Benutzeranleitung / Produktwartung FE-200CU des Produzenten AirLive
Zur Seite of 73
AirLive FE-200CU Manua l 1 FE-200CU 2-Me gaPixel W all Mount Fish Eye P oE IPCAM Use r ’ s Manual.
Copyright and Disclaimer AirLive FE-200CU Manua l i Owner's Record The model and serial numbers are located at t he bottom of device. Record these numbers in the spaces provided below . Refer to t hese numbers whenever y ou call upon your dealer regarding this product.
Copyright and Discl aimer AirLive FE-200 CU Manua l ii Notice: The changes or modifications not expressly approved by the p arty responsible for compliance could void the user ’ s authorit y to operate the equipment.
Copyright and Disclaimer AirLive FE-200CU Manua l iii IMPOR T ANT NOTE: T o comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permi tted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user ’s authority to operate the device.
T able of Content s i FE-200CU T able of Content s 1. Introduction .................................................................................................................1 1.1 Overview ........................................................
T able of Content s AirLive FE-200 CU Manua l ii 4.4 Schedule ............................................................................................................ 32 4.4.1 General ...............................................................
1. Introduction AirLive FE-200CU Manua l 1 1 1. Introduction 1.1 Overview AirLive FE-200CU is a Fish-Eye Network Came ra; it is featured with superior H.264-A VC performance and rich functions. AirLive FE-200CU includes a fish-eye lens for 360° wide angle view without blind spot.
1. Introduction AirLive FE-200CU Manua l 2 The e-PTZ function including preset point without moving part s, can replace part of traditional PTZ camera and thus save lots of cost for maint aini ng traditional mechanical Pan/T ilt. The camera offers optional PoE type for in stallation.
1. Introduction AirLive FE-200CU Manua l 3 1.3 Physical Overview and Connections 1. Light Sensor: The Light sensor is for detecting IP Camera environmental illumination. If IP Camera is in the dark/night environment, IR Cut Filter is switched off to let infrared light pass through for clear night view.
1. Introduction AirLive FE-200CU Manua l 4 5. Reset Button The Reset Button is located on the back panel. To restore to the factory default, please follow the steps: (1.) Unplug the power jack to turn off the power of the camera. (2.) Insert a pin into the reset hole.
1. Introduction AirLive FE-200CU Manua l 5 9. Micro SD Card slot: The IP Camera has built-in a Micro SD card sl ot which can accepts Micro SD memory card for image / video event recording. 1.4 Mounting the Camera 1. T ake out the camera and accessories from the package: The st and and FE-200CU 2.
1. Introduction AirLive FE-200CU Manua l 6 3. Install the FE-200CU onto the stand, and connect the network cable. 4. Y ou can adjust the silver scr ew to fix the angle of camera.
1. Introduction AirLive FE-200CU Manua l 7 1.5 Inst all the Camera in LAN 1. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN so cket and attach it into the network. 2. Connect the external power supply to Camera Connect the attached power adapter to the DC power jack of the camera.
2. Preparation AirLive FE-200CU Manua l 8 2 2. Prep aration 2.1 Search and Set up by IPWizard II When you install the Camera on a LAN environment, you have two easy ways to search your Camera by IPWizard II or UPnP™ discovery . Here is t he way to execute IPWizard II to discover Camera’ s IP address and set up related p arameter in a Camera.
2. Preparation AirLive FE-200CU Manua l 9 2.2 UPnP of Windows® XP , V ist a or 7 UPnP™ is short for Universal Plug and Play , which is a networking architecture that provides compatibility among networking equipment, sof tware, and peripherals. This device is an UPnP enabled device.
2. Preparation AirLive FE-200CU Manua l 10 Click the targeted Device . Then Internet Explorer will connect to this Network Camera automatically . 2.3 Inst all the Device behind a NA T Router Once installed, the device is accessible on your LAN.
2. Preparation AirLive FE-200CU Manua l 11 (2) Enable UPnP NA T traversal opt ion of the Netw ork Camera Refer to Setting Î Network Î UPnP page for det ail NA T traversal setting. Note that this option is default enabled. (3) Access your Network Camera by DIPS Refer to Setting Î System Î System page for detail DIPS information.
2. Preparation AirLive FE-200CU Manua l 12 3. According your browser ’s security setting, the IE W eb Page may prompt the “Security W arning” window . If so, select “Y es” to insta ll and run the ActiveX control into your PC. Otherwise, the system will load the ActiveX silently .
3. Operating the Network Camera AirLive FE-200CU Manua l 13 3 3. Operating the Network Camera S tart-up screen will be as follow no matter an ordinary users or an administrator . Configuration Click for configuring the camera settings. Language The device can provide multiple languages to meet customer ’s requirement.
