Benutzeranleitung / Produktwartung M620 des Produzenten Dell
Zur Seite of 133
Dell PowerEdge M620 Systems Owner's Manual Regulatory Model: HHB Regulatory Type: HHB003.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents Notes, Cautions, and Warnings ...................................................................................................2 1 About Your System............................................................................................
Entering The iDRAC Settings Utility .................................................................................................................. 23 3 Installing Blade Components ...................................................................
Installing A Hard Drive/SSD In A Hard-Drive/SSD Carrier ............................................................................... 51 Hard-Drive/SSD Backplane .......................................................................................
System Error Messages ..........................................................................................................................................73 Warning Messages .......................................................................
1 About Your System Front-Panel Features And Indicators Figure 1. Front-Panel Features and Indicators 1. blade handle release button 2. hard drives (2) 3.
Hard-Drive/SSD Indicator Patterns The hard-drive/SSD indicators display different patterns as drive events occur in the system. NOTE: The blade must have a hard drive/SSD or a hard-drive blank installed in each drive bay. Figure 2. Hard-Drive/SSD Indicators 1.
• The Getting Started Guide provides an overview of system features, setting up your system, and technical specifications. • The Rack Installation Instructions included with your rack solution describes how to install your system into a rack.
10.
2 Using The System Setup And Boot Manager System Setup enables you to manage your system hardware and specify BIOS-level options. The following keystrokes provide access to system features during startup: Keystroke Description <F2> Enters the System Setup.
NOTE: Operating systems must be UEFI-compatible to be installed from the UEFI boot mode. DOS and 32-bit operating systems do not support UEFI and can only be installed from the BIOS boot mode. NOTE: For the latest information on supported operating systems, see dell.
Menu Item Description iDRAC Settings This option is used to view and configure iDRAC settings. Device Settings This option is used to view and configure device settings. System BIOS Screen NOTE: The options for System Setup change based on the system configuration.
Menu Item Description System Manufacturer Contact Information Displays the contact information of the system manufacturer. Memory Settings Screen Menu Item Description System Memory Size Displays the amount of memory installed in the system. System Memory Type Displays the type of memory installed in the system.
Menu Item Description can disable this option for applications that require high utilization of random memory access. Hardware Prefetcher Allows you to enable or disable hardware prefetcher. By default, the Hardware Prefetcher option is set to Enabled .
Menu Item Description If the operating system supports UEFI, you can set this option to UEFI. Setting this field to BIOS allows compatibility with non-UEFI operating systems. By default, the Boot Mode option is set to BIOS . NOTE: Setting this field to UEFI disables BIOS Boot Settings menu.
Menu Item Description Slot Disablement The Slot Disablement feature controls the configuration of mezzanine cards installed in the specified slots. Only mezzanine card slots that are present on your system are available for control.
Menu Item Description Monitor/Mwait Allows you to enable Monitor/Mwait instructions in the processor. By default, the Monitor/Mwait option is set to Enabled for all system profiles, except Custom . NOTE: This option can be disabled only if the C States option in Custom mode is disabled.
Menu Item Description NOTE: BIOS updates using Dell Update Package is not affected by this option. Power Button Allows you to enable or disable the power button on the front of the system. By default, the Power Button option is set to Enabled . AC Power Recovery Allows you to set how the system reacts after AC power is restored to the system.
Assigning A System And/Or Setup Password NOTE: The password jumper enables or disables the System Password and Setup Password features. For more information on the password jumper settings, see System Board Jumper Settings.
NOTE: You can use the Password Status option in conjunction with the System Password and Setup Password options to protect your system from unauthorized changes.
• Add, delete, and arrange boot options • Access System Setup and BIOS-level boot options without rebooting To enter the Boot Manager: 1. Turn on or restart your system.
UEFI Boot Menu Menu Item Description Boot From File Sets a one-time boot option not included in the boot option list. Select UEFI Boot Option Displays the list of available UEFI boot options (marked with asterisks), select the boot option you wish to use and press <Enter>.
24.
3 Installing Blade Components Recommended Tools You may need the following items to perform the procedures in this section: • #1 and #2 Phillips screwdrivers • T8 and T10 Torx drivers • Wrist grounding strap Removing And Installing A Blade CAUTION: Many repairs may only be done by a certified service technician.
Figure 3. Removing or Installing the Blade 1. blade handle 2. release button 3. blade 4. guide rail on enclosure 5. guide rail on blade (or blade blank) Installing The Blade 1. If you are installing a new blade, remove the plastic cover from the I/O connector(s) and save for future use.
