Benutzeranleitung / Produktwartung OD-2050HD des Produzenten AirLive
Zur Seite of 87
AirLive OD-2050HD 1 l Ai r Liv e OD-2050HD 2-Me gaPixel IR Outdoor V andal P oE IPCAM Use r ’ s Manual.
Copyright and Disclaimer AirLive OD-2050HD i Owner's Record The model and serial numbers are located at the bottom of dev ice. Record these numbers in the spaces provided below . Refer to thes e numbers whenever you call upon your dealer regarding this product.
Copyright and Discl aimer AirLive OD-2050HD ii Notice: The changes or modifications not expressly approved by the p arty responsible for compliance could void the user ’ s authority to operate the equipment.
Copyright and Disclaimer AirLive OD-2050HD iii IMPOR T ANT NOTE: T o comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitt ed. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user ’s authority to operate the device.
T able of Contents i AirLive OD-2050HD T able of Content s 1. Intr oducti on ................................................................................................................ .1 1.1 Over view ............................................
T able of Contents AirLive OD-2050HD ii 4.3.3 Main tenance ............................................................................................38 4.4 V ideo: Confi gure Prof ile .................................................................
1. Introduction AirLive OD-2050HD User ’ s Manual 1 1 1. Introduction 1.1 Overview The OD-2050HD is the high-end network camera with IP66 rated weather and vandal proof housing. The built-in IR LED can pr ovide additional light source when the environment is dim or even dark.
1. Introduction AirLive OD-2050HD User ’ s Manual 2 Features 16:9 Full HD V ideo Resolution, Support up to 1080P@30fps IP66 Weather and V andal Proof housing for Outdoor Environment Built-in IR LED and IR-Cut Removable for Day & Night Use Support 802.
1. Introduction AirLive OD-2050HD User ’ s Manual 3 Quick Start Guide provides imp ortant information and instructio ns for installing this device. Note : Using a power supply with a dif ferent vo ltage than the one included with the Network Camera will cause damage and void the warranty for this product.
1. Introduction AirLive OD-2050HD User ’ s Manual 4 Power (orange color) This LED is used to indicate whether DC pow er is on or not. In addition, this LED will be flashing while the wireless accessing of the Camera.
1. Introduction AirLive OD-2050HD User ’ s Manual 5 1.4 Mounting the Camera Ceiling Mount Fix the camera with as below. Install the Camera in LAN 1. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN so cket and attach it into the network.
2. Preparation AirLive OD-2050HD User ’ s Manual 6 2 2. 0 Prep aration 2.1 Search and Set up by IPWizard II When you installed the Camera on a LAN environment, you have two easy ways to search your Cameras by IPWizard II or UPnP™ discovery .
2. Preparation AirLive OD-2050HD User ’ s Manual 7 2.1.2 View If IPWizard II finds network devices, Vi ew button will be available. Please select the device you want to view and click the Vie w button. Then you could s ee the video from camera directly .
2. Preparation AirLive OD-2050HD User ’ s Manual 8 2.1.3 LAN In case you want to change the IP related para meters of wired interfac e, please select the device you want to configure and click the LA N button. Relative settings will be carried out as below .
2. Preparation AirLive OD-2050HD User ’ s Manual 9 In case, you do not want to change user name and/or password, then just cl ick “ Submit ” button to perform your setting accordingly . Click “ << ” button will go back to previous page.
2. Preparation AirLive OD-2050HD User ’ s Manual 10 Click the targeted Device . Then Internet Explorer will connect to this Network Camera automatically . 2.3 Inst all the Device behind a NA T Router Once installed, the device is accessible on your LAN.
2. Preparation AirLive OD-2050HD User ’ s Manual 11 2. Enable UPnP NA T traversal opt ion of the Network Camera Refer to Setting Î Network Î UPnP page for detail NA T traversal setting. Note that this option is default enabled. 2.4 Access the Device from the Internet Explorer for the First T ime 1.