3. Operating the Network Camera AirLive FE-200CU Manua l 14 Protocol A user can select proper streaming prot ocol according to network environment. Manual T rigger T rigger manually a pr eset event in the configuration page.
3. Operating the Network Camera AirLive FE-200CU Manua l 15 z Quad view & Quad with source view PTZ control panel: 1. Ch ： Select the channel. (1~4) & (2~4) 2. S tep ： Set the speed of Pan/T ilt Function. (1~10) 3. Pan/T ilt Arrow ： Click to control the Pan/T ilt Function.
3. Operating the Network Camera AirLive FE-200CU Manua l 16 Vo l u m e Click S peaker button to activate this function. Scroll the control bars to adjust the audio attribute. Full Screen Enlarge video to full screen display . Pre ss “ESC” key to disable this function.
4. Administrating the Device AirLive FE-200CU Manua l 17 4 4. Administrating the Device System Setting This function is only available for a us er logs into Camera as administrator . Click on each menu name to display its setting p age. Item Action V ideo Configure bit rate and fr ame rate of video profiles.
4. Administrating the Device AirLive FE-200CU Manua l 18 4.1.2 Advanced z S tream Setting Note: Configuration of stream 2 is the same as stream 1, but S tream 2 can only be set to 320x240 or 640x480. z R TSP Path The R TSP Path is the stream ID used for R TSP client streaming connection, such as VLC player .
4. Administrating the Device AirLive FE-200CU Manua l 19 z Image Format H.264 and MJPEG are available for image fo rmat selection. The term, “image format”, is referring to compression / encodi ng technique. The selection of image format decides the performance of bandwid th and storage requirement.
4. Administrating the Device AirLive FE-200CU Manua l 20 4.2 Camera: Adjust Camera Parameters Use this menu to set the functions of the camera p arameters of the device. 4.2.1 General Use this function to determine the Auto Contrast Compensation level.
4. Administrating the Device AirLive FE-200CU Manua l 21 z Audio Setting: Audio Enable: T urn on/of f the audio. z Web Record Setting: Save Path / File name: Click on the “Browse” button to select the desired p ath to save as well as naming the video file.
4. Administrating the Device AirLive FE-200CU Manua l 22 4.2.2 Advanced z White balance: Adjustment to compensate for diff erent envir onments in terms of li ght source. A user can choose auto/hold/sunny/cloudy /indoor , so FE-200CU can determine the correct color compensation due to different light environment.
4. Administrating the Device AirLive FE-200CU Manua l 23 z Infrared (IR) Cut Filter: The default is automatically switched according to the light intensity . “Enable” indicates the filter is enable to cut IR light to make sure t he color is correct.
4. Administrating the Device AirLive FE-200CU Manua l 24 (3) Quad w ith source view: (4) T riple view: 2. Ceiling Mount: For Choosing Ceiling mount, go back to liv e view . There are 6 kinds of video layout to choose from Original view , Broad view , Quad view , Quad with source view , Double view and T riple view .
4. Administrating the Device AirLive FE-200CU Manua l 25 (2.) Broad view: (3.) Quad view: (4.) Quad with source view: (5.) Double view:.
4. Administrating the Device AirLive FE-200CU Manua l 26 (6.) T riple view: 3. 720P W all Mount: For Choosing 720P W all Mount type, go back to Live view . There are 3 kinds of video layout to choose, including Broad view 、 Double view 、 Double with source view .
4. Administrating the Device AirLive FE-200CU Manua l 27 4.3 Event 4.3.1 Event Server z Add FTP Server: Click on the “Add FTP” to exp and FT P server setting.
4. Administrating the Device AirLive FE-200CU Manua l 28 HTTP Server: Name: Give a name for the HTTP server URL: Input the network address of the HTTP server Username / Password: I nput the username and pa ssword of the HTTP . z Remove: Click “Remove” to delete selected event servers.
4. Administrating the Device AirLive FE-200CU Manua l 29 4.3.2 Motion Detection z T o add a motion detection area: 1. Click on “Add” to set up a detection area. (Setup p anel will be expanded) 2. Give a name to this window area. 3. Select the trigger level and sensitivity for this detection window .
4. Administrating the Device AirLive FE-200CU Manua l 30 5. Draw detection window on the image. 6. Once everything is done, click on “Sav e” to save the configuration made. Configured detection window will be displayed in motion detection list. (Circled in blue) Note: 1.
