Benutzeranleitung / Produktwartung CRAFTSMAN 917.27086 des Produzenten Craftsman
Zur Seite of 60
Owner's Manual (RAFTXM;IN ° 20.5 HP ELECTRIC START 42" MOWER AUTOMATIC LAWN TRACTOR Model No. 917.270860 • Safety • Assembly • Operation • Maintenance • Repair Parts CAUTION: Read and follow all Safety Rules and Instructions before operat- ing this equipment.
Warranty ............................................... 2 Safety Rules ......................................... 2 Product Specifications .......................... 5 Assembly .............................................. 8 Operation ...............
• Slow down beforeturning. • Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. • Turn off blades when not mowing. • S.top engine before removing grass catcher or unclogging chute.
• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to coot before storing. • Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. • Never make adjustments or repairs with the engine running.
PRODUCT SPECIFICATIONS GASOLINE CAPACITY AND TYPE: 3.5 GALLONS UNLEADED REGULAR OILTYPE SAE 30(ABOVE 32°F) _PI-SF/SG/SH): SAE 5W-30 (BELOW 32°F) )ILCAPACITY: W/FILTER: 3.5PINTS W/O FILTER: 3.0PINTS SPARK PLUG: CHAMPION GAP: .030") RJ19LM OR J19LM VALVE INTAKE: .
Parts Bag contents shown full size Locknut 5/16-18 (1) Hex Bolt 3/8-16 x 1 (1) Lockwasher 3/8 (1) Large Flat Washer (1) Hex Bolt 5/16-18 x 1-1/4 (1) Knob (1) Shoulder Bolt 5/16-18 (1) Washer 17/32 x 1.
Seat I Parts packed separately in carton Mulcher Plate Video Cassette Steedng Boot Steering Wheel Manual Parts Bag contents not shown full size I Parts Bag _ "_" i I I Slope Sheet (2) Latch .
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
- .-" - Label INSTALL SEAT Adjust seat before tightening adjustment knob. • Remove cardboard packing on seat pan. • Place seat on seat pan and assemble shoulder bolt. Tighten shoulder bolt securely. • Assemble adjustment knob and flat washer loosely.
Hook Weld Nut Points Lock Washer Weld Nut Latch Hook Latch Washer Plate '_/Screw Washer Nut Shield Latch Hooks TO CONVERTTO BAGGING OR DISCHARGING Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. & ÷ BATTERY CAUTION OR REVERSE FORWARD FAST SLOW WARNING E.
KNOWYOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments, Save this manual for future reference.
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
The cutting height range is approxi- mately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.
• Pull freewheel control out and down into the slot and release so it is held in the disengaged position. • Do not push or tow tractor at more than two (2) MPH.
• Insert key into ignition and turn key clockwise to =START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again.
• Sitting in the traotor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. W'dh motion control lever in neutral (N) position, slowly disengage clutch/ brake pedal.
MAINTENANCE SCHEDULE _-,/_ ._o_ ._JP_'_ __/_,y Check Brake OperaUon _ Check Tire Pressure Check Operator Presence and T Interlock Systems R Check for Loose Fasteners A Sharpen/Replace Mower Blade.
TRAC1OR Always observe safety rules when performing any maintenance. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual).
NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary, TO CLEAN BATI'ERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to "leak" power, Remove terminal guard.
CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. ENGINE COOUNG FINS Remove any dust, dirt or oil from engine cooling fins to prevent engine damage from overheating.
_CAUTION: Before performing any service or adjustments: • Depress clutch/brake pedal fully and set parking brake. • Place motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key.
TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this manual). If tires are over or underinflated, you will not properly adjust your mower.
TO REPLACE MOWER BLADE DRIVE BELT The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL - • Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual).
TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT The motion control lever has been preset - at the factory and adjustment should not be necessary. • loosen adjustment bolt in front of the right rear wheel, and lightly tighten. • Start engine and move motion control lever until tractor does not move forward or backward.
TO START ENGINE WITH A WEAK BATTERY CAUTION: Lead-acid batteries generate explosive gases: Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged.
TO REMOVE HOOD AND GRILL ASSEMBLY • Raise hood. • Unsnap headlight wire connector. • Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.
• While still holding throttle lever against idle speed screw, turn idle mixture screw In (clockwise) until engine begins to die and then turn out (counterclockwise) until engine runs rough.
