Benutzeranleitung / Produktwartung 8500 des Produzenten Dell
Zur Seite of 45
Dell™Inspiron™8500/8600ServiceManual Before You Begin System Components Memory Module, Mini PCI Card, Modem, and Modules Color Insert Cover Hard Drive Bluetooth™Card Fan Docking D.
Back to Contents Page Before You Begin Dell™Inspiron™8500/8600ServiceManual Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Preparing to Work Inside the Computer 1.
Recommended Tools The procedures in this manual require the following tools: l #1 Phillips screwdriver l ¼ - inch flat - blade screwdriver l Small plastic scribe l Flash BIOS updat.
(1 each) (1 each) (1 each) Fan: (2 each) Keyboard: (2 each) Display Assembly: (2 each) Display Bezel: (shoulder scre.
(4 each) (2 each) (13 each) (1 each) System Board: (3 each) (2 each) (1 each) .
Back to Contents Page .
Back to Contents Page Flashing the BIOS Dell™Inspiron™8500/8600ServiceManual 1. Ensure that the AC adapter is plugged in and that the main battery is installed properly. 2. Insert the flash BIOS update program floppy disk or CD and turn on the computer.
Back to Contents Page Bluetooth™Card Dell™Inspiron™8500/8600ServiceManual If you ordered a Bluetooth card with your computer, the card is already installed. 1. Remove the hard drive . 2. Pull the Bluetooth card connector out of the system board connector.
Back to Contents Page Color Insert Cover Dell™Inspiron™8500/8600ServiceManual Removing the Color Insert Cover 1. Press down along the front of the display as shown. 2. Firmly grasp the lip of the cover to detach it from the computer, and pull the cover up.
Back to Contents Page Microprocessor Module Dell™Inspiron™8500/8600ServiceManual Removing the Microprocessor Module 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the keyboard .
6. Lift out the microprocessor module. Installing the Microprocessor Module 1. Align the pin - 1 corner of the microprocessor module with the pin - 1 corner of the ZIF socket, and insert the microprocessor module. When the microprocessor module is correctly seated, all four corners are aligned at the same height.
Back to Contents Page Display Assembly Dell™Inspiron™8500/8600ServiceManual Display Assembly Display Bezel Display Panel Display Assembly 1. Follow the instructions in " Preparing to Work Inside the Computer .
1 display 2 display cable connector 3 computer base 4 pull - tab 5 connector 6 EMI clip 1 M2.5 x 4.5 - mm shoulder screws (2) 5 display bezel 2 shoulder screw covers (2) 6 display panel 3 display bumpers (6) 7 top cover 4 M2.
Display Bezel 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the central control cover . 3. Remove the display assembly . 4. Use a plastic scribe to pry the eight display bumpers out of the screw holes located on the front of the bezel.
9. Use the pull - tab to disconnect the bottom flex - cable connector from the inverter connector. 10. Remove the yellow tape from above the bottom flex - cable connector.
Back to Contents Page Docking Doors Dell™Inspiron™8500/8600ServiceManual Removing the Docking Doors 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Gently bend the docking covers and lift them away from the computer base.
Back to Contents Page 1 docking doors with spring 2 longer post.
Back to Contents Page Fan Dell™Inspiron™8500/8600ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the two M2.5 x 12 screws from the fan cover. 3. Lift the fan out of the computer.
Back to Contents Page Hard Drive Dell™Inspiron™8500/8600ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Turn the computer over. Use a standard #1 Phillips screwdriver to remove the M3 x 3 - mm screw.
Back to Contents Page Keyboard Dell™Inspiron™8500/8600ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Turn the computer right - side up and open it. 3. Remove the center control cover: a.
4. Remove the keyboard: a. Remove the two M2.5 x 6 - mm screws across the top of the keyboard. b. Rotate the keyboard up and slide it forward. c. Hold the keyboard up and slightly forward to allow access to the keyboard connector.
Back to Contents Page Base Latch Dell™Inspiron™8500/8600ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the hard drive . 3. Remove the keyboard . 4. Remove the display assembly .
