Benutzeranleitung / Produktwartung 19 des Produzenten Dell
Zur Seite of 53
Dell Studio One 19/1909 Service Manual Notes, Cautions, and Warnings Information in this document is subject to change without notice. © 2009DellInc.Allrightsreserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Before You Begin Dell Studio One 19/1909 Service Manual Recommended Tools Turning Off Your Computer Safety Instructions This chapter provides procedures for removing and installing the components in your computer.
2. Turn off your computer (see Turning Off Your Computer ). 3. Disconnect all telephone or network cables from the computer. 4. Disconnect your computer and all attached devices from their electrical outlets. 5. Press and hold the power button while the system is unplugged to ground the system board.
Back to Contents Page Cards Dell Studio One 19/1909 Service Manual Removing the WLAN Card Replacing the WLAN Card Removing the RF Module Replacing the RF Module Removing the WLAN Card 1. Follow the instructions in Before You Begin .
6. Replace the shield (see Replacing the Shield ). 7. Replace the computer cover (see Replacing the Computer Cover ). Removing the RF Module 1. Follow the instructions in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
3. Flip the RF module and align the screw hole on the RF module with the screw hole on the chassis. 4. Replace the screw that secures the RF module. 5. Replace the optical drive (see Replacing the Optical Drive ). 6. Replace the right speaker (see Replacing the Right Speaker ).
Back to Contents Page Battery Dell Studio One 19/1909 Service Manual Removing the Battery Replacing the Battery Removing the Battery 1. Record all the screens in system setup (see System Setup ) so that you can restore the correct settings in step 7 .
Replacing the Battery 1. Follow the procedures in Before You Begin . 2. Insert the new battery into the socket with the side labeled "+" facing up and then snap the battery into place. 3. Reconnect the cables to the connectors HDD_POWER and SATA_1 (see System Board Components ).
Back to Contents Page Computer Cover Dell Studio One 19/1909 Service Manual Removing the Computer Cover Replacing the Computer Cover Removing the Computer Cover 1. Follow the procedures in Before You Begin . 2.
Back to Contents Page .
Back to Contents Page Support Assembly Dell Studio One 19/1909 Service Manual Removing the Support Assembly Replacing the Support Assembly Removing the Support Assembly 1. Follow the instructions in Before You Begin .
Replacing the Support Assembly 1. Follow the instructions in Before You Begin . 2. Reconnect the following cables to the LCD panel: l LVDS cable from LVDS connector l touch pad cable from the touch pad connector l touch panel cable from the touch panel module 3.
Back to Contents Page Drives Dell Studio One 19/1909 Service Manual Removing the Hard Drive Replacing the Hard Drive Removing the Optical Drive Replacing the Optical Drive Removing the Hard Drive 1. Follow the procedures in Before You Begin .
Replacing the Hard Drive 1. Follow the procedures in Before You Begin . 2. Prepare the new hard drive for installation and check the documentation that accompanied the drive to verify that the drive is configured for your computer. 3. Align the screws holes on the hard drive with the screw holes on the hard drive carrier.
10. Remove the four screws securing the optical drive to the optical drive carrier. 11. Slide the optical drive out of the optical drive carrier.
9. Replace the back I/O panel (see Replacing the Back I/O Panel ). 10. Replace the stand (see Replacing the Stand ). 11. Replace the shield (see Replacing the Shield ).
Back to Contents Page Processor Fan and Heat Sink Dell Studio One 19/1909 Service Manual Removing the Heat Sink Replacing the Heat Sink Removing the Processor Fan Replacing the Processor Fan Removing the Heat Sink 1.
1. Follow the procedures in Before You Begin . 2. Clean the thermal grease from the bottom of the heat sink and reapply it. 3. Align the screws on the processor heat sink with the screw holes on the chassis.
6. Lift the processor fan away from the computer and place it in a secure location. Replacing the Processor Fan 1. Follow the procedures in Before You Begin . 2. Connect the processor fan cable to the connector (CPU_FAN1) on the system board.
Back to Contents Page Inverter Dell Studio One 19/1909 Service Manual Removing the Inverter Replacing the Inverter Removing the Inverter 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
Replacing the Inverter 1. Follow the procedures in Before You Begin . 2. To replace the inverter, connect the two cables from the LCD panel to the inverter. 3. Connect the inverter cable to the system board connector (INVERTER). 4.
Back to Contents Page Back I/O Panel Dell Studio One 19/1909 Service Manual Removing the Back I/O Panel Replacing the Back I/O Panel Removing the Back I/O Panel 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
6. Replace the computer cover (see Replacing the Computer Cover ). 7. Connect your computer and all attached devices to electrical outlets, and turn them on.
Back to Contents Page Memory Module(s) Dell Studio One 19/1909 Service Manual Removing Memory Module(s) Replacing Memory Module(s) Removing Memory Module(s) 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
10. Check the amount of memory (RAM) listed. Back to Contents Page .
Back to Contents Page Microphone Dell Studio One 19/1909 Service Manual Removing the Microphone Replacing the Microphone Removing the Microphone 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
Back to Contents Page Processor Dell Studio One 19/1909 Service Manual Removing the Processor Replacing the Processor Removing the Processor 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
Replacing the Processor 1. Follow the procedures in Before You Begin . 2. Lift the release lever to the release position so that the socket is ready for the new processor. 3. Unpack the new processor. 4. If the release lever on the socket is not fully extended, move it to that position.