Opening And Closing The Blade Opening The Blade CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Closing The Blade 1. Ensure that no tools or parts are left inside the blade. 2. Align the notches in the edges of the chassis with the cover alignment pins on the inner sides of the cover. 3. Lower the cover onto the chassis. 4. Slide the cover until it clicks into position.
Cooling Shroud The cooling shroud covers the memory modules and directs air flow in the system. Removing The Cooling Shroud CAUTION: Many repairs may only be done by a certified service technician.
Installing The Cooling Shroud CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
DIMM Type DIMMs Populated/ Channel Operating Frequency (in MT/s) Maximum DIMM Rank/ Channel 1.5 V 1.35 V 3 1333, 1066, and 800 1066 and 800 Dual rank LRDIMM 1 1333 and 1066 1333 and 1066 Quad rank 2 1333 and 1066 1333 and 1066 Quad rank 3 1066 1066 Quad rank Figure 7.
General Memory Module Installation Guidelines NOTE: Memory configurations that fail to observe these guidelines can prevent your system from starting and producing any video output, hanging during memory configuration, or operating with reduced memory.
NOTE: x4 and x8 DRAM based DIMMs can be mixed providing support for RAS features. However, all guidelines for specific RAS features must be followed. x4 DRAM based DIMMs retain Single Device Data Correction (SDDC) in memory optimized (independent channel) mode.
NOTE: 1R, 2R, and 4R in the following tables indicate single-, dual-, and quad-rank DIMMs respectively. Table 1. Memory Configurations – Single Processor System Capacity (in GB) DIMM Size (in GB) Nu.
Table 2. Memory Configurations – Two Processors System Capacity (in GB) DIMM Size (in GB) Number of DIMMs Organization and Speed DIMM Slot Population 16 2 8 1R x8, 1333 MT/s 1R x8, 1600 MT/s A1, A2,.
System Capacity (in GB) DIMM Size (in GB) Number of DIMMs Organization and Speed DIMM Slot Population 384 16 24 2R x4, 1333 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11, A12, B1, B2, B3, B4, B5, .
Figure 8. Installing and Removing a Memory Module or Memory Module Blank 1. memory module or memory blank 2. edge connector 3. ejectors (2) 4. socket 5. alignment key Installing Memory Modules WARNING: The memory modules are hot to the touch for some time after the system has been powered down.
CAUTION: Handle each memory module only on either card edge, making sure not to touch the middle of the memory module. 6. Align the memory module's edge connector with the alignment key on the memory module socket, and insert the memory module in the socket.
NOTE: Hold the mezzanine card by its edges only. 4. Lift the mezzanine card up and away from the system board. 5. Close the retention latch. 6. Close the blade. 7. Install the blade in the enclosure. Figure 9. Installing and Removing a Mezzanine Card 1.
5. Mezzanine cards are designed to fit in either card slot. Rotate the card to align the connector on the bottom of the mezzanine card with the corresponding socket on the system board. 6. Lower the card into place until it is fully seated and the plastic clip on the outer edge of the card fits over the side of the blade chassis.
Figure 10. Replacing the SD Card 1. SD card 2. management riser card 3. USB connector 4. SD card slots Internal USB Key The blade provides an internal USB connector for a USB flash memory key. The USB memory key can be used as a boot device, security key, or mass storage device.
6. Close the blade. 7. Install the blade in the enclosure. 8. Enter the System Setup and verify that the USB key is detected by the system. Figure 11. Replacing the USB Memory Key 1. USB memory key connector 2. USB memory key SD vFlash Card Replacing The SD vFlash Card 1.
2. SD vFlash card slot Network Daughter Card/LOM Riser Card Removing The Network Daughter Card/LOM Riser Card CAUTION: Many repairs may only be done by a certified service technician.
Installing The Network Daughter Card/LOM Riser Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Figure 14. Installing and Removing a Heat Sink 1. screws (4) 2. heat sink 6. Use a clean, lint-free cloth to remove any thermal grease from the surface of the processor shield. CAUTION: The processor is held in its socket under strong pressure. Be aware that the release lever can spring up suddenly if not firmly grasped.
Figure 15. Processor Shield Opening and Closing Lever Sequence 1. OPEN 1st label 2. open first lever 3. processor 4. close first lever 5. CLOSE 1st label 9. Hold the tab on the processor shield and rotate it upward and out of the way. 10. If applicable, remove the socket protective cap from the processor shield.
