Benutzeranleitung / Produktwartung FPC 1702-P24 des Produzenten CyberResearch
Zur Seite of 81
® FPC 1702 Series NEMA 4 Sealed 17" Panel PCs FPC 1702-C20: 2.0GHz Celeron CPU FPC 1702-P24: 2.4GHz Pentium CPU FPC 1702-P30: 3.0GHz Celeron CPU All models are available wi th optional touchscreens Panel PCs USER’S MANUAL VER. 1.1 • JAN 2004 No part of this manual may be reproduced without permission CyberResearch ® , Inc.
.
.
.
CyberResearch ® P anel PCs FPC 1702 Series ©Copyright 2004 All Rights Reserved. January, 3 2004 The information in this document is su bject to change without prior notice in order to improve reliability, desi gn, and function and does not represent a commitment on the part of CyberResearch, Inc.
FPC 1702 Series CyberResearch ® Panel PCs Intentionally Blank iv ©Copyright 2004 Cy berResearc h, Inc..
CyberResearch ® P anel PCs FPC 1702 Contents General Information .........................................................................................................1 Introduction .................................................................
FPC 1702 CyberResearch ® Panel PCs Power Management Setup .................................................................................50 PnP/PCI Configuration ......................................................................................
CyberResearch ® P anel PCs FPC 1702 CyberResearch, Inc . vii 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.cyberresearch.
Chapter 1 General Information.
Introduction FPC 1702 is one of the fines t panel PCs in the CyberResearch product line. It features a PGA478 socket that can accommodate Pentium® 4 and Celeron® Processor s , supporting FSB up to 400/533MHz.
performance application. Most of all Pentium® 4 Level processors are suitable for FPC 1702 . FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
CyberResearch ® P anel PCs FPC 1702 CyberResearch, I nc 4 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.cyberresearch.
Safety 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning.
c . The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the users manual. e . The equipment has been dropped and damaged.
F C C Safety This device complies with Part 15 FCC Rules. Operation is subject t o the following two conditions: (1) t his device may not cause harmful interference, a n d (2) t his device must accept any interference received including interference that may cause undesired operation.
Features 1 7 ” TFT SXGA (1 2 8 0 x 1024) LCD All-in-one SBC s upport s Socket 478 based Intel® Pentium® 4 Processor Support s Intel® Hyper-Threading Technology Anti-vibration disk.
Specifications System C onstruction Heavy - duty steel chassis & IP -65 certified aluminum front panel (or optional stainless stee l front panel) C P U Socket 478 based Pentium® 4(.
R S -232/422/485 (COM 4 is reserved for touch screen) 1 parallel port (supports ECP/EPP) 1 PS/2 mouse and keyboard port 1 VGA port Mic in, Line in, Line out, S/ P DIF 5.1 channels audio port GPIO: 16 in or 16 out Storage Disk Drive Anti-v ibration 2.
75/100mm holes Expansion slots 2 PCI slots 1 Mini PCI socket 6in1 card reader. Because of a driver bug, after successfully installing card reader drivers, two vanity disk drives appear: XD and Flash.
Power Supply AC input 250W (standard offer): Output rating: 250 W Input voltage: 100VAC~240VAC@47~63Hz Output voltage: + 3.3V@16 A , + 5 V@2 5A, +12V@13A, +5VSB@2A, - 5V@0.
LCD Specifications Display type 17” color TFT LCD Max. Resolution 1280 x 1024 Max. Colors 256K Dot size (mm) 0 .2 64 x 0.2 6 4 Luminance (cd/m 2 ) 260 (TYP) Viewing angle 160 ° (H) 160 ° (V) Back .
Vibration 1G / 5~500Hz (Random / operation) Shock 15G peak acceleration (1 1 msec. duration) / operation EMC CE/FCC Class B CyberResearch ® P anel PCs FPC 1702 CyberResearch, Inc . 14 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.