2. Preparation AirLive OD-2050HD User ’ s Manual 12 3. According your browser’s security setting, the IE Web Page may prompt the “Security Warning” window. If so, select “Yes” to install and run the Ac tiveX control into your PC. Otherwise, the system will load the ActiveX silently.
3. Operating the Network Camera AirLive OD-2050HD User ’ s Manual 13 3 3. Operating the Network Camera S tart-up screen will be as follow no matter an ordinary users or an administrator . ActiveX Control Monitor Image Section Full Screen Monitor Image Section The image shot by the device is shown here.
3. Operating the Network Camera AirLive OD-2050HD User ’ s Manual 14 : Disable audio up loading function. : Enable audio uploading function. Full Screen Enlarge video to full screen display . : Enlarge video to full screen display . Pr ess “ESC” key to disable this function.
3. Operating the Network Camera AirLive OD-2050HD User ’ s Manual 15 Digit al Zoom Click Digita l Zoom to active this function as above. User can drag or scale the box over the video to adjust zoom ratio and position. Snap shot Click Snapshot to activate this function.
3. Operating the Network Camera AirLive OD-2050HD User ’ s Manual 16 Record Click Record to activate this function. Pr ess Record button to st art recording. The video file is saved as ASF format into your local PC. While you want to stop it, press S top to stop recording.
3. Operating the Network Camera AirLive OD-2050HD User ’ s Manual 17 About Click About to show this ActiveX information..
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 18 4 4. Administrating the Device System Setting This function is only available for user logged into Camera as administrator .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 19 4.1 Network: Configure Network Settings Use this menu to configure the network to connect the device and the clients. 4.1.1 Network This section provides the menu for connecting the device through Ethernet cable.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 20 Primary DNS and Secondary DNS If you do not select Obtain DNS from DHCP , then you need to enter these p arameters manually . HTTP Port The device supports two HTTP ports. The first one is default port 80 and this port is fixed.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 21 HTTPS Enable/Disable Use this function to enable or disable the HTTPS function. HTTP&HTTPS or HTTPS only User can choose to use both HTTP and HTTPS concurrently , or just use HTTPS as the access method.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 22 DDNS T o enable or disable t he DDNS service here. Server name Choose the built-in DDNS server . DDNS Host The domain name is applied of this device. User name The user name is used to log into DDNS.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 23 The procedures are Connect to a LAN by DHCP or Fixed IP Access the device; enter Setting Î Network Î PPPoE as below PPPoE T o enable or disable the PPPoE service here. User name T ype the user name for the PPPoE service which is provided by the ISP .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 24 RTSP Port Choose the R TSP port. The R TSP protocol al lows a connecting client to start a video stream. Enter the R TSP port number to use. The default value is 554. RTP Port S pecify the range of transmission port number of video stream.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 25 UPnP T o enable or disable the UPnP service here. Friendly Name Shows the friendly name of this device here. UPnP NA T T raversal When enabled, the device will atte mpt to configure port mapping in a NA T router on your network, using UPnP™.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 26 4.1.7 Bonjour Bonjour , also known as zero-configuration networking, enables automatic discovery of computers, devices, and services on IP netwo rks.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 27 ONVIF T o enable or disable this protocol. V ersion Selection Choose the version of the protocol you wanted to use. 4.1.9 IP Filter Y ou can enter different user ’s IP address which are allowing enter or denying by the device.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 28 4.1.10 IP Notification In case the IP address is changed, system is abl e to send out an email to alert someone if the function is enabled. SMTP Notification (e-mail) If enable this function, then the “ Send to “and “ Subject ” fields need to be filled.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 29 TCP Notification If enable this function, then the “ TCP Server “, “ TCP Port ”, and “ Message ” fields need to be filled. TCP Server T ype the server name or the IP address of the TCP server .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 30 Custom p arameter User can set specific parameters to HTTP server . Message The message will be sent to HTTP server . 4.2 Camera: Adjust Camera Parameters Use this menu to set the functions of the camera p arameters of the device.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 31 White Balance Auto: will adjust the white balance automatically . Hold: will hold the white balance. Exposure Control Auto: will adjust the inte rnal gain automatically . Hold: will hold the internal gain.