Figure 16. Installing and Removing a Processor 1. socket-release lever 2 2. pin-1 corner of processor 3. tabs (2) 4. processor shield 5. socket protective cap 6.
Installing A Processor CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
NOTE: Do not over-tighten the heat sink retention screws when installing the heat sink. To prevent over-tightening, tighten the retention screw until resistance is felt, and stop once the screw is seated. The screw tension should be no more than 6 in-lb (6.
Figure 17. Removing and Installing a Hard Drive/SSD 1. release button 2. hard drive/SSD 3. hard-drive/SSD connector (on backplane) 4. hard-drive/SSD carrier handle Installing A Hard Drive/SSD CAUTION: When a replacement hot-swappable hard drive/SSD is installed and the blade is powered on, the drive automatically begins to rebuild.
CAUTION: If you need to power off the blade to service a hard drive/SSD, wait 30 seconds after the blade’s power indicator turns off before removing the hard drive/SSD. Otherwise, the hard drive/SSD may not be recognized after it is reinstalled and the blade is powered on again.
Hard-Drive/SSD Backplane Removing The Hard-Drive/SSD Backplane CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
1. guide pins (3) 2. guides (3) 3. hard-drive/SSD backplane 4. hard-drive/SSD connectors (2) 5. hard-drive backplane/SSD connector Installing The Hard-Drive/SSD Backplane 1. Open the blade. 2. Align the guides on the hard-drive/SSD backplane with the guide pins on the system board.
12. Remove the storage controller card/PCIe extender card. Figure 20. Removing and Installing the System Board 1. I/O connector cover 2. retention latch 3. system board 4. tabs on system chassis 5. slots in system board tray Installing The System Board 1.
5. Replace the hard drive(s)/SSDs. Ensure that you reinstall the hard drives/SSDs in their original locations. 6. Reinstall the cooling shroud. 7. Close the blade. 8. Remove the plastic I/O connector covers from the back of the blade. 9. Install the blade in the enclosure.
Figure 21. Replacing the NVRAM Backup Battery 1. positive side of battery 2. negative side of battery connector Storage Controller Card Your system includes a dedicated expansion-card slot on the blade system board for the storage controller card that provides the integrated storage subsystem for your system’s hard drives.
Figure 22. Removing and Installing the PCIe Extender/Storage Controller Card 1. PCIe extender/storage controller card 2. screws (2) 3. tab 4. connector Installing The PCIe Extender Card/Storage Controller Card 1.
58.
4 Troubleshooting Your System Safety First—For You and Your System CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Troubleshooting Hard Drives CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
1. Enter the System Setup and ensure that the Internal SD Card Port is enabled. 2. Note the Internal SD Card Redundancy option enabled in the Integrated Devices screen of the System Setup (Mirror or Disabled). 3. Remove the blade from the enclosure. 4.
Troubleshooting The NVRAM Backup Battery CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
5 Using System Diagnostics If you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance. The purpose of running system diagnostics is to test your system hardware without requiring additional equipment or risking data loss.
The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the system. The diagnostics starts executing the tests on all the detected devices. Running Embedded System Diagnostics From An External Media 1. Format the external resource media (USB flash drive or CDROM) to emulate a hard drive.
6 Jumpers And Connectors System Board Jumper Settings CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
System Board Connectors Figure 23. System Board Connectors Table 4. System Board Connectors Item Connector Description 1 BATTERY Connector for the 3.0 V coin cell battery 2 CPU2 Processor socket 2 3 B.
Item Connector Description 15 STORAGE PCIe extender card/storage controller card connector 16 USB2 USB connector 17 USB1 USB connector Disabling A Forgotten Password The blade's software security features include a system password and a setup password.
68.
7 Technical Specifications Processor Processor type One or two Intel Xeon processor E5-2600 product family Memory Architecture 1600 MT/s, 1333 MT/s, 1066 MT/s, or 800 MT/s DDR3 and LV-DDR3 DIMMs Memor.
Mezzanine Cards Mezzanine slots Two mezzanine PCIe x8 Gen 3 slots supporting dual-port Gb Ethernet, 10 Gb Ethernet, FC8 Fibre Channel, or Infiniband mezzanine cards Video Video type Matrox G200 integrated with iDRAC Video memory MB shared with iDRAC application memory Battery NVRAM backup battery CR 2032 3.
