Benutzeranleitung / Produktwartung 36-600 des Produzenten DeWalt
Zur Seite of 29
INSTRUCTION MANUAL 10" T able Saw (Model 36-600) P ART NO. 901608 (014) Copyright © 2001 Delta Machinery ESP AÑOL: PÁGINA 29 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 ADDITIONAL SAFETY RULES FOR T ABLE SA WS 1. DO NOT OPERA TE YOUR TOOL until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the opera- tion of circular saws, obtain advice fr om your supervisor , instructor , or other qualified person.
4 CONNECTING TOOL TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wir e and should be protected with a 20 Amp time lag fuse.
Use proper extension cor ds. Make sur e your extension cord is in good condition and is a 3-wir e extension cor d which has a 3-prong gr ounding type plug and a 3-hole r eceptacle which will accept the tool’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the curr ent of the saw .
6 1 - T able Saw 2 - Extension Wing (2) 3 - Rip Fence 4 - Miter Gage 5 - Rip Fence Handle 6 - Handwheel (2) 7 - Handwheel Lock Knob (2) * - Washer (2), Not Shown Used to mount handwheel lock knob Fig. 1 UNP ACKING AND CLEANING Carefully unpack the tool, stand and all loose items fr om the carton.
7 For Blade Guard and Splitter Assembly 1 - Splitter Bracket 2 - 5/8 ″ Flat W asher (2) 3 - M12 Hex Nut (2) 4 - M6 x 20MM Hex Head Scr ew 5 - 1/4 ″ Ext.
8 Fig. 3 For Saw Stand 1 - T op Front and Rear Braces - 19 ″ in length (2) 2 - Bottom Fr ont and Rear Braces - 22-1/2 ″ in length (2) 3 - Stand Legs (4) 4 - Plastic Feet (4) 5 - 3/8 ″ Flat W ash.
9 ASSEMBLING SA W TO ST AND 1. Position the saw (B) on the stand as shown in Fig. 6, lining up the four holes on the bottom of sides of the saw cabinet with the four holes in the two top side braces, one of which is shown at (A). 2. Fasten the saw to the stand using the four 16MM long hex head screws, eight flat washers and four hex nuts supplied.
10 Fig. 7 Fig. 8 Fig. 9 Fig. 10 2. Assemble flat washer (not shown), and lock knob (E) Fig. 8, on end of raising screw shaft. 3. Assemble tilting screw handwheel (F), flat washer (not shown), and lock knob (G) Fig. 8, to the blade tilting screw shaft in the same manner , as shown in Fig.
11 Fig. 11 Fig. 12 Fig. 13 5. Using the open end wrench (F) Fig. 11 and Fig. 12, supplied, place the wrench (F) on the flats on the saw arbor to keep the arbor from turning and tighten arbor nut (E) (turn counterclockwise) using the remaining wrench (G) Fig.
12 Fig. 14 Fig. 15 Fig. 16 Fig. 17 ASSEMBLING GUIDE RAILS 1. Align the three slotted holes in the front guide rail (A) Fig. 14, with two holes (B) in saw table and slotted hole (C) in extension wing.
13 Fig. 18 Fig. 19 Fig. 20 Fig. 21 5. Assemble longer section of rear guide rail (P) Fig. 18, and shorter section of guide rail (R) to extension wings and saw table at points (A) with 16MM long hex head screw (S), two flat washers (T), lockwasher (V), and hex nut (W); and at points (B) and (C) Fig.
14 Fig. 22 Fig. 23 Fig. 24 Fig. 25 LEVELING AND ADJUSTING FRONT GUIDE RAIL 1. MAKE CERT AIN THE TOOL IS DISCONNECTED FROM THE POWER SOURCE. Raise saw blade to its highest level. 2. With handle (A) Fig. 22 in the raised position, place rip fence (B) on the saw table as shown.
15 Fig. 26 Fig. 27 Fig. 29 Fig. 28 5. Check the alignment of the splitter (C) Fig. 29, to the saw blade using a straight edge as shown. If alignment is necessary , loosen nut (B), align splitter (C) and retighten nut (B).
