Benutzeranleitung / Produktwartung Multimedia Presentation System 250 MPS-250 des Produzenten Crestron
Zur Seite of 94
Crestron MPS-250 Multimedia Presentation System 250 Operations Guide.
This document was prepared an d written by the Tech nical Documentation dep artment at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Important Safety Instructions • Read these instructions. • Keep these instr uctions.
Crestron MPS-250 Multimedia Presentation System 250 Operations Guide – DOC. 6647A Contents • i Contents Multimedia Presentation System 250: MPS-250 1 Introduction ....................................................................................
.
Crestron MPS-250 Multimedia Presentation System 250 Multimedia Presentation System 250: MPS-250 Multimedia Presentation System 250: MPS-250 Introduction Introduction The MPS-250 is a complete presentation control and sign al routing solution for boardrooms and classrooms.
Multimedia Presentation System 250 Crestron MPS-250 System Switcher Right out of the box , the MPS-2 50 provides high-perf ormance s witching of two video and t hree RGB c omputer sources t o a single pr ojector or plasm a display.
Crestron MPS-250 Multimedia Presentation System 250 Professional Audio Features Five stereo aud io inputs o n the rear panel accept balance d or unbalance d line-level signals from computers and othe r program audio sources. Addi tional audio s ources can be brought in th rough the QM input.
Multimedia Presentation System 250 Crestron MPS-250 custom touchpanel based system with multiple controlled sources and display devices, can be programmed easily using Crestron SystemBuilder™ software.
Crestron MPS-250 Multimedia Presentation System 250 Internal Block Diagram The following diagrams represent the video and aud io switching abilities of the MPS-250.
Multimedia Presentation System 250 Crestron MPS-250 Audio Block Diagram of the MPS-250 AUDIO INPUTS QM OUT 5 (Touchpanel) AUDIO OUTPUTS 6 QM Audio Combiner QM IN A/D A/D Local Mic Local Mic 1 2 Vol/EQ.
Crestron MPS-250 Multimedia Presentation System 250 MPS-250 Specifications (Continued) SPECIFICATION DETAILS Video/RGB Switcher Signal Types Video/HDTV Formats RGB Formats Maximum Resolution Blanking .
Multimedia Presentation System 250 Crestron MPS-250 MPS-250 Specifications (Continued) SPECIFICATION DETAILS Audio (continued) Limiter Curve Limiter Threshold Level Limiter Attack Time Limiter Release.
Crestron MPS-250 Multimedia Presentation System 250 MPS-250 Specifications (Continued) SPECIFICATION DETAILS LCD Display Green LCD alphanumeric, adj ustabl e backlight.
Multimedia Presentation System 250 Crestron MPS-250 MPS-250 Specifications (Continued) SPECIFICATION DETAILS Available Accessories: APAD C2N-DB12 C2N-FTB C2N-MNETGW CLS-C6(M) CLW-DIM1RF and CLW-SW1RF .
Crestron MPS-250 Multimedia Presentation System 250 MPS-250 Overall Dimensions 12.5 8 in (31.95 cm) 3.47 in (8.81 cm) 17.0 3 in (43.24 cm) 11.85 in (30.
Multimedia Presentation System 250 Crestron MPS-250 MPS-250 Buttons and Ports 1 2 3 4 5 6 8 9 10 11 12 14 16 17 19 20 29 18 21 23 24 22 27 25 28 30 31 33 15 26 7 13 32 12 • Multimedia Presentation System 250: MPS-250 Operations Guide – DOC.
Crestron MPS-250 Multimedia Presentation System 250 Connectors, Controls & Indicators # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 1 NET LED (1) yellow LED, indicates Cresnet bus activit y. 2 MSG LED (1) yellow LED, illuminates when a message is present in the message log.
Multimedia Presentation System 250 Crestron MPS-250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 8 MC/LN 1 – 2 (2) 5-pin 3.
Crestron MPS-250 Multimedia Presentation System 250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 12 REC OUT (1) 5-pin 3.