Environmental For temperatures between 40 °C and 45 °C, de-rate maximum allowable dry bulb temperature by 1 °C per 125 m above 950 m (1 °F per 228 ft). Expanded operating temperature restrictions • Do not perform a cold startup below 5 °C. • Maximum 95 W processor is supported.
72.
8 System Messages LCD Status Messages The LCD messages consist of brief text messages that refer to events recorded in the System Event Log (SEL). For information on the SEL and configuring system management settings, see the systems management software documentation.
Error Code Message Information Action 1. Review system power policy. 2. Check system logs for power related failures. 3. Review system configuration changes. 4. If the issue persists, see Getting Help . AMP0301 Message The system board < name > current is less than the lower warning threshold.
Error Code Message Information 4. If the issue persists, see Getting Help . AMP0306 Message Disk drive bay < name > current is less than the lower warning threshold. Details Disk drive bay < name > current is outside of the optimum range. Action 1.
Error Code Message Information Details Disk drive bay < name > current is outside of the optimum range. Action 1. Review system power policy. 2. Check system logs for power related failures. 3. Review system configuration changes. 4. If the issue persists, see Getting Help .
Error Code Message Information 4. If the issue persists, see Getting Help . AMP0316 Message System level current is outside of range. LCD Message System level current is outside of range. Details System level current is outside of the optimum range. Action 1.
Error Code Message Information 2. Check system logs for power related failures. 3. Review system configuration changes. 4. If the issue persists, see Getting Help . AMP0322 Message Chassis power level current is outside of range. Details Chassis power level current is outside of the optimum range.
Error Code Message Information Action Check the operating system, application, hardware, and system event log for exception events. ASR0100 Message The BIOS watchdog timer reset the system. Details The operating system or an application failed to communicate within the time-out period.
Error Code Message Information ASR0106 Message The watchdog timer expired. Details The operating system or an application failed to communicate within the time-out period. Action Check the operating system, application, hardware, and system event log for exception events.
Error Code Message Information BAT0012 Message The storage battery for disk drive bay < bay > has failed. LCD Message Battery for disk drive bay < bay > has failed. Check battery. Details Verify the cable connection between the storage battery and the controller.
Error Code Message Information CPU0001 Message CPU < number > has a thermal trip (over-temperature) event. LCD Message CPU < number > has a thermal trip. Check CPU heat sink. Details The processor temperature increased beyond the operational range.
Error Code Message Information CPU0008 Message CPU < number > is disabled. Details System is unable to boot or may run in a degraded state. Action If unexpected, check presence, and system setup (BIOS) configuration. CPU0010 Message CPU < number > is throttled.
Error Code Message Information Details Low voltages may be the result of a problem with the voltage regulator or a problem with the processor. The low voltage may cause the processor to fail to operate. Action 1. Turn system off and remove input power for one minute.
Error Code Message Information LCD Message CPU < number > < name > voltage is outside of range. Re-seat CPU. Details Voltages outside the allowable range may damage electrical components or may cause the system to shutdown. Action 1. Turn system off and remove input power for one minute.
Error Code Message Information 5. If the issue persists, see Getting Help . CPU0703 Message CPU bus initialization error detected. LCD Message CPU bus initialization error detected. Power cycle system. Details System event log and operating system logs may indicate that the exception is external to the processor.
Error Code Message Information 3. Ensure the processor is seated correctly. 4. If the issue persists, see Getting Help . CPU0803 Message The power input for CPU < number > voltage regulator module is lost. LCD Message Lost power input for CPU < number >voltage regulator module.
Error Code Message Information Details System performance may be degraded or the system may fail to operate. Action If removal was unintended, check presence and reinstall. HWC1001 Message The < name > is absent. LCD Message The < name > is absent.
Error Code Message Information Details The device may be necessary for proper operation. System functionality may be degraded. Action Check presence, then re-install or reconnect. HWC2008 Message A fabric mismatch detected between IOM and mezzanine card < number >.
Error Code Message Information Action Check presence of the hardware, reinstall or reconnect, then reattempt the update. If the issue persists, see Getting Help . HWC4013 Message Hardware unsuccessfully updated for embedded NIC. Action Check presence, reinstall or reconnect, then reattempt the update.
Error Code Message Information HWC5032 Message A fabric mismatch detected on IO module < number >. Details The fabric type for IOM's on the same chassis fabric must match. Action Check chassis fabric type in CMC GUI and compare to the type of both IOM's.