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 32 Noise Reduction Use the function to enable/disable or adjust the de-noise level. Auto Contrast Compensation Use this function to determine the Auto Contrast Compensation level.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 33 4.2.3 PTZ Setting User can configure the RS-485 protocol in this page. RS-485 is an communication interface, in most situation, it is to be used for controlling the scanner .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 34 4.2.4 Preset Setting This page provides the edit tool to modify or delete the “Preset Setting” item by item. 4.2.5 Tour Setting Up to 128 positions can be preset, and the camera can be programming to move to the preset position sequentially .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 35 Running Enable or disable this camera tour . Preset Set the sequence of the tour . Maximum 16 poi nts can be assigned. The selected preset position is added in the Sequence list from 1 to 16.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 36 T o use this service, just follow four steps below: 1. Enable DIPS function of the device 2. Check your Device ID from this page. This is a unique number for each device. 3. If your device is behind a NA T router , pl ease configure your device properly .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 37 Adjust - Synchronize with PC: Click this option to enable time synchronization with PC time.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 38 4.3.3 Maintenance Hard Factory Default (Include the network setting) Recall the device hard factory default settings . Note that click this button will reset all device’ s parameters to the factory settings (including the IP address).
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 39 1. Close all other application programs which are not necessary for firmware update. 2. Make sure that only you access this device while firmware updating. 3. Disable Motion Detection function.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 40 4.4 V ideo: Configure Profile This device provides 2 modes of video prof ile. The first one is Mega-pixel mode which supports video resolution up to Mega-pixel. Howe ver the maximum frame rate of this mode is up to 15fp s only .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 41 4.4.2 Video Profile Name Assign a name to the selected profile. V ideo T ype V ideo codec of the se lected video profile. Resolution Resolution of the selected video profile.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 42 GOP Control Defines the Intra/Inter-fra me (I/P) ratio of this profile. For example, set the GOP to 30, then the video stream will have one In tra-frame every 30 frames. 4.4.3 ROI ROI means Region of Interest.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 43 Audio T o enable or disable audio function Mute While PT Mute the audio while pan and/or tilt motion Audio Mode T o select Simplex or Full duplex (2-way audio) mode Input Gain T o adjust gain of input audio Output Gain T o adjust gain of output audio 4.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 44 PTZ Control Authorize this user to control PTZ function or not. Add, up date, and remove of Users account Manage the user ’s account of viewer user . 4.7 E-Mail: Setup E-Mail Configuration Y ou may setup SMTP mail parameters for furt her operation of Event Schedule.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 45 SMTP Authentication Select the authentication requi red when you send an e-mail. Disable: if no authentication is requir ed when an e-mail is sent. Enable: if authentication is required when an e-mail is sent.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 46 Add and Del T o add or delete the motion windows. User can specify up to 10 Included and/or Excluded windows to monitor the video captured by this device. By dragging mouse on the image, you can change the position and size of t he selected motion window accordingly .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 47 Enable automatic disk cleanup Delete old recorded files while the conditions are reached as below. Remove recordings order than Delete old files by days. Remove oldest recordings when disk is Delete old files by left capacity.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 48 T est Check the FTP server whether this account is available or not. FTP Login name T ype the user name for the FTP server . FTP Login Password T ype the password for the FTP server .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 49 TCP Server T ype the server name or the IP address of the TCP server . TCP Port Set port number of TCP server . 4.11.3 HTTP Server The device also can send event message to specified HTTP server .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 50 Proxy Address T ype the server name or the IP address of the HTTP Proxy . Proxy Login name T ype the user name for the HTTP Proxy . Proxy Login Password T ype the password for the HTTP Proxy .