Multimedia Presentation System 250 Crestron MPS-250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 17 IR/SERIAL OUT (4) 2-pin 3.5 mm detacha ble terminal blocks, IR/Serial output ports; IR o utput up to 1.
Crestron MPS-250 Multimedia Presentation System 250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 25 TOUCH PANEL OUT Contains one CH port an d one QM port.
Multimedia Presentation System 250 Crestron MPS-250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 27 COM A & B (2) DB9 male, bidirectional R S-232 ports; Up to 115.2k baud, har dware and soft ware handshaking support f or communic ation with serial devices.
Crestron MPS-250 Multimedia Presentation System 250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 29 OUTPUT 1-4 Contains composite, S-video (Y/ C), component (Y, P b , P r ) and RGBHV outputs o n six BNC connectors and on e DB15HD connector.
Multimedia Presentation System 250 Crestron MPS-250 Connectors, Controls, & Indicators (Continued) # CONNECTO RS 1 , CONTROLS & INDICATORS DESCRIPTION 33 100 – 240V ~2. 5A 50/60 Hz (POWER SUPPLY) (1) IEC Socket, mates w ith removable power cord (included).
Crestron MPS-250 Multimedia Presentation System 250 Industry Compliance This unit has been manufactured to comply with UL’s Standards for Safety in Canada and t he United States .
Multimedia Presentation System 250 Crestron MPS-250 Setup Network Wiring When wiring the Cresnet ® and Ethernet network, consider the following: • Use Crestron Certified Wire. • Provide sufficient power to the system. CAUTION: Insufficie nt power can lead to unpre dictable results or damage to the equipment.
Crestron MPS-250 Multimedia Presentation System 250 CresCAT-QM Cable NOTE: Do not unt wist the t wo wires in a s ingle pair fo r more than 1/3-1/2” (0.84-1.27 cm ) when m aking a connecti on. The twists are critical to canc eling out interference between t he wires.
Multimedia Presentation System 250 Crestron MPS-250 QM Network Topology T P S-12G /15 G - Q M - L MP S - 250 QM QM QM O r ig in a tio n P oi n t s E ndp oi nts QM M i dpo in ts MP S - 250 MP S - 250 QM -M D 7 x 2 Installation Ventilation The MPS-250 should be used in a well-vent ilated area.
Crestron MPS-250 Multimedia Presentation System 250 2. Position a rack ear so that its mounti ng hole s align with the holes vacated by the screws in ste p 1. 3. Secure the ear to the unit with three screws from step 1, as shown in the following diagram.
Multimedia Presentation System 250 Crestron MPS-250 Hardware Connections for the MPS-250, Front Hardware Connections for the MPS-250, Rear When runni ng the out- of-the-bo x program , the MPS-25 0 can.
Crestron MPS-250 Multimedia Presentation System 250 CAUTION: Al l source devi ces should be grounded t o the MPS- 250. NOTE: The MPS-25 0 can only be powered by the included p ower cord. Po wer cannot be supp lied from network de vices that are c onnected to the m ini-term inal block connect ors.
Multimedia Presentation System 250 Crestron MPS-250 Typical Balanced/Unbalanced Ou tputs Shield AMP Left Right + - G + - Balanced Ou tput + + AMP Left Right + - G + - Unbalanced Output + + Configure the RGB Input Ports Each of the RGB input port s feature a set of six DIP switches located ins ide the MPS-250.
Crestron MPS-250 Multimedia Presentation System 250 DIP Switch Location DIP SWITCHES LOCATED UNDER ACCESS PANEL Set the DIP Switches 1. Referring to the following table, set the DIP switches of each RGB input port to the required sync input impedance and DDC functionality.
Multimedia Presentation System 250 Crestron MPS-250 Label the Buttons Use Crestr on Engraver software to p rint custom labels for t he MPS-25 0’s front pa nel buttons and L EDS.