Error Code Message Information Action Review System Log or front panel for additional information. HWC7008 Message Server < number > health changed to a warning state from more severe state. Server < number > health changed to a critical state from a non-recoverable state.
Error Code Message Information Action Re-seat the memory modules. If the issue persists, see Getting Help . MEM0004 Message Memory device at location < location > is disabled. Details The memory may not be seated correctly, misconfigured, or has failed.
Error Code Message Information Details The memory may not be operational. This an early indicator of a possible future uncorrectable error. Action Re-seat the memory modules. If the issue persists, see Getting Help . MEM0702 Message Correctable memory error rate exceeded for < location >.
Error Code Message Information Action Check the memory configuration. Re-seat the memory modules. If the issue persists, see Getting Help . MEM1206 Message Memory mirror redundancy is degraded. Check memory device at location < location >. Details The memory may not be seated correctly, misconfigured, or has failed.
Error Code Message Information OSE0001 Message A runtime critical stop occurred. Details The system halted due to an exception while the operating system was running. This is a kernel panic or bug check event. Action Review operating system logs and system video for additional information.
Error Code Message Information Action Review system boot configuration and boot media. See system video for additional information. PCI1302 Message A bus time-out was detected on a component at bus < bus >device< device >function < func >.
Error Code Message Information Details System performance may be degraded, or system may fail to operate. Action Cycle input power, update component drivers, if device is removable, reinstall the device. PCI1318 Message A fatal error was detected on a component at bus < bus >device< device >function < func >.
Error Code Message Information Action Cycle input power, update component drivers, if device is removable, reinstall the device. PCI1350 Message A PCI system error was detected on a component at slot < number >. LCD Message PCI parity error on slot < number >.
Error Code Message Information LCD Message Fatal IO error on bus < bus > device < device > function < func >. Details System performance may be degraded, or system may fail to operate. Action Cycle input power, update component drivers, remove and reinstall the device.
Error Code Message Information PCI3010 Message A non-fatal IO error detected on a component at bus < bus >device< device >function < func >. Details System performance may be degraded. Action Cycle input power, update component drivers, remove and reinstall the device at the next service window.
Error Code Message Information Details The controller received a SMART error from the drive. The drive is operational but needs replacement. Action The drive will need replacement at the next service window. PDR1016 Message Drive < number > is removed from disk drive bay < bay >.
Error Code Message Information Action Remove input power. Reduce system memory to minimum configuration and apply input power. PST0132 Message CMOS failed. LCD Message CMOS failed. Power cycle system. Details System BIOS detected a failure with CMOS memory during system POST.
Error Code Message Information Details System BIOS detected a failure with the SIO. Action Remove and reapply input power. If the issue persists, see Getting Help . PST0139 Message Keyboard controller failed. LCD Message Keyboard controller failed. Power cycle system.
Error Code Message Information PST0193 Message BIOS POST memory test failed. LCD Message BIOS POST memory test failed. Check memory devices. Details System BIOS POST memory test failed. Action Compare system memory installation to supported system memory configurations.
Error Code Message Information PSU0002 Message A predictive failure detected on power supply < number >. LCD Message Predictive failure on PSU < number >. Check PSU. Details System performance and power redundancy may be degraded or lost. Action Remove and reinstall the power supply at the next service window.
Error Code Message Information PSU0008 Message Power supply < number > voltage rating does not match the system's requirements. Details The system does not support mixed voltage power supplies. Action Install a power supply with the correct voltage rating.
Error Code Message Information Details The current power operational mode is non-redundant because of a power supply exception, a power supply inventory change, or a system power inventory change. Action Check the event log for power supply failures. Review system configuration and power consumption.
Error Code Message Information LCD Message System power exceeds capacity. Performance degraded. Check PSU configuration. Details The system is currently operating in a performance degraded state to attempt protect from a power shutdown. Action Review system configuration, upgrade power supplies or reduce system power consumption.
Error Code Message Information RFM1016 Message Media not present for Removable Flash Media < name >. Details The SD card is not detected or not installed. Action If unintended, reinstall the flash media. RFM1021 Message Removable Flash Media is not IPMI-function ready.
Error Code Message Information Action Replace the failed SD card. RFM1202 Message Internal Dual SD Module redundancy is degraded. Details Either one of the SD card or both the SD cards are not functioning properly. Action Replace the failed SD card. RFM1203 Message Internal Dual SD Module is not redundant.
