Benutzeranleitung / Produktwartung N5110 des Produzenten Dell
Zur Seite of 90
Dell™ Inspiron™ N5110 Service Manual Regulatory model: P17F Regulatory type: P17 F001.
Notes, Cautions, and W arnings NOTE: A NOTE indicates important information that helps you make b etter use of your computer . CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WAR N IN G : A WARNING indicates a potential for property damage, personal injury , or death.
Contents 3 Contents 1 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . 9 Recommended T ools . . . . . . . . . . . . . . . . . . . . 9 T urning Off Y our Computer . . . . . . . . . . . . . . . . . 9 Before W orking Inside Y our Computer . . . .
4 Contents Replacing the Memory Module(s) . . . . . . . . . . . . 20 6 Optical Drive . . . . . . . . . . . . . . . . . . . . . 23 Removing the Optical Drive . . . . . . . . . . . . . . . 23 Replacing the Optical Drive . . . . . . . . . . . . . . . 24 7 Keyboard .
Contents 5 Removing the Display Bezel . . . . . . . . . . . . 44 Replacing the Display Bezel . . . . . . . . . . . . 45 Display Panel . . . . . . . . . . . . . . . . . . . . . . 46 Removing the Display Panel . . . . . . . . . . . . 46 Replacing the Display Panel .
6 Contents 14 Sy stem Board . . . . . . . . . . . . . . . . . . . . . 65 Removing the Sy stem Board . . . . . . . . . . . . . . . 65 Replacing the Sy stem Board . . . . . . . . . . . . . . . 66 Entering the Service T ag in the BIOS . . . . . . . . . .
Contents 7 19 I/O Board . . . . . . . . . . . . . . . . . . . . . . . . . 83 Removing the I/O Board . . . . . . . . . . . . . . . . . 83 Replacing the I/O Board . . . . . . . . . . . . . . . . . 84 20 VGA/Power Board . . . . . . . . . . . . . . . . . .
8 Contents.
Before Y ou Begin 9 1 Before Y ou Begin This manual provides proced ures for removing and installing components in your computer . Unless otherwise noted, each procedure assumes that the following con.
10 Before Y ou Begin Before W orking Inside Y our Computer Use the following safety guidelines to he lp protect your computer from potential damage and to help to ensure your own personal safety . WAR N IN G : Before working inside your comput er , read the safety information that shipped with your computer .
Before Y ou Begin 11 CAUTION: T o help prevent damage to the sy stem board, remove the main battery (see "Removing the Battery" on page 15) before working inside the computer . 7 Remove the battery (see "Removing the Battery" on page 15).
12 Before Y ou Begin.
T op Cover 13 2 T op Cover WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.com/regulatory_compliance.
14 T op Cover Replacing the T op Cover 1 F ollow the instructions in "Before Y ou Begin" on page 9. NOTE: Ensure that the DELL logo is facing towa rds the back of the comp uter while replacing the top cover . 2 Align the top cover to the display back cover .
Battery 15 3 Battery WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.com/regulatory_compliance.
16 Battery Replacing the Battery 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Slide the battery into the battery bay until it clicks into place.
Module Cover 17 4 Module Cover WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.com/regulatory_compliance.
18 Module Cover Replacing the Module Cover CAUTION: T o avoid damage to the computer , use only the battery designed for this particular Dell computer . 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Align the tabs on the module cover wi th the slots on the computer base and snap the module cover into place.
Memory 19 5 Memory Module(s) WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.com/regulatory_compliance.
20 Memory Replacing the Memory Module(s) CAUTION: If you need to install memory m odules in two connectors, install a memory module in the connector labeled “D IMM A” before you install a memory module in the c onnector labeled “DIMM B.” 1 F ollow the instructions in "Before Y ou Begin" on page 9.
Memory 21 4 Replace the module cover (see "Replaci ng the Module Cover" on page 18). 5 Replace the battery (see "Replacing the Battery" on pa ge 16), or connect the AC adapter to your comput er and an electrical outlet.