25.00 Dimension 8.00 399.00 323.70 130.00 130.00 25.00 120.60 7.00 246.00 55.00 364.00 17.50 446.00 402.00 Unit : mm FPC 1702 Cutout Size : 449 X 367 483.00 137.00 465.00 36.00 150.00 150.00 FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
Chapter 2 Hardware Installation Notice: The Quick Installation Guide is derived f r o m Chapter 2 of user manual. For other chapters and further installation instruction s , please refer to the user manual CD -R O M that ca me with the p roduct.
Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board.
Location of Connectors and Jumpers Component Side CyberResearch ® P anel PCs FPC 1702 CyberResearch, Inc . 18 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.
List of Jumpers There are a number of jumpers in the board that allow you to configure your system to suit your application. The table below shows the function of each jumper in the board : Jumpers La.
List of Connectors Th e re are a number of connectors in the board that allow you to configure your system to suit your application. The table below shows the function of each connector in the board :.
Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
Clear CMOS ( JP1) Warning: To avoid damaging the computer, always turn off the power supply before setting “ Clear CMOS. ” Before turning on the power supply , set the jumper back to “ Normal.
COM2 RS- 232/422/485 Select ( JP4&JP5) JP4 JP 5 Function 1-2, 4 -5 , 7 -8, 10-1 1 1-2 RS-232 (Default) 2- 3 , 5 - 6 , 8 - 9, 1 1- 12 3- 4 R S- 422 2- 3 , 5 - 6 , 8 - 9, 1 1- 12 5- 6 R S- 485 ATX P.
IDE Connector (CN1) Pi n Signal Pi n Signal 1 IDE RESET 2 GND 3 DATA7 4 DATA8 5 DATA6 6 DATA9 7 DATA5 8 DATA10 9 DATA4 1 0 DATA11 1 1 DATA3 1 2 DATA12 1 3 DATA2 1 4 D ATA13 1 5 DATA1 1 6 DATA14 1 7 DATA0 1 8 DATA15 19 GN D 20 N . C 21 RE Q 22 GN D 2 3 IO WRITE 2 4 GND 2 5 IO READ 2 6 G N D 2 7 IO READY 2 8 GND 2 9 DACK 3 0 GN D 3 1 IRQ14 3 2 N .
Fan Con nector (CN8 &CN24) Pi n Signal 1 GND 2 +5V 3 FAN SPEED SENSE 10/100Base- Tx Ethernet C o n nector (CN11) Pi n Signal Pi n Signal 1 TX+ 9 N . C 2 TX - 1 0 N.C 3 RX+ 1 1 G N D 4 N.C 1 2 G N D 5 N.C 1 3 N.C 6 R X - 1 4 N.C 7 N.C 1 5 N.C 8 N.C 1 6 N.
Floppy Connector (CN13) P i n S ignal Pi n Signal 1 G ND 2 REDWC 3 GND 4 N . C 5 GND 6 DS1 7 GND 8 INDEX 9 GND 1 0 MOTOR A 1 1 GN D 1 2 DRIVE SELECT B 1 3 GND 1 4 DRIVE SELECT A 1 5 G N D 1 6 MOTOR B .
5 PTD1 6 INIT 7 PTD2 8 SLIN 9 PTD3 10 GND 11 PTD4 12 GND 13 PTD5 14 GND 15 PTD6 16 GND 17 PTD7 18 GND 19 A C K 20 GN D 21 BUSY 2 2 GND 23 PE 24 GN D 25 SELECT 26 N . C COM1~3 RS- 232/422/485 Serial Port Connector (CN16) Only COM1 support “ Wake on Ring” function.
2 3 RXD3 2 4 R TS3 2 5 TXD3 2 6 CTS3 27 DTR3 28 R I3 29 GN D 30 N . C 31 DCD4 32 DSR4 3 3 RXD4 3 4 RTS4 3 5 TXD4 3 6 CTS4 37 DTR4 38 R I4 39 GN D 40 N . C PS2 Keyboard/Mouse Connector (CN17) Pi n Signal 1 KB_DATA 2 KB_CLK 3 GND 4 +5V 5 MS_DATA 6 MS_CLK CyberResearch ® P anel PCs FPC 1702 CyberResearch, Inc .