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 51 SAMBA Login Passw ord T ype the password for the SAMBA server . SAMBA Path Set working directory path of SAMBA server . 4.11 Event Schedule: Configure the Event Schedule 4.12.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 52 Action Define the actions once event triggered. Example 1 Send file to FTP server by motion triggered always: 1. Select event trigger 2. Enable time: start from 00:00 to 24:00 every day 3.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 53 Example 3 Enable V oice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday . 1. T ype: Select schedule trigger and interval is 10-minute. 2. Enable time: Select Monday to Friday , and set start time from 18:00 and keep work i n 6 hours.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 54 4.12.2 Record User can choose the type of record f ile for event or schedule application.
4. Administrating the Device AirLive OD-2050HD User ’ s Manual 55 Record File T ype Choose JPEG , A VI-JPEG , or A VI-H.264 file format. Record File Prefix Define the prefix of recorded filename. JPEG Picture Numbers Define the picture numbers of JPEG to be sent out.
5. Appendix AirLive OD-2050HD User ’ s Manual 56 5 5. Appendix Appendix A: Alarm I/O Connector Some features of the Network Camera can be activated by the external sensor that senses physical changes in the area Network Camera is monitoring. These changes can include intrusion detection or certain physical chan ge in the monitored ar ea.
5. Appendix AirLive OD-2050HD User ’ s Manual 57 Explanation of External I/O Circuit Diagram: CAUTION! − THE LOW VOL T AGE/CURREN T CIRCUITS AND HIGH VOL T AGE/ CURRENT CIRCUITS ARE IN THE NETWORK CA MERA CIRCUIT . THE QUALIFIED ELECTRICIAN SHOULD DO THE WIRI NG NOT BY YOUR SELF .
5. Appendix AirLive OD-2050HD User ’ s Manual 58 Appendix B: T roubleshooting & Frequently Asked Questions Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.264, MPEG4 and JPEG triple compression to providing high quality images.
5. Appendix AirLive OD-2050HD User ’ s Manual 59 password for the first time or af ter factory default reset Note that it’ s all case sensitivity . Forgot the username and password Follow the steps below . 1. Restore the factory def ault setting by press pressing and holding down more than 3 seconds on the device.
5. Appendix AirLive OD-2050HD User ’ s Manual 60 failed support more cameras. Y ou could turn off and on NA T router to clear out of da te information inside router .
5. Appendix AirLive OD-2050HD User ’ s Manual 61 • Some routers reject the global IP address to access the Network Camera on the same LAN. Access with the private IP address and correct port number of Network Camera. • When you use DDNS, you need to set Default Gateway and DNS server address.
5. Appendix AirLive OD-2050HD User ’ s Manual 62 settings changed in order for the device to be accessible outside your LAN. • Make sure that the device isn’t conflicting with any other web server running on your LAN. • Check the configuration of the router settings allow the device to be accessed outside your local LAN.
5. Appendix AirLive OD-2050HD User ’ s Manual 63 streaming and/or reducing t he video streaming size. V ideo quality of the device The focus on the Camera is bad. • The lens is dirty or dust is att ached. Fingerprints, dust, stain, etc. on the lens can degrade the image quality .
5. Appendix AirLive OD-2050HD User ’ s Manual 64 The replies, as illustrated below , will pr ovide an explanation to the problem. If you want to detect any other devices conf licts with the IP address of Network Camera, also can utilize the PING command but you mu st disconnect the device from the network first.
5. Appendix AirLive OD-2050HD User ’ s Manual 65 Note : Audio streaming also takes bandwid th around 32kbp s. Some xDSL/Cable modem upload speeds could not even reach up to 128 kb ps. Thus, you may not be able to receive good quality video while also streaming audio on a 128 kbps or lower connection.
5. Appendix AirLive OD-2050HD User ’ s Manual 66 IGMP, PPPoE, 3GPP, SMB, ICMP Security Password protection IP filter HTTPS Users Up to 20 simultaneous users Ethernet 10/100M Fast Ethernet System Int.
