Benutzeranleitung / Produktwartung AR504 des Produzenten Airlink101
Zur Seite of 45
User’s Manual Model # AR504 Ver. 1A.
2 Table of Contents 1. Intr oducti on ................................................................................................................ .3 1.1 Functions and Featur es .....................................................................
3 1. Introduction Congratulations on your purchase of this Br oadband Router. This produc t is specifically designed for Small Office and Home Office needs. It provides a complete SOHO solution for Internet surfing and is easy to configure and operate ev en for non-technical users.
4 Security Functions • Packet Filter Supported Packet Filter allows you to control access to a network by analyzing the incoming and outgoing packet s and allowing or denying them access based on the IP address of the source and destination.
5 2. Hardware Inst allation 2.1 Connect the Router Note : Prior to connecting the router, be sure to power off your computer, DSL/Cable modem, and the router. Step 1 Connect one end of a network cable to the WAN port of the router and connect the other end of the cabl e to the DSL/Cable modem.
6 2.2 LED Description LED Function Color St atus Description POWER Power indication Green On Device is powered on. S tatus System status indication Orange Blinking M1 flashes once per second to indicate system is active. M2 is lit when system is busy .
7 2.3 Verify Connection to Router Step 1 Go to Start , Run , type command (for Windows 95/98/ME) or cmd (for Windows 2000/XP) and click OK . You will see the command prompt as below. Step 2 Type ping 192.168.1.1 and press Enter . You should get four reply responses back.
8 Step 5 Type ipconfig/renew and press Enter . You should get an IP address of 192.168.1.x (where x is a number between 2 - 254). Proceed to Section 3, Configure the Router. If you don’t get an IP address, reset the router by holding in the reset button at the back of the router for 10 seconds while it is ON and try ipconfig/renew again.
9 Step 8 After your IP addre ss is released, click Renew . You should get an IP address of 192.168.1.x (where x is a number between 2 - 254). If you don’t get an IP address, reset the router by holding in the reset butto n at the back of the ro uter for 10 seconds while it is ON and try Renew again.
10 3. Configure the Router 3.1 Setup Wizard Step 1 Open the web browser and type 192.168.1.1 in the URL Address field and press Enter . Step 2 Enter admin for the password field and click Log in . Step 3 Click on Wizard from the main menu to open the Setup Wizard.
11 Static IP If your ISP provided you with a static IP address, select ISP assigns you a static IP address (Static IP Address) and click Next . Proceed to Step 6, Static IP . Cable Modem If you use cable modem, select Obtain an IP address from ISP automatically (Dynamic IP Address) and click Next .
12 Static IP Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7 . Cable Modem If your ISP has provided you with a host name, enter it in the Host Name field. If your ISP requires a registered MA C Address, click on the Clone MAC button.
13 Road Runner Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7 . DSL Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7 .
14 PPTP Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7 . L2TP Fill in the applicable fields according to the information provided by your ISP. Click Next when done and proceed to Step 7 .
15 Step 7 Click Reboot to apply your settings. Step 8 Click OK to confirm reboot. Step 9 Wait for the router to reboot and proceed to Section 4, Verify Connection Status .
16 4. V erify Connection S t atus 4.1 Checking the System Status View the System Status to ve rify your Internet connection. Step 1 Login to the router’s web configuration page and click on the Status link from the Main Menu. Step 2 Verify that the WAN Status displays valid numbers (instead of all 0’s).
17 Step 3 Once you clicked the Renew or Connect button, you should see some numbers under WAN Status . This means you have successfully established Internet connection. Note: If you still see all 0’s after clicking on the Renew or Connect button, try the troubleshooting tips at the end of this manual.
18 5. W eb Configuration 5.1 Accessing the Web Configuration Utility You may configure the router through the web browser us ing the Web Configuration Utility. Step 1 Open the web browser and type in 192.168.1.1 and press Enter . Step 2 Enter admin for the password field and click Log in .
19 5.2 Basic Setting 5.2.1 Primary Setup You can set the router’s LAN IP addr ess and change the WAN type (Internet Connection Type) on this page. LAN IP Address: The router’s default IP address is 192.168.1.1 . You can change this address to suit your existing network.
20 Host Name (optional): Some ISPs require a register ed host name to connect to their services. Enter the host name prov ided by your ISP, if applicable. WAN’s MAC Address: Some ISPs require a regist ered MAC address to connect to their services. Either manually enter the MAC address or click the Clone MAC button.
21 Enter the Account name and Password required to connect to your ISP. Some ISPs require an additional Login Server . Renew IP Forever: Checking the Enable box will allow the rout er to automatically renew the IP address automatically when the lease time is expired.
22 Enter the information provided by your ISP in the respective fields. Connection ID (optional): Some ISPs require the use of a connection ID. Maximum Idle Time (in seconds): Enter the maximum idle time (in seconds) before the router disconnects the PPPoE session.
23 Enter the information provided by your ISP in the respective fields. Maximum Idle Time (in seconds): Enter the maximum idle time (in seconds) before the router disconnects the PPPoE session. Auto-reconnect (check box): Checking this box enables the router to automatically reconnect to the Internet once the connection is dropped.
24 5.2.2 DHCP Server This page allows you to configure the DHC P service of the router. DHCP assigns dynamic IP address to all the network devices connected to the router. DHCP Server: Select either to Enab le or Disable the DHCP service (Default is Enable ).