Crestron MPS-250 Multimedia Presentation System 250 Programming Software Have a questi on or comment about Crestr on software? Answers to f requently asked quest ions (FAQs) can be viewed in the Onl ine Help section of the Crestro n website.
Multimedia Presentation System 250 Crestron MPS-250 Configuration Manager Configuration Manager i s the view where program mers “build” a C restron cont rol system by selecting hard ware from t he Device Library .
Crestron MPS-250 Multimedia Presentation System 250 of-the-box functionality program or “custom” for settin gs made when running a custom prog ram) and System Configuratio n.
Multimedia Presentation System 250 Crestron MPS-250 Uploading and Upgrading Crestron recommends using the latest pr ogramming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attem pting to upl oad or upgrade it is necessary to establish communicat ion.
Crestron MPS-250 Multimedia Presentation System 250 TCP/IP Ethernet Communication ETHERNET PC RUNNING CRESTRO N TOOLBOX MPS-250 • Establish USB com munication bet ween MPS-250 an d PC. • Enter the IP ad dress, IP mask and de fault router of the MPS-250 via the Crestron Toolbo x ( Functions | Ethernet Addressing ); otherwi se enable DHCP.
Multimedia Presentation System 250 Crestron MPS-250 Configuration & Operation The MPS-250 can be used f or audio a nd video s witching without any programm ing required. This i s ideal for t hose that need a basic audio- video s witching syst em. Prior to operation, the MPS-25 0 must be configured for use.
Crestron MPS-250 Multimedia Presentation System 250 Exit the Menu To exit the menu: • While in the main menu, press th e MENU button to exit the menu. Exit Menu Prompt Exit Setup Menu? Yes No ⇒ Press the soft button labeled Yes to exit the menu or press the soft button labe led No to return to the menu.
Multimedia Presentation System 250 Crestron MPS-250 The menu is separated int o four section s. • Audio Setup: Contains co ntrols for PROGRAM , SPEECH , and RECORD out put settings, source in put compensat ion, mast er startup volume, and m icrophones.
Crestron MPS-250 Multimedia Presentation System 250 • Press the k or j buttons until “Source Mix” is displayed on the LCD and press ENTER to ope n the Program Source Mix contr ols. Program Source Mix Controls Program Source Mix Aud. Only • Press the k or j buttons until the desired setting is displayed on the LCD.
Multimedia Presentation System 250 Crestron MPS-250 NOTE: While adjusting the Program Bass level, the Program Volume level can be adjusted by turning the volume control clockwise to raise the volume, or counterclockwise to lower the vo lume. When adjusting the volume, the display will change to indicate th e volume level.
Crestron MPS-250 Multimedia Presentation System 250 Program Minimum Volume Control Prog. Min Volume 30% • Adjust the Program Minimum Volume level with the j and k button s. Press the k button to increase the Program Minimum Volume level. Press the j button to lower the Program Minimum Volume level.
Multimedia Presentation System 250 Crestron MPS-250 NOTE: While adjusting the Program Maximum Volume level, the Program Volume level can be adjust ed by turning t he volu me control clockwise to raise the volum e, or co unterclockwise to lower the volume.
Crestron MPS-250 Multimedia Presentation System 250 Program Startup Volume Control Prog. St ar tup Vol . 30% • Adjust the Program Startup Volume level with the j and k buttons. Press the k button to increase the startup volu me level. Press the j butt on to lower the startup volume level.
Multimedia Presentation System 250 Crestron MPS-250 Speech Source Mix Controls Speech Source Mix Aud. Only • Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ Aud.
Crestron MPS-250 Multimedia Presentation System 250 NOTE: While adjusting the Speech Bass level, th e Speech Volume level can be adjusted by turn ing the volume control clockwise to raise th e volume, or counterclockwise to lower the vo lume. When adjusting the volume, the display will change to indicate th e volume level.
Multimedia Presentation System 250 Crestron MPS-250 • Adjust the Speech Delay with the j and k buttons. Press the k but ton to increase the delay. Press the j button to lower th e delay.
