4.5" 1.5" - 4.5" Uncut circle 0 0 Number of blades 2 3 Blade length 18.
English - 65 Engine Manufacturer Briggs & Stratton Briggs & Stratton Type Intek ELS Power 19 hp 19 hp Lubrication Pressure with oil filter Pressure with oil filter Oil capacity excl filter 1.3 qt (1.31 liters) 1.3 qt (1.3 liters) Oil capacity incl filter 1.
English - 66 Equipment Cutting width 42" 42" Cutting height 1/5" - 4.5" 1/5" - 4.5" Uncut circle 0 0 Number of blades 2 2 Blade length 21 " 2 1" Nose rollers No.
English - 67 Engine Manufacturer Briggs & Stratton Type ELS Power 2 2 hp Lubrication Pressure with oil filter Oil capacity excl filter 1.875 qt (1.
English - 68 ZTR 44 / 968999547 TECHNICAL DATA Equipment Cutting width 44" Cutting height 1.5" - 4.5" Uncut circle 0 Number of blades 3 Blade length 14.
English - 69 TECHNICAL DATA Accessories BioClip attachment (Mulch kit) Collection system Torque Specifications ·Engine crankshaft bolt 50 ft/lb (67 Nm) ·Deck pulley bolts 45 ft/lb (61 Nm) ·Lug nuts.
English - 70 CONFORMITY CERTIFICATES Conformity Certificates USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.
English - 71 SERVICE JOURNAL Service Journal Action Date, mtr reading, stamp, sign Delivery Service 1. Charge the battery. 2. Adjust the tire pressure of all wheels to 15 PSI (1 bar). 3. Mount the steering controls in the normal position. 4. Connect the contact box to the cable for the seat’s safety switch.
English - 72 SERVICE JOURNAL After the First 5-8 Hours 1. Change engine oil..
English - 73 SERVICE JOURNAL Action Date, mtr reading, stamp, sign 25-Hour Service 1. Check the fuel pump’s air filter. 2. Sharpen/Replace mower blades if required. 3. Check the tire pressures. 4. Check battery with cables. 5. Lubricate according to lubrication chart.
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 50-Hour Service 1. Perform the 25-hour service. 2. Clean/replace the air cleaner’s filter cartridge (paper filter) (shorter intervals for dusty operating conditions). 3. Change engine oil. 4. Lubricate according to lubrication chart.
Action Date, mtr reading, stamp, sign 100-Hour Service 1. Perform the 25-hour service. 2. Perform the 50-hour service. 3. Change the engine oil filter. 4. Clean/replace the spark plugs. 5. Replace the fuel filter. 6. Clean the cooling fins on the engine and transmission.
SERVICE JOURNAL Action Date, mtr reading, stamp, sign 300-Hour Service 1. Inspect the machine. Come to agreement with the customer as to which additional work is to be carried out. 2. Perform the 25-hour service. 3. Perform the 50-hour service. 4. Perform the 100-hour service.
SERVICE JOURNAL Action Date, mtr reading, stamp, sign At Least Once Each Year 1. Clean the engine’s cooling air intake (25 hours). 2. Replace the air cleaner’s pre-filter (foam) (300 hours). 3. Replace the air filter’s paper cartridge. 4. Change the engine oil (50 hours).
SERVICE JOURNAL Action Date, mtr reading, stamp, sign.
.
Part No. 539 131911 Rir (07/27/07).
Ein wichtiger Punkt beim Kauf des Geräts Dixon 36 / 968999609 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dixon 36 / 968999609 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dixon 36 / 968999609 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dixon 36 / 968999609 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dixon 36 / 968999609 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dixon 36 / 968999609 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dixon 36 / 968999609 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dixon 36 / 968999609. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dixon 36 / 968999609 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
