Benutzeranleitung / Produktwartung C1060 des Produzenten 3M
Zur Seite of 34
Headset Intercom System Model C1060 Operating Instructions.
.
Model C1060 Table of Contents 3M 2001 February i Intended Use .................................................................................................................................... iii FCC Information ................................
Table of Contents Model C1060 3M 2001 February ii Talk Lock Mode ( “ Hands Free ” ) ...................................................................................................... 10 Page Mode ...........................................
Model C1060 Important Information 3M 2001 February iii Intended Use The 3M Headset Intercom System, Model C1060, is designed to provide 2 –way radio –frequency audio communication in quick service drive –through restaurants and convenience stores.
Important Information Model C1060 3M 2001 February iv (Blank Page).
Model C1060 System Descrip tion 3M 2001 February 1 The 3M Model C1060 Headset Intercom System is a wireless intercom system designed for high reliability, compactness, and ease of service.
System Description Model C1060 3M 2001 February 2 The number of system components and the procedures necessary to operate them vary depending on the system configuration. However, four components are common to all system configurations. The base station is the interface between the customer at the menu sign and the headset worn by the operator.
Model C1060 System Descrip tion 3M 2001 February 3 The programming station is used to program C960 and C1060 headsets to the same channel as the base station. Infrared light is used to transfer program data to the C1060 headset and a separate jack is provided for the C960 headset programming cable.
Controls and Indicators Model C1060 3M 2001 February 4 The base station controls and indicators are shown below. Figure 5. Base Station Controls and Indicators The ON/OFF switch controls power to the base station. This indicator lights when the ON/OFF switch is in the ON position.
Model C1060 Controls and Indicators 3M 2001 February 5 The headset controls are shown below. 1 2 3 4 5 6 7 8 9 10 11 13 12 14 15 Figure 6. Headset Controls Press the switch once to turn on the headset, and press it again (when the headset is on) to turn off the headset Press the volume up control to increase the volume in the headset earpiece.
Controls and Indicators Model C1060 3M 2001 February 6 For dual –lane systems, press and hold the T2 (Talk Lane 2) switch to talk to the customer at the menu sign in lane 2. Release the switch to listen. For single –lane systems, T2 can also be used to talk to lane 1.
Model C1060 Controls and Indicators 3M 2001 February 7 The 3 –slot and 6 –slot battery charger controls are shown below. (Rear View) (Rear View) 1 2 4 1 1 2 2 4 The charging slots hold batteries during the recharging cycle.
Headset Preparation Model C1060 3M 2001 February 8 Adjust the size of the headband until the ear pad rests against one ear and the battery-side pad rests just above the other ear. • Slide the headband out of the headset to make it larger . • Push the headband into the headset to make it smaller .
Model C1060 Operation 3M 2001 February 9 System startup includes turning on the base station and each headset that will be used. To turn on the base station: 1. Slide the power ON/OFF switch to the ON position. Check to see that the POWER indicator lights.
Operation Model C1060 3M 2001 February 10 Communication During Off –Peak Hours During off –peak hours, the cross –lane module is turned on to enable a single operator to communicate with customers in either lane (1 or 2).
Model C1060 Operation 3M 2001 February 11 Use this mode to talk to other operators who are wearing headsets without being heard by the customer at the menu sign. This mode is available with all system configurations. To page another operator, press and hold the page switch.
Operation Model C1060 3M 2001 February 12 ….then press ON / OFF Switch LED indicator turns green?? Press and hold PAGE switch…. Figure 10. Page Switch and On / OFF Switch To respond to a page, press P (page switch). To return to normal headset operation: 1.
Model C1060 Maintenance 3M 2001 February 13 When the battery voltage is too low, the headset sounds a short, low –volume tone at seven –second intervals to alert the operator to install a fully charged battery.
