Benutzeranleitung / Produktwartung 10-ST2E des Produzenten Dell
Zur Seite of 37
Dell Latitude 10 – ST2e Owner's Manual Regulatory Model: T05G Regulatory Type: T05G001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents Notes, Cautions, and Warnings ...................................................................................................2 1 Working on Your Computer ....................................................................................
Running the ePSA Diagnostic Utility .......................................................................................................................27 Beep Codes ..................................................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display.
NOTE: It is recommended that you immediately backup the operating system image using the USB device through Dell Backup and Recovery (DBAR) application.
8.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may req.
5. volume button 6. speaker 7. battery 8. docking board 9. coin-cell battery 10. speaker Removing the Base Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Pry and lift the base cover from the computer by following the arrow sequence in the diagram.
Installing the Battery 1. Tighten the screws to secure the battery to the computer. 2. Install the base cover. 3. Follow the procedures in After Working Inside Your Computer. Removing the Front Camera 1. Follow the procedures in Before Working Inside Your Computer .
Installing the Front Camera 1. Place the camera module in its slot on the computer. 2. Tighten the screw to secure the camera module to the computer. 3. Connect the camera cable to the connector. 4. Install the: a) battery b) base cover 5. Follow the procedures in After Working Inside Your Computer .
5. Un-route the speaker cable on the side of the computer and lift it up to release the speaker from the computer. 6. Un-route the speaker cable on the side of the computer and lift it up to release the speaker from the computer.
Installing the Speakers 1. Place the right and the left speakers in their slot. 2. Route the speaker cables on the chassis. 3. Tighten the screws to secure the speakers to the chassis. 4. Place the coin-cell battery in its slot and route the cables. 5.
4. Remove the screws that secure the docking board to the computer. 5. Remove the docking board from the computer and disconnect the home-button board cable. Installing the Docking Board 1. Connect the home-button board cable to the docking board and place the docking board in its slot in the computer.
Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) base cover b) battery c) speaker d) front camera e) docking board 3. Disconnect the LVDS and docking board cables. 4. Remove the screws that secure the system board to the computer.
4. Install the: a) docking board b) front camera c) speaker d) battery e) base cover 5. Follow the procedures in After Working Inside Your Computer . Removing the Rear Camera 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) base cover b) battery c) speaker d) front camera e) system board 3.
Removing the Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the: a) base cover b) battery c) speaker d) front camera e) system board 3. Disconnect the coin-cell battery cable and remove it from the computer.
b) battery 3. Disconnect the volume-board cable from the connector. Lift up and remove the volume-board cable from the system board. 4. Pry the sides of the volume-button board with a flat-head screw driver to loosen it from it's slot on the computer.
20.
3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Keystroke Action connected to an optional external USB keyboard) On Screen Mouse Pointer Use this to navigate the System Setup by using your finger or an interactive pen. Apply Icon Save current configuration. Defaults Icon Load setup defaults. Exit Icon Exits System Setup.
Table 3. Boot Sequence Option Function File Browser Add Boot Option Displays the order that the BIOS searches devices when trying to find an operating system to boot. A new device can be added here. File Browser Del Boot Option A displayed boot device can be removed from the boot order.
Option Description Click OK after entering the password details. System Password Allows you to set, change, or delete the computer password (previously called the primary password).
Option Description Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin password is set. • Enable Admin Setup Lockout (Default) Table 8. Secure Boot Option Function Secure Boot Enables or Disables the secure boot feature.
Option Description • Disabled - Does not allow the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN. (Default ) • LAN Only - Allows the system to be powered on by special LAN signals. Table 11.
4 Troubleshooting Your Computer You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Enhanced Pre-boot System Assessment (ePSA) The ePSA is a diagnostic utility available on your computer.
2. The computer will start up and begin running the ePSA utility automatically. 3. During the testing process, you will be prompted to answer a YES or NO question.
4. Press the Security Button (<Ctrl> + <Alt> + <Del>) to click OK once the tests are completed. 5. The volume up and down buttons can also be used as the <Tab> key when switching between options. Beep Codes The computer may emit a series of beeps during start-up if the display cannot show errors or problems.
Code Cause and Troubleshooting Steps System board failure, covers BIOS corruption or ROM error 2 No RAM detected No memory detected 3 Chipset Error (North and South Bridge Chipset, DMA/IMR/ Timer Erro.
Code Cause and Troubleshooting Steps 6 Video BIOS test failure Video card failure 7 CPU - cache test failure Processor failure 8 Display Display failure 31.
32.
5 Specifications Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information regarding the configuration of your computer, click Start → Help and Support and select the option to view information about your computer.
Video Video type integrated Data bus internal Video controller Intel Graphics Media Accelerator Communications Network adapter USB 2.0 based Gigabit LAN via dock Ports and Connectors Audio one microphone-in and stereo headphones/speakers combo connector Video one mini HDMI connector USB one USB 2.
Battery Width 86.50 mm (3.40 inches) Weight 220.00 g (0.49 lb) Voltage 7.4 VDC Temperature range Operating 0 °C to 50 °C (32° F to 158 °F) Non-Operating -20 °C to 65 °C ( –4 °F to 149 °F) Coin-cell battery 3 V CR2025 lithium ion AC Adapter Type Input voltage 100 VAC to 240 VAC Input current (maximum) 0.
Environmental Operating –16 m to 3048 m (–50 to 10,000 ft) Non-operating –15.2 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G1 as defined by ISA-71.
6 Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Ein wichtiger Punkt beim Kauf des Geräts Dell 10-ST2E (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dell 10-ST2E noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dell 10-ST2E - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dell 10-ST2E reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dell 10-ST2E erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dell 10-ST2E besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dell 10-ST2E verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dell 10-ST2E. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dell 10-ST2E gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