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. _. CAUTION: Never store the tractor w=th gasoline in the tank inside a building where fumes may reach an open flame or spark.
TROUBLESHOOTING CHART PROBLEM CORRECTION Will not start Hard to start Engine will not turn over Engine clicks but will not start CAUSE • Out of fuel. • Engine not "CHOKED" properly. • Engine flooded. • Bad spark plug. • Dirty air filter.
TROUBLESHOOTING CHART PROBLEM CAUSE CORRECTION Engine clicks but will • Check all wiring. not-start (Cont'd) • Check/replace solenoid or starter. Loss of power Excessive vibration Engine continues to run when operator leaves seat with attachment clutch engaged Poor cut - uneven • Loose or damaged wiring.
TROUBLESHOOTING CHART PROBLEM CAUSE Mower blades will not • Obstruction in clutch rotate mechanism. CORRECTION • Remove obstruction. • Worn/damaged mower • Replace mower drive belt. drive belt. • Frozen idler pulley, • Replace idler pulley.
SCHEMATIC TRACTOR - - MODEL NUMBER 917.270860 I ° J (OPTIONAL) wHiTe I I _ IGNITION IGNmON SWITCH BLACK I J O_O ' _ _ FUSE '_5 AMP. STARTER I ,i- ----'_ "- .
TRACTOR - - MODEL NUMBER 917.270860 ELECTRICAL 41 I I I I 11 I _45 29 12 I I 16 i I I t I I I I I I I I I 34.
ELECTRICAL TRACTOR - - MODEL NUMBER 917.270860 PART NO. NO. DESCRIPTION 1 163465 Battery 2 74760412 Bolt,Hex 1/4-20 x 3/4 8 7603J Tray, Battery 10 145211 Bolt, BtrFront 1/4-20x7-1/2 11 150109 Ho(ddown.
TRACTOR - - MODEL NUMBER 917.270860 CHASSIS AND ENCLOSURES 28 12 14 31 53 3 3 74 36.
TRACTOR - - MODEL NUMBER 917.270860 CHASSIS AND ENCLOSURES KEY PART NO. NO. DESCRIPTION 1 166816 2 140356 3 17060612 4 S'1_551025 5 155272 9 165454)_313 10 _710 11 155_7 12 145660 13 169118 14 17.
TRACTOR - - MODEL NUMBER 917.270860 GROUND DRIVE 77 52 27 22 84 55 105 38.
TRACTOR - - MODEL NUMBER 917.270860 GROUND DRIVE K]EY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 ...... Transaxle (See Breakdown) 66 154778 HydroGr 319-0650 70 134683 2 142431 Spring, Ret.
TRACTOR - - MODEL NUMBER 917.270860 STEERING ASSEMBLY t i i_I _41 I 11_--*_.. d12 ....----17 118 al 47 4O.
TRACTOR -- MODEL N UMBER 917.270860 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 139768 2 154427 3 156483 4 157473 5 6266H 6 121748X 7 19272015 8 12000029 9 3366R 10 156438 11 STD551137 13 154779 .
ENGINE TRACTOR - - MODEL NUMBER 917.270860 14 81 I 32 34 3 13 0 i 17 39 I OPTIONAL EQUIPMENT I Spark Arrester i L • 23 42.
ENGINE TRACTOR - - MODEL NUMBER 917.270860 KEY PART NO. NO. DESCRIPTION 1 162152 2 17720410 3 4 149723 5 144O69 6 144O68 7 138129 8 150176 10 145552 11 STD551125 12 STD522507 13 165287 14 13280336 15 .
TRACTOR - - MODEL NUMBER 917.270860 SEAT ASSEM BLY K]EY PART KEY PART NO. NO. DESCRIPTION NO. NO. Seat 34,50 BIk_k Craftsman 13 121248X Bracket Pnt Pivot Seat (blk) 14 72060412 Bolt Fin Hex 3/8-16unc .
DECALS TRACTOR - - MODEL NUMBER 917.270860 2 3 7 4 1 11 2 9 KL=Y PART NO. NO. 1 156439 2 163205 3 163200 4 163202 6 133644 7 169637 9 163204 11 156811 13 146046 14 15 2O DESCRIPTION KEY PART NO.