Maintenance Model C1060 3M 2001 February 14 To replace the ear pad, remove the worn/damaged ear pad from the ear cup and replace it with a new pad. See Figure 12. Figure 12. To replace the headband pad, remove the worn/damaged pad by peeling it from the back of the battery housing.
Model C1060 Maintenance 3M 2001 February 15 The battery charger should be placed on a flat surface such as a desktop or table in a clean, dry environment. If the indicators fail to light during charger operation, clean the contacts using an alcohol –moistened cotton swab.
Maintenance Model C1060 3M 2001 February 16 To help protect the environment, C1060 rechargeable batteries which have reached the end of their useful life should be disposed of in accordance with local requirements. Follow these tips to make sure batteries are always ready for use: • Have an extra battery for each headset.
Model C1060 Special Instructions for System Manager 3M 2001 February 17 The headsets are factory programmed for single –lane operation to enable the operator to press either T1 or T2 to communicate with lane 1. For cross –lane systems, the headsets must also be programmed to enable communication with either lane 1 or lane 2.
Special Instructions for System Manager Model C1060 3M 2001 February 18 The talk lock feature provides hands free operation in duplex communication systems. With the talk lock feature enabled, the headset automatically switches from standby to talk/listen when a customer is detected at the menu sign.
Model C1060 Special Instructions for System Manager 3M 2001 February 19 The C1060 system is capable of operating on any one of eight different channels. You can correct these types of interference by changing the base station operating channel. To do this: 1.
Special Instructions for System Manager Model C1060 3M 2001 February 20 Figure 17. 3. Press the RESET switch to “ read ” the new channel selection into the microprocessor. ü Note When two systems are used in a cross –lane application, both base stations must be set to the same channel.
Model C1060 Special Instructions for System Manager 3M 2001 February 21 Figure 18. 4. With the headset turned OFF, swing the microphone back, and insert the headset into the programming station with its programming window facing toward the programming cable jacks.
Special Instructions for System Manager Model C1060 3M 2001 February 22 Day/Night Switch Monitor Volume Access Figure 19. Normally, the VOLUME DAY/NIGHT switch is always left in the DAY position. However, if local ordinances require quieter nighttime operation of the menu sign, move the VOLUME DAY/NIGHT switch to the NIGHT position.
Model C1060 Troubleshooting 3M 2001 February 23 To use the following troubleshooting guide, locate the problem in the left column and look for the problem’s possible causes and corrections in the middle and right columns. Possible causes are listed in the order in which they are most likely to happen.
Troubleshooting Model C1060 3M 2001 February 24 5. All headsets will not go into Standby (silence) when the vehicle leaves the menu sign. 1. This is normal when a pulse (air switch) type of vehicle detector is used. 1. Pres s the Page switch to silence the menu microphone.
Model C1060 Troubleshooting 3M 2001 February 25 7. No Talk or listen from the menu sign when using the backup wired intercom. The C1060 system works OK. 1. The base station is turned on. 2. No power to the backup intercom. 3. The volume controls are set too low on the backup intercom.
Troubleshooting Model C1060 3M 2001 February 26 Battery and Battery Charger Troubleshooting Problem Possible Cause Solution 1. No lights come on when a battery is inserted into charger. 1. Dirty contacts on battery or charger. 1. Clean contacts on battery and charger with an alcohol moistened swab.
Model C1060 Troubleshooting 3M 2001 February 27 Most, if not all, C1060 system service needs can be fulfilled by your local 3M dealer. If special service assistance is needed, however, or for information on how to properly dispose of your non –functional C1060 rechargeable batteries, please call 1 –800 –328 –0033.
3 Food Services Trade Department 3M Center St. Paul, MN 55144-1000 Printed on 50% recycled waste paper, including 10% post-consumer waste paper. Printed in U.
Ein wichtiger Punkt beim Kauf des Geräts 3M C1060 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie 3M C1060 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für 3M C1060 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von 3M C1060 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über 3M C1060 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon 3M C1060 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von 3M C1060 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit 3M C1060. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei 3M C1060 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