11. Apply the new thermal grease to the top of the processor. 12. Replace the processor heat sink (see Replacing the Heat Sink ). 13. Replace the back I/O panel (see Replacing the Back I/O Panel ). 14. Replace the stand (see Replacing the Stand ).
Back to Contents Page Power Supply Unit Dell Studio One 19/1909 Service Manual Removing the Power Supply Unit Replacing the Power Supply Unit Removing the Power Supply Unit 1. Follow the procedures in Before You Begin .
Replacing the Power Supply Unit 1. Follow the procedures in Before You Begin . 2. Replace the four screws that secure the power supply unit to the chassis. 3. Connect the power supply unit cable to the connector (ATX_POWER1) on the system board.
Back to Contents Page Shield Dell Studio One 19/1909 Service Manual Removing the Shield Replacing the Shield Removing the Shield 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
Back to Contents Page Side I/O Panel Dell Studio One 19/1909 Service Manual Removing the Side I/O Panel Replacing the Side I/O Panel Removing the Side I/O Panel 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
Replacing the Side I/O Panel 1. Follow the procedures in Before You Begin . 2. To replace the side I/O panel, route the cables back into position and connect them to the connectors (F_AUDIO and SIDE_BOARD_1) on the system board. 3. Slide the side I/O panel towards the clamps until it is firmly seated.
Back to Contents Page Speakers Dell Studio One 19/1909 Service Manual Removing the Right Speaker Replacing the Right Speaker Removing the Left Speaker Replacing the Left Speaker Removing the Right Speaker 1.
2. To replace the speaker, route the speaker cables back into position. 3. Connect the right speaker cable to the connector (SPEAKER_2) on the system board. 4. Place the speaker in position and replace the four screws that secure the speaker to the chassis.
3. Reconnect the left speaker cable to the connector (SPEAKER_1) on the system board. 4. Replace the four screws that secure the speaker to the chassis. 5. Replace the shield (see Replacing the Shield ). 6. Replace the computer cover (see Replacing the Computer Cover ).
Back to Contents Page Stand Dell Studio One 19/1909 Service Manual Removing the Stand Replacing the Stand Removing the Stand 1. Follow the procedures in Before You Begin . 2. Remove the computer cover (see Removing the Computer Cover ).
.
Back to Contents Page System Board Dell Studio One 19/1909 Service Manual Removing the System Board Replacing the System Board The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the computer.
11. Lift the system board out of the chassis. Replacing the System Board 1. Follow the instructions in Before You Begin . 2. To replace the system board place the system board back in the chassis. 3. Replace the five M2.5 x 5 - mm screws that secure the system board to the chassis.
Back to Contents Page System Fan and Heat Sink Assembly Dell Studio One 19/1909 Service Manual Removing the System Fan and Heat Sink Assembly Replacing the System Fan and Heat Sink Assembly Removing the System Fan and Heat Sink Assembly 1.
10. Lift the assembly away from the system board and place it in a secure location. Replacing the System Fan and Heat Sink Assembly 1. Follow the procedures in Before You Begin . 2. To replace the system fan and heat sink assembly, connect the system fan cable to the connector (SYS_FAN1) on the system board.
Back to Contents Page System Setup Dell Studio One 19/1909 Service Manual Overview Clearing Forgotten Passwords Clearing CMOS Settings Flashing the BIOS Overview Us.
Boot Sequence This feature allows you to change the boot sequence for devices. Boot Options Processor L2 Cache Displays the processor L2 cache size. Memory Installed Indicates the amount of installed memory in MB. Memory Available Indicates the amount of memory available in MB.
l Hard Drive — The computer attempts to boot from the primary hard drive. If no operating system is on the drive, the computer generates an error message. l CD/DVD Drive — The computer attempts to boot from the CD/DVD drive. If no CD/DVD is in the drive, or if the CD/DVD has no operating system, the computer generates an error message.
6. Remove the 2 - pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2. 7. Wait for approximately five seconds to clear the password setting. 8. Remove the 2 - pin jumper plug from pins 1 and 2 and replace it on pins 2 and 3. 9.
7. Remove the 2 - pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2. 8. Wait for approximately five seconds to clear the CMOS setting. 9. Remove the 2 - pin jumper plug from pins 1 and 2 and replace it on pins 2 and 3. 10. Replace the back I/O panel (see Replacing the Back I/O Panel ).
8. Double - click the file icon on the desktop and follow the instructions on the screen. Flashing the BIOS From a CD 1. Turn on the computer 2. Insert the BIOS upgrade CD, and restart the computer. Follow the instructions that appear on the screen.
Back to Contents Page Technical Overview Dell Studio One 19/1909 Service Manual Inside View of Your Studio One System Board Components Inside View of Your Studio One System Board Components WARNING: Before working inside your computer, read the safety information that shipped with your computer.
Back to Contents Page 9 RF connector (RF_1) 10 CMOS jumper (CLR_CMOS) 11 processor 12 processor fan connector (CPU_FAN1) 13 right speaker connector (SPEAKER_2) 14 memory module connector (SODIMM1).
Back to Contents Page Dell Studio One 19/1909 Service Manual Information in this document is subject to change without notice. © 2009DellInc.Allrightsreserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
Back to Contents Page Webcam Dell Studio One 19/1909 Service Manual Removing the Webcam Replacing the Webcam Removing the Webcam 1. Follow the instructions in Before You Begin . 2. Remove the system board (see Removing the System Board ).
Ein wichtiger Punkt beim Kauf des Geräts Dell 19 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dell 19 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dell 19 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dell 19 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dell 19 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dell 19 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dell 19 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dell 19. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dell 19 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