TRACTOR -- MODEL NUMBER 917.270860 LIFT ASSEMBLY 27 25 24 38 13 41 i I • ! s 13 5 6 13 32 19 32 49 30 3 2O 7 6 5 4 46.
TRACTOR -- MODEL NUMBER 917.270860 LIFT ASSEMBLY PART NO. NO. DESCRIPTION 1 159460 Lift Lever Inner Wire Asm. 2 159471 Shaft Asm. Lift 3 1G5767X Pin Groove 4 12000002 ERing 5 19211621 Washer 21/32 x 1 x 21 Ga. 6 120183X BearingNyleng 7 125631X Gdp Handle Ruted, 8 122365X Button Plunger Read 11 139865 Link Asm Uft L.
MOWER DECK TRACTOR - - MODEL NUMBER 917.270860 +m' ._C. / _" 40 36 153 1_4 159 "--.,_ >21 21 22 3 24 25 27 48.
MOWER DECK TRACTOR - - MODEL NUMBER 917.270860 KEY PART NO. NO. I 165892 2 S'FD533107 3 138017 4 16548O 5 STD624006 6 130832 8 850857 9 STD551137 10 140296 1! 134149 12 1298_5 13 137645 14 128774.
TRACTOR - - MODEL NUMBER 917.270860 HYDRO GEAR TRANSAXLE .. MODEL NUMBER 319-0650 58 34 139 91 23 19 9OO 18 26 91 28 53 52 14 9O 35 5O.
TRACTOR - - MODEL NUMBER 917.270860 HYDRO GEAR TRANSAXLE - - MODEL NUMBER319-0650 KEY PART KEY PART NO. NO. DESCRIPlr'ION NO. NO. DESCRIPTION 1 142960 Housing, Lower 43 142884 Washer 7/16 x 7/8 x .060 2 142_1 Assembly,Upper Housing 44 150_9 Differential Assembly 3 142932 Seal, Up 52 142991 Washer 3/4 x1.
TRACTOR - - MODEL NUMBER 917.270860 BRIGGS & STRATTON ENGINE-MODEL NUMBER 461707, TYPE NUMBER 0146-EI 1095 VALVE OVERHAUL GASKET SET 12191 61SA_I 634 552A ; 552 4040 1019 LABEL KIT I r 1058 OWNER&.
TRACTOR - - MODEL NUMBER 917.270860 BRIGGS & STRATTON ENGINE-MODEL NUMBER 461707, TYPE NUMBER 0145-E1 51 _ 304 122 1 51A 865 205_ 305_ _4A o 202 _ 50 _ 212 _ 267 t 203_ 861 PUMP REPAIR KIT 307 57__ 425 9681 _J7_ I 1.
TRACTOR - - MODEL NUMBER 917.270860 BRIGGS & STRATrON ENGINE.MODEL NUMBER 461707, TYPE NUMBER 0145-E 697 783 I i051 y 803 544 513 801 802 797 @ 358 GASKET SET 20@ 54.
TRACTOR -- MODEL NUMBER 917.270860 BRIGGS & STRATTON ENGINE-MODEL NUMBER 461707, TYPE NUMBER 0146.E1 KEY PART K]EY PART NO. NO. DESCRIPTION NO. NO.
TRACTOR - - MODEL NUMBER 917.270860 BRIGGS & STRATTON ENGINE-MODEL NUMBER 461707, TYPE NUMBER 0145-E KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 404 223882 Washer (Governor Crank) 82.
57.
.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION I " SIGHTING ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15° MAX. _ Operate your Tractor up end down the face of elopes (not .Jk greater than 15 ), never across the face. Make turns gradu- ally to prevent tipping or loss of control.
For in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME s" (1-800-469-4663) Para pedir servicio de reparaci6n a domicilio 1-800-676-5811 In Canada for all your .
Ein wichtiger Punkt beim Kauf des Geräts Craftsman CRAFTSMAN 917.27086 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman CRAFTSMAN 917.27086 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman CRAFTSMAN 917.27086 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman CRAFTSMAN 917.27086 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman CRAFTSMAN 917.27086 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman CRAFTSMAN 917.27086 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman CRAFTSMAN 917.27086 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman CRAFTSMAN 917.27086. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman CRAFTSMAN 917.27086 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