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Digital I/O Port Pi n Signal I/O Address Setting Digital -IN / OUT 841H Digital -IN / OUT 841H Digital -IN / OUT 841H Digital -IN / OU.
The pin definitions and registers mapping are illustrated below: Address: 841H 4 in / 4 out Pin1 Pin2 Pin3 Pin4 Pin7 Pin8 Pin9 Pin10 GPI 27 GPI 26 GPI 25 GPI 24 GPO 23 GPO 22 GPO 21 GPO 20 MSB LSB 8 i.
8 out Pin13 Pin14 Pin15 Pin16 Pin1 9 Pin20 Pin21 Pin22 GPI 27 GPI 26 GPI 25 GPI 24 GPI 23 GPI 22 GPI 21 GPI 20 MSB LSB VGA Display Connector (C N 2 2) Pi n Signal Pi n Signal 1 Red 9 GN D 2 VCC 1 0 HSYNC 3 Green 11 GND 4 G ND 1 2 VSYNC 5 Blue 13 GND 6 N.
6 +5V 16 GND 7 GND 17 GND 8 POWER OK 1 8 - 5 V 9 +5VSB 1 9 + 5 V 10 +12V 20 +5V ATX Power 12V Connector (C N 28) Pi n Signal Pi n Signal 1 GND 2 GND 3 +12V 4 +12V CyberResearch ® P anel PCs FPC 1702 CyberResearch, In c 32 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.
FDD & CD - ROM Installation We will guide through installing the FDD and CD -ROM together. Please see the detail s below: Step 1: Plug in FDD cable Step 2: Fasten the FDD and CD - ROM together with two brac kets on the both sides symmetrically. FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
Step 3: Fasten the transferring bar with a pair of screws on the back of the CD - ROM. Step 4: Plug in CD - ROM Cable CyberResearch ® P anel PCs FPC 1702 CyberResearch, Inc 34 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.
HDD Installation In the following, we will guide you through installing the HDD. Make sure all parts are provided before you start the installation. Step 1: Lock with the screws as the illustration shown. Step 2: Cover the screws with four pieces of anti- vibration rubber FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
Step 3: Orient the two installation brackets as shown below. . Step 4: Install the HDD in the bracket as shown below. CyberResearch ® P anel PCs FPC 1702 CyberResearch, Inc 36 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.
Step 5: Install the other half of the bracket, then tighten the screws. Step 6: Install the HDD module into the FPC 1702 chassis and plug in the cable . Fix the HDD module with the screws Plug the cable in FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
Easy Stand Installation T wo L - shaped easy stands come with the product. Refer to the following illustration to install it. 1. Fix the L- shaped easy stands with the screws on both sides of the m onitor.
Panel Mount Kit Installation Some of the hardware that comes withe the product is for panel mounting. See the steps below along with the illustration. Refer to next page if installation waterproof seal. Step 1: Insert the screw into the panel-mounting clip .
Waterproof Seal Installation The following illustration shows you how to install the waterproof seal behind the FPC 1702 . 1. Plac e the seal behind the monitor set as shown below .
Chapter 3 BIOS Installation.
System test and initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non- fatal.
information has been erased. The FPC 1702 CMOS memory has an integral lithium battery backup for data retention. However, you will need to rep lace the complete unit when it finally runs down. Award BIOS Setup Awards BIOS ROM has a built- in Setup program that allows users to modify the basic system configuration.
Standard CMOS Features Use this menu for basic system configuration. (Date, time, IDE, etc.) Advanced BIOS Features Use this menu to set the advanced features available on your system. Advanced Chipset Features Use this menu to change the values in the chipset registe rs and optimize your system performance.
Set Supervisor/User Password Use this menu to set Supervisor/User Passwords. Save and Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup. FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
Standard CMOS Features When you choose the Standard CMOS Features option from the INITIAL SETUP SCREEN menu, the screen shown below is displayed. This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display.
Advanced BIOS F eatures By choosing the Advanced BIOS Features option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values . FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
Advanced Chipset Features By choosing the Advanced Chipset Features option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values .