25 Clients List The Clients List displays all the DHCP cli ents currently connected to the router. To perform the first two functions, se lect a client from the list first. Wake up: Sends a wake up packet to the target client. The target client must support the wake up function.
26 Old Password: Enter the current login password. New Passw ord: Enter the new login password. Reconfirm: Enter the new login password again. Click Save to save any changes or click Undo to cancel any changes.
27 Enable (check box): Check on this box to open the port. Use Rule# (optional): Enter the Schedule Rule # you wis h to apply to the ID. For more information about using the Schedule Rule #, please see 5.
28 Popular applications: Select from a list of popular applications. Copy to (button): Select the ID # (1 ~ 8) you want to paste the port numbers to first and then click on this button to paste t he port numbers to the applicable fields. Click Save to save any changes or click Undo to cancel any changes.
29 5.4 Security Setting 5.4.1 Packet Filter Packet Filter enables you to control which packets are allowed to pass through the router. Outbound filter applies on all outbound packets. However, Inbound filter applies to packets that are destined to Vi rtual Servers or DMZ host only.
30 For source or destination IP address, you can define a single IP address (192.168.1.100) or a range of IP addresses (192.168.1.1001- 192.168.1.254). An empty field implies all IP addresses. For source or destination port, you can defi ne a single port (80) or a range of ports (1000-1999).
31 5.4.2 Domain Filter Domain Filter lets you prevent user s from accessing any specified domain. Domain Filter: Check the Enable box to activate the Domain Filter function. Log DNS Query: Check the Enable box to log the action of someone trying to access the specified domain.
32 5.4.3 URL Blocking URL Blocking will block the lo cal computers from accessi ng pre-defined web sites. The main difference between Domain filter and URL Blocking is that Domain filter requires you to input a suffix like .com or .org, etc., while URL Blocking only requires you to input a keyword.
33 5.4.4 MAC Address Control MAC Address Control allows you to assign di fferent access rights for different users and to assign a specific IP address to a certain MAC address. MAC Address Control: Check the Enable box to activate the MAC Address Control function.
34 5.4.5 Miscellaneous Items Remote Administrator Host/Port: In general, only local users can browse the router’s built-in web configuration utility to perform administration tasks. Re mote Administration enables you to perform administr ative tasks from remote host.
35 5.5 Advanced Settings 5.5.1 System Time This page allows you to configure the system time of your router. Get Date and Time by NTP Protocol: Select this option if you want to obtain the time from a Network Time Server. Time Server: Select the time server you want to sync with.
36 5.5.2 System Log This page allows you to export the system lo gs to specific destination by means of syslog (UDP) and SMTP (TCP). IP Address for Syslog: Enter the destination IP Addre ss where the syslog will be sent to. Be sure to check the Enable box.
37 5.5.3 Dynamic DNS Dynamic DNS allows any user who wishes to access your server to reach it by a registered DNS name instead of an IP address. Before you enable Dynamic DNS , you need to register an account with one of t he Dynamic DNS servers listed in the Provider field.
38 5.5.4 Routing The Routing Table allows you to set wh ich network interface address to use for outgoing IP data grams. If you have mo re than one router and subnet, you will need to configure the routing table to direct the packets to follo w the proper routing path so different subnets can communicate with each other.
39 5.5.5 Schedule Rule The Schedule Rule allows you to set the ti me when certain services will be on or off. Schedule Rule works in conjunction with Virt ual Server and Packet Filter to determine when these services will be active or inactive. Schedule : Check the Enable box to activate the Schedule Rule function.
40 Click Save to save any changes or click Undo to cancel any changes. Once you have created the new rule, you can ca ll up this rule from the Virtual Server and Packet Filter page and apply the schedule rule to any IDs in the Virtual Server or Packet Filter page.
41 5.6 Toolbox 5.6.1 View Log This page allows you to view the System Log. Back : Returns to the previous page. Refresh : Updates the log. Download : Saves the log to a specified loca tion.
42 5.6.2 Firmware Upgrade This page allows you to updat e the router’s firmware. 1. Download the latest firmware from the manufacturer’s web site. 2. Click the Browse button to locate the firmware. Be sure to unzip the file first. 3. Click on Upgrade .
43 5.6.3 Backup Setting Once you have configured all of the router’s settings, you can backup the settings as a file on your hard drive. (The file will be named config.bin ). When you want to restore the saved settings, go to the firmwa re upgrade page and browse to the config.
44 5.6.6 Miscellaneous Items Wake-on-LAN is a technology that enables you to power up a network device remotely. In order to use this feat ure, the target device must be Wake-on-LAN enabled and you have to know the MAC address of t he device, i.e. 00-11-22-33-44-55.
45 For DSL Users Only Step 1 Go to the router’s Setup Wizard. Step 2 At the PPPoE setting, double-check t he spelling of your Account name and Password . Some ISPs require you to include the domain name along with your account name in the Account Name field.
Ein wichtiger Punkt beim Kauf des Geräts Airlink101 AR504 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Airlink101 AR504 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Airlink101 AR504 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Airlink101 AR504 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Airlink101 AR504 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Airlink101 AR504 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Airlink101 AR504 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Airlink101 AR504. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Airlink101 AR504 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