22 Memory.
Optical Drive 23 6 Optical Drive WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.com/regulatory_compliance.
24 Optical Drive Replacing the Optical Drive 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Slide the optical-drive assembly into th e optical-drive bay until it is fully seated. 3 Replace the module cover (see "Repla cing the Module Cover" on page 18).
Optical Drive 25.
26 Optical Drive.
Keyboard 27 7 Keyboard WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.com/regulatory_compliance.
28 Keyboard CAUTION: The keycaps on the keyboard ar e fragile, easily dislodged, and time-consuming to replace. Be careful when removing and handlin g the keyboard. CAUTION: Be extremely careful whe n removing an d handling the keyboard. Failure to do so could result in scratching the display panel.
Keyboard 29 Replacing the Keyboard 1 F ollow the instructions in "B efor e Y ou Begin" on page 9. 2 Slide the keyboar d cable into the conn ector on the system boar d and press down on the connector la tch to secure the cable. 3 Slide the tabs on the k eyboard into th e slots on the palm-r est assembly and lower the keyboar d into place.
30 Keyboard 6 Replace the battery (see "Re pla cing the Battery" on page 16)..
Palm-Rest Assembly 31 8 Palm-Rest Assembly WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.
32 Palm-Rest Ass embly 4 T urn the computer over and open the display as far as possible. 5 Remove the keyboar d (see "Removing the Keyboar d" on page 27). 6 Remove the four screws on the palm-rest assembly . CAUTION: Pull on the plastic tab on top of the connectors to avoid damaging the connectors.
Palm-Rest Assembly 33 CAUTION: Carefully separate the palm rest fr om the computer base to avoid damage to the palm rest. 8 Using a plastic scribe, carefully pry out the palm-rest as sembly along the rear edge and then ease the palm-r est assembly from the computer base 9 Lift the palm-rest assembly off the computer base.
34 Palm-Rest Ass embly Replacing the Palm-Rest Assembly 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Align the tabs on the palm r est asse mbly with the slots on the computer base and gently snap the palm r est assembly in place.
Palm-Rest Assembly 35 6 Close the display and tu rn the computer over . 7 Replace the six screws that secure th e palm-r est assembly to the computer base.
36 Palm-Rest Ass embly.
Wireless Mini-Card(s) 37 9 Wireless Mini-Card(s) WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at www .
38 Wireless Mini-Card(s) b Disconnect the antenn a cables from the Mini-Card. c Remove the screw that secur es th e Mini-Card to the system boar d. d Lift the Mini-Card out of the system-board connector .
Wireless Mini-Card(s) 39 Replacing the Mini-Card(s) 1 F ollow the instructions in "B efor e Y ou Begin" on page 9. 2 Remove the new Mini-Card from its packaging. CAUTION: Use firm and even pressure to sli de the card into place. If you use excessive force, you may damage the connector .
40 Wireless Mini-Card(s) F ollow the instructions from step 4 to step 8 in "Replacing the P alm-Rest Assembly" on page 34. 8 Replace the battery (see "Re pla cing the Battery" on page 16). CAUTION: Before turning o n the computer , r eplace all screws and ensure that no stray screws remain inside the computer .
Display 41 10 Display WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.com/regulatory_compliance.
42 Display 4 F ollow the instructions from step 3 to step 9 in "Removing the P alm-Rest Assembly" on page 31. 5 Disconnect the display cable and touch-screen cable from the system-board connectors. NOTE: The touch-screen board is optional and may not be present in your computer .
Display 43 Replacing the Display Assembly 1 F ollow the instructions in "B efor e Y ou Begin" on page 9. 2 Place the display assembly in position and replace the four screws that secure the display assembly to the computer base. 3 Route the Mini-Card antenna cabl es through the routing guides.
44 Display 5 Connect the display cable and touch-screen cable to the connectors on the system boar d. 6 F ollow the instructions from step 2 to step 7 in "Replacing the P alm-Rest Assembly" on page 34. 7 Replace the two screws that secur e th e display assembly to the computer base.