4. Administrating the Device AirLive FE-200CU Manua l 31 4.3.3 I/O Ports AirLive FE-200CU supports 1 photo-coupled re lay inputs and 1 relay output s. Refer to “ Appendix A: I/O T erminal Connectors ” for det ail pin description and application. The below table shows the st atus of t he external trigger/alarm devices.
4. Administrating the Device AirLive FE-200CU Manua l 32 5. The trigger condition is Motion Detection. The responding actions can be “Upload images” and “Act ivate Output Port” and “Send Email Notification” and “Send HTTP Noti fication to” and “Send Message Notification (TCP)”.
4. Administrating the Device AirLive FE-200CU Manua l 33 4.5 Network 4.5.1 General Device IP configuration, in cludes DHCP and S tatic IP setti ng. “Enable ARP/Ping” enables device to accept ARP or ping packets from the network. Disabling this option may provide extra security from intentional ping.
4. Administrating the Device AirLive FE-200CU Manua l 34 Enable this checked box when a DHCP server is installed on the network to issue IP address assignment. With this setting, the IP address is assigned automatically . If this device can not get an IP address within limited tries, the device will assign to the default IP address, 192.
4. Administrating the Device AirLive FE-200CU Manua l 35 4.5.2 Advanced Enable or configure other network functions. z NTP: Configure a NTP (Network T ime Protocol) se rver , so that the device system date and time can be synchronized with a specif ied T ime Server or DHCP server .
4. Administrating the Device AirLive FE-200CU Manua l 36 4.5.4 DDNS (Dynamic DNS) Dynamic DNS configuration. The network device can be assigned with a host name by registering this service (Internet access required).
4. Administrating the Device AirLive FE-200CU Manua l 37 4.6 System 4.6.1 Information Lists - System and Network configurations. z Firmware V ersion: This information shows the firmware version of the device. 4.6.2 User Use this menu to add, update, or remove the usernames and passwords of the Administrator and viewer .
4. Administrating the Device AirLive FE-200CU Manua l 38 The default username and password is adm in/admin respectively . 4.6.3 Day & Time Y ou can setup the device or make it synchronized with PC or remote NTP server . Also, you may select your time zone in order to synchronize time locally .
4. Administrating the Device AirLive FE-200CU Manua l 39 z Reboot: The device is restarted without changing any of the network settings. I t means the IP address of the device will not change after firmware upgrade. z Load Default (Excluding Network setting): The unit is restarted and most current sett ings are reset to fa ctory default values.
4. Administrating the Device AirLive FE-200CU Manua l 40 1. Close all other application programs which are not necessary for firmware update. 2. Make sure that only you access this device while firmware updating. 3. Disable Motion Detection function. 4.
4. Administrating the Device AirLive FE-200CU Manua l 41 4.6.5 Log Service Most system operations and / or process will be kept in a log system. The link provides the review of these records.
4. Administrating the Device AirLive FE-200CU Manua l 42 z Use Custom Settings: The allowed modifications are changing of Background / T e xt Color , Background picture, T itle, Descrip tion, Logo Link and Logo.
5. Appendix AirLive FE-200CU Manua l 43 5 5. Appendix Appendix A: Alarm I/O Connector This Network Camera provides a general I/O terminal block as below: Pin Function Description 1 COM 2 RELA Y -NO Digital output implement ation; Pin2 to COM (Pin1) is a Photo-coupled relay on Normal Open status.
5. Appendix AirLive FE-200CU Manua l 44 Appendix B: T roubleshooting & Frequently Asked Questions Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.264, MPEG4 and JPEG triple compression to providing hi gh quality images.
5. Appendix AirLive FE-200CU Manua l 45 The username and password for the first time or after facto ry default reset Username = admin and Password = airlive . Note that it’ s all case sensitivity . Forgot the username and password To restore factory default, please follow the steps: 1.
5. Appendix AirLive FE-200CU Manua l 46 UPnP NA T T raversal Can not work with NA T router • Maybe NA T router does not support UPnP function. Please check user ’s manual of router and turn on UPnP function. • Maybe UPnP function of NA T router is not comp atible to the IP camera.
5. Appendix AirLive FE-200CU Manua l 47 • Confirm that Default Gateway address is correct. • The router needs Port Forw arding feature. Refer to your router's manual for details. • Packet Filtering of the router may prohibit access from an external network.
5. Appendix AirLive FE-200CU Manua l 48 Internet Explorer displays the following message: “Y our current security settings prohibit downloading ActiveX controls”. Setup the IE security settings or configure the individual settings to allow downloading and scripting of ActiveX controls.
5. Appendix AirLive FE-200CU Manua l 49 • If FTP does not work properly , ask your ISP or network administrator about the transferring mode of FTP server . Pan/T ilt does not work. (including Click to Center and Preset Positioning) • Click [Refresh] on the Internet Explorer when the communication stops with the device.