Error Code Message Information LCD Message Intrusion detected. Check chassis cover. Details The chassis is open. System performance may be degraded, and security may be compromised. Action Close the chassis. Check system logs. SEC0001 Message The drive bay is open.
Error Code Message Information Details The chassis is open. System performance may be degraded, and security may be compromised. Action Close the chassis. Check system logs. SEC0033 Message The chassis is open while the power is off. LCD Message Intrusion detected.
Error Code Message Information SEC0600 Message A secure mode violation detected. Details This may apply to a physical or remote access attempt. Action Check system logs for intrusion attempts, and ensure strong password policies. SEC0602 Message User password violation detected.
Error Code Message Information SEL0010 Message Log is almost full. Details When the event log is full, additional events are not written to the log. Older events may be overwritten and lost. Action Backup and clear log at the next maintained time. SEL0012 Message Could not create or initialize the system event log.
Error Code Message Information SEL1304 Message The PXE server not found. Details PXE is one way to boot a system from the network. Action Check the network and PXE server configuration. SEL1306 Message Invalid boot sector found. Details The disk in the drive is not formatted correctly or does not contain the necessary operating system files.
Error Code Message Information SEL1510 Message An authentication error detected for Chassis Group Member < number >. Details Group master CMC could not log into the group member CMC. Action Check the login credentials of CMC. SEL9900 Message An unsupported event occurred.
Error Code Message Information TMP0102 Message The system board < name > temperature is greater than the upper warning threshold LCD Message System board < name > temperature is outside of range. Details Ambient air temperature is too warm or one or more fans may have failed.
Error Code Message Information Action The system board < name > temperature is outside of the optimum range. Check Fans. TMP0110 Message The memory module < number > temperature is outside of range. LCD Message Memory module < number > temperature is outside of range.
Error Code Message Information TMP0119 Message The system inlet temperature is less than the lower critical threshold. LCD Message System inlet temperature is outside of range. Details Ambient air temperature is too cool. Action Check the system operating environment.
Error Code Message Information LCD Message Disk drive bay temperature is outside of range. Check Fans. Details Ambient air temperature is too warm or cool. Action Check the system operating environment and review event log for fan failures. TMP0130 Message The control panel temperature is less than the lower warning threshold.
Error Code Message Information 3. If the issue persists, see Getting Help . VLT0102 Message Processor module < name > voltage is greater than the upper warning threshold. LCD Message Processor module < name > voltage is outside of range. Details System hardware detected an over voltage or under voltage condition.
Error Code Message Information 2. Remove the processor module. Inspect processor socket for bent pins. 3. If the issue persists, see Getting Help . VLT0201 Message The system board < name > voltage is less than the lower warning threshold. LCD Message System board voltage is outside of range.
Error Code Message Information If multiple voltage exceptions occur consecutively the system may power down in fail- safe mode. Action 1. Review system logs for power supply exceptions. 2. Re-configure the system to minimum configuration, inspect and reinstall system cables.
Error Code Message Information 3. If the issue persists, see Getting Help . VLT0209 Message The memory module < number > < name > voltage is greater than the upper critical threshold. LCD Message Memory module < number > < name > voltage is outside of range.
Error Code Message Information If multiple voltage exceptions occur consecutively the system may power down in fail- safe mode. Action 1. Review system logs for power supply exceptions. 2. Re-configure the system to minimum configuration, inspect and reinstall system cables.
Error Code Message Information VLT0218 Message The < name > voltage is less than the lower warning threshold. LCD Message The < name > voltage is outside of range. Details System hardware detected an over voltage or under voltage condition.
Error Code Message Information 2. Re-configure the system to minimum configuration, inspect and reinstall system cables. 3. If the issue persists, see Getting Help . VLT0222 Message The < name > voltage is outside of range. LCD Message The < name > voltage is outside of range.
Error Code Message Information Details System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in fail- safe mode. Action 1. Review system logs for power supply exceptions.
Error Code Message Information Details System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in fail-safe mode. Action 1. Review system logs for power supply exceptions.
NOTE: Warning messages are generated by either the application or the operating system. For more information, see the documentation that accompanied the operating system or application. Diagnostic Messages The system diagnostic utilities may issue messages if you run diagnostic tests on your system.
132.
9 Getting Help Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Ein wichtiger Punkt beim Kauf des Geräts Dell M620 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dell M620 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dell M620 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dell M620 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dell M620 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dell M620 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dell M620 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dell M620. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dell M620 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