5. Appendix AirLive OD-2050HD User ’ s Manual 67 Appendix F: Configure Port Forwarding Manually The device can be used with a router . If the device wants to be acce ssed from the W AN, its IP address needs to be setup as fixed IP address, also the port forwarding or Virtual Server function of router needs to be setup.
5. Appendix AirLive OD-2050HD User ’ s Manual 68 Y our WAN IP Addre ss will be listed here. Note : Because a dynamic W AN IP can change from time to time depending on your IS P , you may want to obtain a S tatic IP address from your ISP .
5. Appendix AirLive OD-2050HD User ’ s Manual 69 Scheduling should be set to Always so that the camera images can be accessed at any time. A check mark appearing before the entry name will indicate that the ports are enabled. Import ant : Some ISPs block access to port 80.
5. Appendix AirLive OD-2050HD User ’ s Manual 70 Appendix G: DDNS Application Preface If you have a Cable modem or xDSL, this is a great way to host your own Networked Device or other TCP/IP Service. Get your own domain like www . yourname.com, www .
5. Appendix AirLive OD-2050HD User ’ s Manual 71 3. After the columns show up at the lef t side, click “ Create Account ”. 4. Fill the ap plication agreement and necessary information. a. Username b. E-mail address and confirmation c. Password and confirmation d.
5. Appendix AirLive OD-2050HD User ’ s Manual 72 3 Click these two options 5. Check your e-mail mailbox. There will be an e-mail with a title “Y our DynDNS Accoun t Information“. Click the hyperlink address to confirm the DDNS service that you just applied.
5. Appendix AirLive OD-2050HD User ’ s Manual 73 Click to confirm 6. Enter the web p age http://www .dyndns.org/ again. Input your username and password that you just applied to login admin istration interface of DDNS server .
5. Appendix AirLive OD-2050HD User ’ s Manual 74 8. Click the “ Services ”. 9. Click the “ Dynamic DNS ”. 10. Click the “ Get St arted ”.
5. Appendix AirLive OD-2050HD User ’ s Manual 75 11. We could create a domain name without any charge at this step. First, we input the host name. (Pink No.1) Then we pick a domain that is easy to remember . (Pink No.2) The 3rd step is to click “Offline Hostname” from Service T ype.
5. Appendix AirLive OD-2050HD User ’ s Manual 76 is within tolerances and commonly found. Austria 230V 50 Hz Brazil 1 10/220V* 60 Hz *127V found in states of Bahia, Paran?(including Curitiba), Rio de Janeiro, S 緌 Paulo and Minas Gerais (though 220V may be found in some hotels).
5. Appendix AirLive OD-2050HD User ’ s Manual 77 United Kingdom 230V* 50 Hz *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially changed to 230V , 240V is within tolerances and commonly found.
5. Appendix AirLive OD-2050HD User ’ s Manual 78 Appendix J: Enable UPnP of Windows XP Use the following steps to enable UPnP s etti ngs only if your operat ing system of PC is running Windows XP .
5. Appendix AirLive OD-2050HD User ’ s Manual 79 Click Add or Remove Programs Click Add/Remove Windows Components The following screen will appear: Select Networking Services Click Details.
5. Appendix AirLive OD-2050HD User ’ s Manual 80 Select Universal Plug and Play Click Ok Click Next.
5. Appendix AirLive OD-2050HD User ’ s Manual 81 Please wait while Setup configures the components. Click Finish.
Ein wichtiger Punkt beim Kauf des Geräts AirLive OD-2050HD (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie AirLive OD-2050HD noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für AirLive OD-2050HD - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von AirLive OD-2050HD reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über AirLive OD-2050HD erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon AirLive OD-2050HD besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von AirLive OD-2050HD verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit AirLive OD-2050HD. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei AirLive OD-2050HD gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