5. Appendix AirLive FE-200CU Manua l 50 Appendix C: PING IP Address The PING (stands for Packet Internet Gr oper) command is used to detect whether a specific IP address is accessible by sending a packet to the specific address and waiting for a reply .
5. Appendix AirLive FE-200CU Manua l 51 Actual results generated by the device may be varying. Image Resolution A verage range of data sizes for JPEG mode A verage bit rate for MPEG4 mode A verage bit rate for H.
5. Appendix AirLive FE-200CU Manua l 52 Audio Streaming One-way or T wo-way Microphone Built-in Microphone Audio Output Built-in S peaker Network Supported Protocols HTTP, TCP/IP, IPv4, UDP, SMTP, FTP.
5. Appendix AirLive FE-200CU Manua l 53 Sof tware Search & Installation IPWizard II Bundled NVR Program CamPro Express 64, CamPro Professional Appendix F: Configure Port Forwarding Manually The device can be used with a router .
5. Appendix AirLive FE-200CU Manua l 54 you rest art your computer . Y our W AN IP Addre ss will be listed here. Note : Because a dynamic W AN IP can change from time to time d epending on your ISP , you may want to obtain a S t atic IP address from your ISP .
5. Appendix AirLive FE-200CU Manua l 55 • Enter your camera’ s local IP Address (e.g., 192.168.0.100 , for example) in the Private IP field. • If you are using the default camera port settings, enter 80 into the Public and Private Port section, click Apply .
5. Appendix AirLive FE-200CU Manua l 56 Appendix G: DDNS Application z Preface If you have a Cable modem or xDSL, this is a great way to host your own Networked Device or other TCP/IP Service. Ge t your own domain lik e www .yourname.com, www .yourname.
5. Appendix AirLive FE-200CU Manua l 57 (3). Af ter the columns show up at the left side, click “ Create Account ”. (4). Fill the application agreem ent and necessary information. a. Username b. E-mail address and confirmation c. Password and confirmation d.
5. Appendix AirLive FE-200CU Manua l 58 Click these two options (5). Check your e-mail mailbox. There will be an e-mail with a title “Y our DynDNS Account Information“. Click the hyperlink address to confirm the DDNS service that you just applied.
5. Appendix AirLive FE-200CU Manua l 59 Click to confirm (6). Enter the web page http://www .dyndns.org/ again. Input your username and password that you just applied to login adm inistration interface of D DNS server .
5. Appendix AirLive FE-200CU Manua l 60 (8). Click the “ Services ”. (9). Click the “ Dynamic DNS ”. (10). Click the “ Get S ta rted ”..
5. Appendix AirLive FE-200CU Manua l 61 (1 1). We could create a domain name without any c harge at this ste p. First, we input the host name. (Pink No.1) Then we pick a domai n that is easy to remember . (Pink No.2) The 3rd step is to click “Of fli ne Hostname” from Service T ype.
5. Appendix AirLive FE-200CU Manua l 62 Appendix H: Power Line Frequency COUNTRY VOL T AGE FREQUENCY COMMENTS Argentina 220V 50 Hz *Neutral and line wires are reversed from that used in Australia and elsewhere. Australia 230V* 50 Hz *Outlets typically controlled by adjacent switch.
5. Appendix AirLive FE-200CU Manua l 63 Portugal 230V 50 Hz S pain 230V 50 Hz Sweden 230V 50 Hz Switzerland 230V 50 Hz T aiwan 1 10V 60 Hz Thailand 220V 50 Hz United Kingdom 230V* 50 Hz *Outlets typically controlled by adjacent switch. Though nominal voltage has been officially changed to 230V , 240V is within tolerances and commonly found.
5. Appendix AirLive FE-200CU Manua l 64 Appendix J: Enable UPnP of Windows XP Use the following steps to enable UPnP settings only if your operati ng system of PC is running Windows XP .
5. Appendix AirLive FE-200CU Manua l 65 Click Add/Remove Windows Components The following screen will appear: Select Networking Services Click Details.
5. Appendix AirLive FE-200CU Manua l 66 Select Universal Plug and Play Click Ok Click Next.
5. Appendix AirLive FE-200CU Manua l 67 Please wait while Setup configures the components. Click Finish.
Ein wichtiger Punkt beim Kauf des Geräts AirLive FE-200CU (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie AirLive FE-200CU noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für AirLive FE-200CU - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von AirLive FE-200CU reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über AirLive FE-200CU erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon AirLive FE-200CU besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von AirLive FE-200CU verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit AirLive FE-200CU. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei AirLive FE-200CU gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