Crestron MPS-250 Multimedia Presentation System 250 The MPS-250 ships with the Volume Control Mode set to the Master Vol. setting. When switching the Volume Con trol Mode from the Master Vol. setting to either the Program Only setting, the Speech Only setting, or the user selectable Pgm/Spch Sel.
Multimedia Presentation System 250 Crestron MPS-250 Speech Minimu m Volume Contro l Spch. Min Vol ume 30% • Adjust the Speech Min imum Volume level with the j and k butt ons. Press the k button to increase the Speech Minimum Volume level. Press the j button to lower the Speech Minim um Volume level.
Crestron MPS-250 Multimedia Presentation System 250 • Press MENU or ENTER to save ch anges an d return to th e previo us scr een. Adjust the Speech Startup Volume The Speech Startup Volume co ntrol is used to establish the SPEECH output ’s volume level setting when an input is selected.
Multimedia Presentation System 250 Crestron MPS-250 • Adjust the Record Volume level by turning the volume control clockwise to raise the volume, or counterclockwise to lower the volume. When adjusting the Record Volume level, the display will change to indicate the volume level.
Crestron MPS-250 Multimedia Presentation System 250 Fixed/Variable Control Rec. Fixed/Variable Fixed • Press the k or j buttons until the desired setting is displayed on the LCD. The current setting is indicated with an asterisk (*). The following settings are available: ⇒ Fixed : The RECORD output ope rates at a fi xed level.
Multimedia Presentation System 250 Crestron MPS-250 • Press MENU or ENTER to save ch anges an d return to th e previo us scr een. Input Compensation The compensat ion level of eac h input can be set from the M PS-250’s front panel. The line outputs are not affected by changes made to the inp ut compensation level.
Crestron MPS-250 Multimedia Presentation System 250 • Press MENU or ENTER to save changes an d return to the Select Input to Compensate controls. • Repeat for each input to be adjusted. • Press MENU t o save changes and return to t he Audio Setu p menu.
Multimedia Presentation System 250 Crestron MPS-250 Switch Microphone Gating Microphone gat ing can be i ndividually set on each m icrophone i nput. To swit ch microphone ga ting on or of f: • Access the Micro phone menu as desc ribed on page 53.
Crestron MPS-250 Multimedia Presentation System 250 ⇒ ON : The compression function for the selected microphone input is enabled. • To exit the Microphone Compression co ntrol without saving changes, press MENU . Switch Microphone Lim iter A microphone limit er can be indi vidually set o n each microph one input.
Multimedia Presentation System 250 Crestron MPS-250 • Press the k or j buttons until the desired setting is displayed on the LCD and press ENTER to save the setting. The current setting is indicated with an asterisk (*). The following settings are availab le: ⇒ OFF : Phant om power t o the mi crophone in puts is disa bled.
Crestron MPS-250 Multimedia Presentation System 250 Select Input to Name Sel. Input To Name 1:BNC 1 • Press the k or j buttons until the input to be named is displayed on the LCD and press ENTER . The cursor is placed a fter the last character in the input name.
Multimedia Presentation System 250 Crestron MPS-250 Select Input Type Menu Sel. Input Type 1:BNC 1 • Press the k or j buttons to select the video input to be configured and press ENTER . The current setting is indicated with an asterisk (*). • Press the k or j buttons until the desired input type is displayed.
Crestron MPS-250 Multimedia Presentation System 250 • Press the k or j buttons until the output to be named is displayed on the LCD and press ENTER .
Multimedia Presentation System 250 Crestron MPS-250 Display the IP Address IP Address [000] 000. 000. 000 • Turn the vol ume control clo ckwise or counterclockwise t o select a number in the left-most section of the IP address. You can also press the k or j buttons to select a number.
Crestron MPS-250 Multimedia Presentation System 250 Set the Default Router The MPS-250 can be configured to use a De fault Router f or TCP/IP communications. To set the IP address of the Default Router: • Access the Network Set up menu as described on page 59.