16 F ASTENING ST AND TO SUPPOR TING SURF ACE IF DURING OPERA TION THERE IS ANY TENDENCY FOR THE TOOL TO TIP OVER, SLIDE OR W ALK ON THE SUPPORTING SURF ACE, REMOVE THE RUBBER FEET FROM THE ST AND AND SECURE THE ST AND TO THE FLOOR.
17 ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS Y our saw is equipped with positive stops that will position the saw blade at 90 and 45 degrees to the table. T o check and adjust the positive stops, proceed as follows: 1. DISCONNECT THE TOOL FROM THE POWER SOURCE.
18 Fig. 41 Fig. 42 Fig. 43 RIP FENCE OPERA TION AND ADJUSTMENTS IMPORT ANT : THE RIP FENCE MUST BE PROPERL Y ALIGNED TO THE MITER GAGE SLOT IN ORDER TO PREVENT KICKBACK WHEN RIPPING.
19 Fig. 44 Fig. 45 Fig. 46 Fig. 47 1. Y our miter gage is equipped with individually adjust- able index stops at 90 degrees and 45 degr ees right and left. Adjustment to the index stops can be made by loosening lock nuts (A) Fig. 44, and tightening or loosening the three adjusting scr ews (B) against the stop link (C).
20 20 RIPPING Fig. 48 TYPICAL OPERA TIONS CROSS-CUTTING Cross-cutting r equir es the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 48.
21 21 Fig. 51 Fig. 52 Fig. 53 USING ACCESSOR Y MOULDING CUTTERHEAD Moulding is cutting a shape on the edge or face of the work. Cutting mouldings with a moulding cutterhead in the circular saw is a fast, safe and clean operation.
22 Fig. 58 Fig. 57 Fig. 54 Fig. 55 Fig. 56 The dado head set (D) Fig. 57, is assembled to the saw arbor in the same manner as the saw blade. The guard, splitter and anti-kickback finger assembly cannot be used when dadoing and must be removed fr om the saw .
23 Fig. 59 Fig. 60 USING AUXILIAR Y WOOD F ACING ON RIP FENCE It is necessary when performing special operations such as when using the moulding cutterhead to add wood facing (A) Fig. 59, to one or both sides of the rip fence, as shown. The wood facing is attached to the fence with wood screws thr ough the holes pr ovided in the fence.
24 CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by following the pattern shown in Fig. 61. CUT OFF HERE TO PUSH 1/4 ″ WOOD CUT OFF HERE TO PUSH 1/2 ″ WOOD 1/2 ″ SQUARES NOTCH TO HELP PREVENT HAND FROM SLIPPING Fig.
25 Fig. 62 Fig. 63 Fig. 64 MAINTENANCE CHANGING THE BLADE 1. MAKE CERT AIN THE TOOL IS DISCONNECTED FROM THE POWER SOURCE. USE ONL Y 10 ″ ″ DIAMETER SAW BLADES RA TED FOR 5500 RPM OR HIGHER WITH 5/8" ARBOR HOLES. 2. Raise saw blade to its maximum height and remove the table insert (A) Fig.
26 26 Fig. 65 Fig. 67 Fig. 66 BEL T REPLACEMENT Should you find it necessary to replace the belt on your saw , proceed as follows: 1. DISCONNECT THE TOOL FROM THE POWER SOURCE. 2. Raise the saw blade to its maximum height and remove the blade guar d and splitter , table insert and saw blade.
Delta Building T rades and Home Shop Machinery T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which.
28 NOTES.
The following are trademarks of POR TER-CABLE DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® ,.
Ein wichtiger Punkt beim Kauf des Geräts DeWalt 36-600 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie DeWalt 36-600 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für DeWalt 36-600 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von DeWalt 36-600 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über DeWalt 36-600 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon DeWalt 36-600 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von DeWalt 36-600 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit DeWalt 36-600. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei DeWalt 36-600 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
