Benutzeranleitung / Produktwartung 315.21636 des Produzenten Craftsman
Zur Seite of 26
Owner's Manual 16 in. variablespeed SCROLL SAW Model No. 315.216360 Save this manual for future reference. A, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
• Table of Contents ........................................................................................................................................... 2 • Warranty and Introduction .........................................................
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding.
RULES FOR SAFE OPERATION (Continued) USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
RULES FOR SAFE OPERATION (Continued) KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool. A LARGE PIECE OF MATERIAL SHOULD BE SUPPORTED while cutting.
EXTENSION CORDS Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a consider- able distance from the power source, use an exten- sion cord heavy enough to carry the current that the tool will draw.
Bevel Cut A cutting operation made with the table at any angle other than 90 ° to the blade. Crosscut A cutting or shaping operation made across the grain of the workpiece. Compound Cut A compound cut is a cut made using a miter angle and a bevel angle at the same time.
_lj WARNING: To prevent accidental starting or electrical shock that could cause possible serious personal injury, assemble all parts to your saw before connecting it to power supply. Saw should never be connected to power supply when you are assembling parts, making adjustments, lubricating, installing or removing.
The following labels are on the scroll saw with locations indicated. WARNING ON OFF a CRRFTSMRN ° Consumer Help Line 1-800-932-3188 WARNING / ADVERTENCIA Fig.
This versatile variable speed scroll saw isgreat for making toys, puzzles, games, artwork, and jewelry. It is a handy do-it-yourself tool. It cuts wood, wood composition products, plastic, and other fibrous material up to2 inches thick. It also cuts nonferrous metals (aluminum, brass, copper).
HOLD DOWN FOOT/BLADE GUARD The hold down foot should be lowered until it just rests on top Of the workpieoe to prevent the workpieco from lifting while cutting, but not so much that the workpiece drags. The vertical portion provides e blade guard to prevent accidental blade contact.
CLAMPING SCROLL SAW TO WORKBENCH See Figure 7. If the scroll saw is to be used in a portable application, we recommend that you fasten it permanently to a mounting board that can easily be clamped to a workbench or other supporting surface. The mounting board should be of sufficient size to avoid tipping of saw while in use.
SQUARING TABLE TO THE BLADE See Figures 9 and 10. • Loosen the hold down foot lock knob and move hold down rod all the way up. Tighten knob. • Loosen the table lock knob and move the table untit it is approximately perpendicular, or at right angle to the blade.
HEX BOLT SAW TABLE HEX NUT ERO DEGRE STOP ASSEMBLY Fig. 11 The zero stop assembly can be rotated to the left and down out of the way and the table can be angled up to 12' to the left. See Figure 12. Note: Make sure the zero degree stop is rotated all the way down or it will contact the blade storage drawer as you angle to the left.
Loosen the foot adjusting knob. See Figure 13. To center the hold down foot around the saw blade, slide the hold down foot to the side. Tighten the foot adjusting knob. Position blade and securely tighten blade knob. Turn the quick release knob to the right or clockwise to tension the blade.
This scroll saw is designed to cut wood, wood compo- sition products, plastic, and nonferrous metals (alumi- num, brass, copper). GENERAL OPERATION Please read and understand the following items concerning your scroll saw before attempting to use the saw.
LOCK POST See Figure 17. To prevent unauthorized use of your scroll saw, we suggest that you disconnect it from the power supply and lock the knob in the OFF position. A Master Lock® 105D padlock should be used. When the lock is installed and locked, as illustrated, the switch is inoperable.
STACK CUTTING See Figure 19. After becoming well acquainted with your saw through practice and experience, you may wish to try stack cutting. Stack cutting may be used when several identical shapes need to be cut. Several pieces of wood may be stacked on top and secured to each other before cutting.
Properly support round material such as dowel rods. They have a tendency to roll during a cut, causing the blade to "bite." Toavoid this, always use a "v" block. • Clear everything except the workpiece and related support devices off the table before plugging into power and turning the saw on.
• Remove brush cap with a flat blade screwdriver. • Remove brush assembly. Gently pry the brush assembly out using a small screwdriver, point of a nail or paper clip, etc. • Check for wear. If one brush is worn down shorter than 1/4 in., replace both brushes.
21.
CRAFTSMAN SCROLL SAW- MODEL NO. 315.216360 7 40 39 FIGURE A 42 37 i i I 36 _36 16 25 19 23 24 45 46 53_ __ 52.
Po G_ Key No. 1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 26 27 28 Part Number 979817-002 980119-001 979814-001 979813-001 979832-001 981385-001 979809-001 979807-001 979806-001 **S.
ro J_ CRAFTSMAN SCROLL SAW - MODEL NO. 315.216360 29 12 20 "26 24 18 14 12 14 15 37 38 39 40 42 FIGURE B I.
ro ol [ CRAFTSMAN SCROLL SAW- MODEL NO. 315.216360 I The model number will be found on a plate attached to the frame. Always mention the model number in all correspondence regarding your SCROLL | SAW or when ordering repair parts.
In U.S.A. or Canada for in-home major brand repair service: Call 24 hours a day, 7 days a week 1"800-4-MY-HOME s° (1-800-469-4663) Para pedir servicio de reparacibn a domicilio - 1-800-676-5811 Au Canada pour tout le service ou les pi_ces - 1-800-469 4663 For the repair or replacement parts you need: Call 6 a.
Ein wichtiger Punkt beim Kauf des Geräts Craftsman 315.21636 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Craftsman 315.21636 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Craftsman 315.21636 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Craftsman 315.21636 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Craftsman 315.21636 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Craftsman 315.21636 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Craftsman 315.21636 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Craftsman 315.21636. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Craftsman 315.21636 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