Integrated Peripherals By choosing the I ntegrated P eripherals from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values . FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
Power management Setup By choosing the P ower Management Setup from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values . CyberResearch ® P anel PCs FPC 1702 CyberResearch, Inc 50 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.
PnP/ PCI configuration By choosing the PnP/PCI configurations from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values. FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
PC Health Status By choosing the P C Health Status from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values. CyberResearch ® P anel PCs FPC 1702 CyberResearch, Inc 52 25 Business Park Drive P: (203) 483-8815; F: (203) 483-9024 Branford, CT USA www.
Frequency/Voltage control By choosing the Frequency/V oltage Control from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values. FPC 1702 CyberResearch ® Panel PCs ©Copyright 2004 Cy berResearc h, Inc.
Load FPC 1702 Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar to: Load Default s (Y/N)? Pressing "Y" loads the BIOS default values for the most stable, minimal performance system operations.
Set Supervisor/User Password You can set either SUPERVISOR or USER PASSWORD, or both of them. The difference between the two is that the supervisor password allows unrestricted access to enter and change the options of the setup menus, while the user password only allows entry to the program, but not modify options.
Save & E xit Setup If you select this option and press <Enter>, the values entered in the setup utilities will be rec orded in the chipset’ s CMOS memory. The microprocessor will check this every time you turn o n your system and compare this to what it finds as it checks the system.
Exit without saving Selecting this o ption and pressing <Enter> allows you t o exit the Setup program without recording any new value or changing old one.
Limitations 1. Due to Intel chipset limitation, when CMOS was set up to “ LCD + CRT” , the LCD display will not support full- screen appearanc e . 2.
Chapter 4 Driver Installation.
I f you are unsure about which drivers to install, click on X: > Driver > System > FPC 1702. All drivers for the FPC 1702 are listed here. Each folder is labeled by step to indicate installation order.
system will ask you to reboot the computer. During the installation process, it appears as a pop-up window: 3 . Press ok . Another window appears: 4 . C hang e the path to the installation folder and search for the two files named as ikch8xx.cat and isb8xx.
Windows 98 CD ROM and key in its path. Then click on the OK button to key in path. 3. Click on the Finish button to finish installation process. And allow the system to reboot. 4. The LCD signal may be turned of f automatically after the VGA driver is installed, please press "Ctrl+Alt+F3" to enable LCD signal again.
Card Reader Driver Installation 1. Enter X: > Driver > System > FPC 1x02 → Step 6 Card Readers Driver folder. 2. Double click on the Setup exe. file. 3. Language setting: Choose the highlighted item below to operate your system in English. 4.
.
.
.
CyberResearch ® P anel PCs FPC 1702 Series Product Service Diagnosis and Debug CyberResearch, Inc. maintains technica l support lines staffed by experienced Applications Engineers and Technicians. There is no charge to call and we will return your call promptly if it is received while our li nes are busy.
FPC 1702 Series CyberResearch ® Panel PCs Intentionally Blank 66 ©Copyright 2004 CyberR esearch, In c..
CyberResearch ® P anel PCs FPC 1702 Series Warranty Notice CyberResearch, Inc. warrants t hat this equipment as furnished will be free f rom defects in material and workman ship for a period of one year from the confirmed date of purchase b y the original buyer and that upon written notice of any such defect, CyberResearch, Inc.
FPC 1702 Series CyberResearch ® Panel PCs Intentionally Blank 68 ©Copyright 2004 CyberR esearch, In c..
.
CyberResearch, Inc. 25 Business Park Drive Branford, CT 06405 USA P: (203) 483-8815; F: (203) 483-9024 www.cyberresearch.com.
Ein wichtiger Punkt beim Kauf des Geräts CyberResearch FPC 1702-P24 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie CyberResearch FPC 1702-P24 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für CyberResearch FPC 1702-P24 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von CyberResearch FPC 1702-P24 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über CyberResearch FPC 1702-P24 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon CyberResearch FPC 1702-P24 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von CyberResearch FPC 1702-P24 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit CyberResearch FPC 1702-P24. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei CyberResearch FPC 1702-P24 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