Multimedia Presentation System 250 Crestron MPS-250 • To save the setting and return to the Network Setup menu, press ENTER . To cancel the operation and re turn to the Network Setup menu, press MENU . Set the WINS Mode The MPS-250 can use a WINS server to obta in an IP a ddress.
Crestron MPS-250 Multimedia Presentation System 250 Change the Hostname • Turn the vol ume control clo ckwise or counterclockwise (or press the k or j buttons) to select a new letter (upper case or lowercase) or number. M ove the cursor by pressing the soft buttons labeled < or > .
Multimedia Presentation System 250 Crestron MPS-250 Change the Domain Name corporate.company.c DEL INS < > • Turn the vol ume control clo ckwise or counterclockwise (or press the k or j buttons) to select a new letter (upper case or lowercase) or number.
Crestron MPS-250 Multimedia Presentation System 250 • Press the k or j buttons until “MAC Address” is displayed on the LCD and press ENTER to display the MAC address.
Multimedia Presentation System 250 Crestron MPS-250 Select Function to Name Select Fct. To Name 1:MUTE • Press the k or j buttons until the function to be named is displayed on the LCD and press ENTER . The cursor is placed a fter the last character in the function nam e.
Crestron MPS-250 Multimedia Presentation System 250 ID Devices Prompt Press ENTER to ID all devices. • Press ENTER to continue the identification pro cess, the MPS-250 will clear all device set tings and pr ompt the use r to select the de vice type to be identified.
Multimedia Presentation System 250 Crestron MPS-250 Display the APAD Upgrade Controls Upgrade APAD Yes • To upgra de the APAD , press th e k or j buttons until “Yes” is displayed on the LCD an d press ENTER . The MPS-250 will upgrade the APAD’s firmware (if necessary ) and copy t he required files to the A PAD.
Crestron MPS-250 Multimedia Presentation System 250 • Press the k or j buttons until “Info” is displayed on the LCD and press ENTER to display the Info men u. Display the Info Menu Info REMS HW NET OPS • To view program information, press the soft button lab eled REMS .
Multimedia Presentation System 250 Crestron MPS-250 Display Connected Network D evices 2E: APAD LCD 6-bu << >> ⇒ Press the k or j buttons to s ee other netw ork devices. If the information for a network device is pa rtially displayed, press the soft buttons labeled << or >> to view the rest of the information.
Crestron MPS-250 Multimedia Presentation System 250 Display the Message Controls System log: Top Clear << >> • To scroll through messages in th e log, press the k or j but tons. • To jump to the beginning of th e log, press the soft button labeled Top .
Multimedia Presentation System 250 Crestron MPS-250 Display the Date Controls DATE: 10/16/2006 MO DAY YR ⇒ To set the month, press the soft button lab eled MO . To set the day, press the soft button lab eled DAY . To set the year, press the soft button labeled YR .
Crestron MPS-250 Multimedia Presentation System 250 Restore Default Settings The MPS-25 0 can be restored to its d efau lt factory settings from the fron t panel. Users can select to restore the audio settings or to restore th e audio settings, source names, out put names, and function names.
Multimedia Presentation System 250 Crestron MPS-250 Restore Defaults Menu-All Settings Restore Defaults All settings ⇒ Press the k or j buttons until “All setting s” is displayed on the LCD and press ENTER .
Crestron MPS-250 Multimedia Presentation System 250 Front Panel Lock Controls Front Panel Lock: On • Press the k or j buttons to toggle between On and Off. The current setting is indicated with an asterisk (*). • Press ENTER to save the new setting and retu rn to the Control Setup menu.
Multimedia Presentation System 250 Crestron MPS-250 Raise the Projection Screen Press the button labeled SCREEN UP to raise the projector screen. NOTE: This function will only work if a projection screen’s control lines have been connected to RELAY 1 (up cont rol) and RELAY 2 (do wn control) .