Display 45 Replacing the Display Bezel 1 F ollow the instructions in "B efor e Y ou Begin" on page 9. 2 Realign the display b ezel over the dis play panel and g ently snap it into place. 3 Replace the display assemb ly (see "R eplacing the Display Ass embly" on page 43).
46 Display Display Panel Removing the Display Panel 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Remove the display assembly (see "R emoving the Display Assembly" on page 41). 3 Remove the display bezel (see "Removing the Display Bezel" on page 44).
Display 47 7 Make a note of the display cable and Mini-Card antenna cables routing and remove them from the routing guides on the display back cover . 8 T urn the display panel over and place i t on a clean surface. 9 Remove the display cable (see "Removing the Display Cable" on page 48).
48 Display 6 Align the screw holes on the display panel with the screw holes on the display back cover and replace the eight screws. 7 Replace the display bezel (see "Repla cing the Display Beze l" on page 45). 8 Replace the display assemb ly (see "Replacing the Displ ay Assembly" on page 43).
Display 49 Replacing the Display Cable 1 F ollow the instructions in "B efor e Y ou Begin" on page 9. 2 Connect the display cable to the display-board connector and secure it with the tape. 3 Replace the display panel (see "Replaci ng the Display P anel" on page 47).
50 Display Display-Panel Brackets Removing the Display-P anel Brackets 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Remove the display assembly (see "R emoving the Display Assembly" on page 41). 3 Remove the display bezel (see "Removing the Display Bezel" on page 44).
Display 51 2 Align the screw holes on the display-pa nel brack et with the screw holes on the display panel and replace the four screws (two on each side). 3 Replace the display panel (see "Replaci ng the Display P anel" on page 47). 4 Replace the display bezel (see "Replacing the Display Bezel" on page 45).
52 Display.
Hinge Cover 53 11 Hinge Cover WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance.
54 Hinge Cover 6 Lift the hinge cover off the computer base. 1 screws (4) 2 tabs (7) 1 2 1.
Hinge Cover 55 Replacing the Hinge Cover 1 F ollow the instructions in "B efor e Y ou Begin" on page 9. 2 Align the seven tabs on the hinge c over with the slots on the computer base and snap the hinge cover into place . 3 Replace the four screws that secur e the hinge cover to the computer base.
56 Hinge Cover.
Camera Module 57 12 Camera Module WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at www .dell.com/regulatory_compliance.
58 Camera Module Replacing the Camera Module 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Use the alignment posts on the displa y back cover to place the camera module in position and adhere it in place. 3 Replace the display panel (see "Replaci ng the D isplay P anel" on page 47).
Camera Module 59.
60 Camera Module.
Coin-Cell Battery 61 13 Coin-Cell Battery WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at www .
62 Coin-Cell Battery Replacing the Coin-Cell Battery 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 W ith the positive side up, snap th e coin-cell batter y into the battery socket on the system board. 3 F ollow the instructions from step 2 to step 7 in "Replacing the P alm-Rest Assembly" on page 34.
Coin-Cell Battery 63 CAUTION: Before turning on the computer , replace all screws and ensure that no stray screws remain inside the computer . Failure to do so may result in damage to the computer .
64 Coin-Cell Battery.
Sy stem Board 65 14 Sy stem Board WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.com/regulatory_compliance.
66 Sy stem Board 10 Disconnect the speaker cable from the connector on the system board. 11 Remove the five screws that secure th e system boar d to the computer base. 12 Lift the system board assembly to disconnect the connector on the system board from the connector on the I/O board.
Sy stem Board 67 Replacing the Sy stem Board 1 F ollow the instructions in "B efor e Y ou Begin" on page 9. 2 Replace the processor module (see "R eplacing the Processor Module" on page 80). 3 Replace the thermal cooling as sembly (see "Replaci ng the Thermal-Cooling Assembly" on page 76).