Back to Contents Page Palm Rest Dell™Inspiron™8500/8600ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the keyboard . 3. Remove the display assembly .
8. Disconnect the touch pad connector from the system board. 9. Use your fingers to separate the palm rest from the computer base.
Back to Contents Page Pin Assignments for I/O Connectors Dell™Inspiron™8500/8600ServiceManual USB Connector Video Connector Parallel Connector S- Video .
Parallel Connector S- Video TV - Out Connector Serial Connector Pin Signal Pin Signal 1 STROBE – 10 ACK – 2 PD0 11 BUSY 3 PD1 12 PE 4 PD.
Back to Contents Page Pin Signal Pin Signal 1 DCD 6 DSR 2 RXDA 7 RTS 3 TXDA 8 CTS 4 DTR 9 RI 5 GND .
Back to Contents Page Reserve Battery Dell™Inspiron™8500/8600ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the battery . 3. Depress the battery latch and rotate it out to remove the reserve battery cover.
.
Back to Contents Page Speakers Dell™Inspiron™8500/8600ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the keyboard . 3. Remove the display assembly . 4.
Back to Contents Page System Board Dell™Inspiron™8500/8600ServiceManual Removing the System Board The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the bottom of the computer.
11. Remove the M2.5 x 12 - mm screw labeled "circle B" from the computer base. 12. Remove the system board from the computer base.
Installing the System Board 1. Perform all the steps in " Removing the System Board " in reverse order. 2. Turn on the computer. 3. Insert the floppy disk or CD that accompanied the replacement system board into the appropriate drive.
Back to Contents Page System Components Dell™Inspiron™8500/8600ServiceManual Back to Contents Page NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Back to Contents Page Microprocessor Thermal - Cooling Assembly Dell™Inspiron™8500/8600ServiceManual Removing the Microprocessor Thermal - Cooling Assembly 1. Follow the instructions in " Preparing to Work Inside the Computer .
Installing the Microprocessor Thermal - Cooling Assembly 1. Place the left side of the microprocessor thermal - cooling assembly under the palm rest and rotate the assembly onto the system board. 2. Tighten the four captive screws, labeled "1" through "4," in consecutive order.
Back to Contents Page Dell™Inspiron™8500/8600ServiceManual Information in this document is subject to change without notice. © 2003DellInc.Allrightsreserved. Reproduction in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Memory Module, Mini PCI Card, Modem, and Modules Dell™Inspiron™8500/8600ServiceManual Memory Module Mini PCI Card Modem Modules Memory Module 1. Follow the instructions in " Preparing to Work Inside the Computer .
4. Ground yourself and install the new memory module: a. Align the notch in the module with the slot in the center of the connector. b. Slide the edge of the module firmly into the connector, and rotate the module down until you feel a click.
3. If a Mini PCI card is not already installed, go to step4 . If you are replacing a Mini PCI card, remove the existing card: a. Disconnect the Mini PCI card from any attached cables. b. Release the Mini PCI card by spreading the metal securing tabs until the card pops up slightly.
6. Replace the cover and tighten the screw. Modem 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Turn the computer over, and loosen the captive screw from the Mini PCI card/modem cover.
4. Connect the modem cable to the modem. 5. Align the modem with the screw hole, and press the modem into the connector directly over the connector on the system board. Modules Your computer ships with an optical drive installed in the module bay.
2. Pull the device by the latch release to remove the device from the module bay. If the Device Screw Is Installed 1. If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions.
4. Press the device latch release so that the latch release pops out. 5. Pull the device by the latch release to remove the device from the module bay. Back to Contents Page NOTICE: Insert devices into the module bay before you dock and turn on the computer.
Back to Contents Page Video Card Dell™Inspiron™8500/8600ServiceManual 1. Follow the instructions in " Preparing to Work Inside the Computer ." 2. Remove the keyboard . 3. Remove the display . 4. Remove the four M2.
Ein wichtiger Punkt beim Kauf des Geräts Dell 8500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dell 8500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dell 8500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dell 8500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dell 8500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dell 8500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dell 8500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dell 8500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dell 8500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