Crestron MPS-250 Multimedia Presentation System 250 Adjust Lighting To set lighting to one of two preset lighting values, press either LIGHTS PRE 1 or LIGHTS PRE 2 . NOTE: This function will only work if a CLS-C6, infiNET switch, or infiNET dimmer was previously identified and connected to the MPS-250 .
Multimedia Presentation System 250 Crestron MPS-250 3. Press the soft button labeled Select to route the source to the projector and touchpanel output. Turn Off the System To turn off the system: 1. Press the Power button. 2. Press the soft button labeled Sys.
Crestron MPS-250 Multimedia Presentation System 250 NOTE: This function will only work if a CLS-C6, infiNET switch, or infiNET dimmer was previously identified and connected to the MPS-250 . The CLS-C6 can be identified as a Cresnet devi ce in the MPS -250 setu p screens as de scribed on page 66.
Multimedia Presentation System 250 Crestron MPS-250 When switching sour ces from the keypad, the MPS-250 will route th e signal to the projector out put and then route the si gnal to the t ouchpanel output. Turn On the System To turn on the system, press any of the so urce buttons on the button p ad.
Crestron MPS-250 Multimedia Presentation System 250 Turn On the System To turn on the system, press any of the source buttons on the control center. The selected source will be rout ed to all of the outpu ts. NOTE: Typically, signal routing information is not d isplayed on the front panel of the MPS-250.
Multimedia Presentation System 250 Crestron MPS-250 Problem Solving Troubleshooting The following table provides corrective action for possible trouble situ ations. If further assistance is required, please contact a Crestron custom er service representative.
Crestron MPS-250 Multimedia Presentation System 250 MPS-250 Troubleshooting (Continued) TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Poor picture quality (Video).
Multimedia Presentation System 250 Crestron MPS-250 8. In the “Address Book” window, click the Add Entry b utton and give the new entry a name (e.g. “System Monitor”). 9. Click the arrow next to the Device Type drop down list. A “Warning” window will open to inform you that this is an advanced feature.
Crestron MPS-250 Multimedia Presentation System 250 Check Network Wiring Use the Right Wire In order to ensure optimum performance over the full ran ge of your installation topology, Crestron Certified W ire and onl y Crestron Certified Wire may be u sed.
Multimedia Presentation System 250 Crestron MPS-250 Reference Documents The latest version of all documents mentioned with in the guide can be obtained from the Crestron website ( www.crestron.c om/manual s ). This link will provide a list of product m anuals arran ged in alpha betical order by model n umber.
Crestron MPS-250 Multimedia Presentation System 250 Software License Agreement This License Agreement (“Agree ment”) is a legal contract betw een you (either an individual or a single business entity) and Crestron Electronics, Inc.
Multimedia Presentation System 250 Crestron MPS-250 If You are a business or organization, You agree that upon request from Crestron or its authorized agent, You will within thirty (30) days fully doc.
Crestron MPS-250 Multimedia Presentation System 250 Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise m ay be returned for credit, ex change or service witho ut prior authorization from CR ESTRON. To obtai n warranty serv ice for CREST RON products, contact an authorized CRESTRON deal er.
Crestron Electronics, Inc. Operations Guide – DOC. 6647A 15 Volvo Drive Rockleigh, NJ 07647 (201992 6) Tel: 888.CREST RON 06.08 Fax: 201.76 7.7576 Specific at ions subject to www.
Ein wichtiger Punkt beim Kauf des Geräts Crestron Multimedia Presentation System 250 MPS-250 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Crestron Multimedia Presentation System 250 MPS-250 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Crestron Multimedia Presentation System 250 MPS-250 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Crestron Multimedia Presentation System 250 MPS-250 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Crestron Multimedia Presentation System 250 MPS-250 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Crestron Multimedia Presentation System 250 MPS-250 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Crestron Multimedia Presentation System 250 MPS-250 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Crestron Multimedia Presentation System 250 MPS-250. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Crestron Multimedia Presentation System 250 MPS-250 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