68 Sy stem Board 18 Enter the service tag (see "Ente ring the Service T ag in the BIOS" on page 68). Entering the Service T ag in the BIOS 1 Ensure that the A C adap ter is plugged in and th at the main battery is installed properly . 2 T urn on the computer .
Speakers 69 15 Speakers WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at www .dell.com/regulatory_compliance.
70 Speakers Replacing the Speakers 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Place the speakers on the computer base and route the speaker cable through the routing guides. 3 F ollow the instructions from step 2 to step 17 in "Replacing the System Board" on page 67 .
Hard Drive 71 16 Hard Drive WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at www .dell.com/regulatory_compliance.
72 Hard Drive 4 Slide the hard-drive assembly to di sconnect it from the system-board connector . 5 Lift the hard-drive assembly off the system boar d. 6 Remove the four scr ews that secur e the har d drive to the har d-drive bracket. 7 Lift the hard drive away from the hard-drive bra cket.
Hard Drive 73 Replacing the Hard Drive 1 F ollow the instructions in "B efor e Y ou Begin" on page 9. 2 Remove the new hard drive from its packaging. Save the original packaging for st oring or shipping the hard drive. 3 Place the hard drive in the hard-drive brack et.
74 Hard Drive CAUTION: Before turning o n the computer , r eplace all screws and ensure that no stray screws remain inside the computer . Fa ilure to do so may result in damage to the computer .
Thermal-Cooling Assembly 75 17 Thermal-Cooling Assembly WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at www .
76 Thermal-Cooling Assembly Replacing the Therma l-Cooling Assembly 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Align the screw holes on the therma l-cooling assembly with the screw holes on the system boar d. 3 Tighten the five scr ews that secure the thermal-cooling assembly to the system boar d.
Thermal-Cooling Assembly 77 CAUTION: Before turning on the computer , replace all screws and ensure that no stray screws remain inside the computer . Failure to do so may result in damage to the computer .
78 Thermal-Cooling Assembly.
Processor Module 79 18 Processor Module WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Home page at dell.
80 Processor Module Replacing the Processor Module 1 F ollow the instructions in "Before Y ou Begin" on page 9. NOTE: If a new processor is installed, y ou will receive a new thermal-cooling.
Processor Module 81 When the processor module is properly seated, all four corners are aligned at the same height. If one or more corners of the modul e are higher than the others, the module is not seated properly . CAUTION: T o avoid damage to the processor , hold the screwdriver perpendicular to the processor when turning the cam screw .
82 Processor Module.
I/O Board 83 19 I/O Board WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at dell.com/regulatory_compliance.
84 I/O Board Replacing the I/O Board 1 Slide the connectors on the I/O boar d into the slots on the computer base and place the I/O board on the computer base. 2 Replace the two screws that secur e the I/O board to the computer base. 3 Replace the Mini-Card(s) (see "Repla cing the Mini-Card( s)" on page 39).
VGA/Power Board 85 20 VGA/Power Board WAR N IN G : Before working inside your computer , read the safety information that shipped with your computer . For additiona l safety best practices information, see the Regulatory Compliance Homepage at www .dell.
86 VGA/Power Board Replacing the VGA/Power Board 1 F ollow the instructions in "Before Y ou Begin" on page 9. 2 Align the connectors on the VGA/P owe r board with the slots on the base cover and place it on the base cover . 3 Replace the hinge cover (see "Repla cing the Hinge Cover " on page 55).
VGA/Power Board 87.
88 VGA/Power Board.
Flashing the BIOS 89 21 Flashing the BIOS The BIOS may require flashing when an update is avai lable or when replacing the system board. T o flash the BIOS: 1 T urn on the computer .
90 Flashing the BIOS 8 Double-click the fil e icon on the desktop and follow the instructions on the screen..
Ein wichtiger Punkt beim Kauf des Geräts Dell N5110 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dell N5110 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dell N5110 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dell N5110 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dell N5110 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dell N5110 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dell N5110 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dell N5110. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dell N5110 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
