Benutzeranleitung / Produktwartung CMA-44 des Produzenten CMA Dishmachines
Zur Seite of 25
www.cmadishmachines.com.
Table of Contents CMA-44 1. SPECIFICATIONS ................................................................................................. 2 1.1. CMA-44 ................................................................................................
1. S pecifications 1.1. CMA-44 WATER CONSUMPTION PER RACK (FINAL RINSE) .8 GAL. .94 GAL. PER HOUR (FINAL RINSE) 192 GAL. 192 GAL. CONVEYOR SPEED FEET PER MINUTE 6.
Getting Started 2. Getting S t arted 2.1. Introduction to CMA-44 The CMA-44 is designed to give maximum cleaning in 44 inches. It represents the cleaning power of machines twice i ts length. The curtains incorporate d in the machine minimize tra nsfer from tank to tank during the wash and sanitizing pro c edures.
Getting Started 2.2. Receiving and Installation When you receive your new CMA-44, complete the assembly by installing the scrap tray assembly with its overflow chut e, the two wrapper shi elds and the curtain ro ds, which are shipped inside the machine.
Getting Started 2.3. Receiving and Installation (Old Models) When you receive your new CMA-44, complete the assembly by installing the scrap tray assembly with its overflow chut e, the two wrapper shi elds and the curtain ro ds, which are shipped inside the machine.
Getting Started 2.3.1. Electrical * A 3-phase 208-240 volt AC, 60 Hz dedicated circuit should be used to supply electri cal energy to the CMA-44 dishwasher (see specification sheet page 2 ). Connect the wire that has the highest voltage (stinger lead) to the main contactor’s po wer terminal L2 .
Getting Started P/N 13505.12 205 RACKS ( CMA-44H ) 242 RACKS ( CMA-44L ) P/N 13505.10 OLD Models Figure 2.3.3 b 4. On a 3-phase machine the water pump motors are al so 3-phase and, dependin g on which terminal each phase is co nne cted to, the motor can rotate in either direction.
Getting Started 2.3.4. Scrap Tra y Assembl y and Overflow Chute Installation The scrap tray assembly and overflow ch ute, whi ch came packaged inside the machine, can easily be installed by executing the foll owing steps: Figure 2.
Getting Started 2.3.5. Pump Impeller Note Figure 2.2.5 Installation: When installing the water pump imp eller the Nylon Lock Nut indicated by the arro w in Fig ure 2.2.5 must be in place to prevent the impeller from spinn ing off of the shaft and damaging the motor.
Getting Started 2.3.6. Optional Hood Adapter (Set of Two) An optional Hood Adapter set (P/N 13901.82) i s available. The di mensions for proper installation are given belo w. 53-½" 9-½" 65" Leg Adj 66” Vents Measure 4” x 16” MODEL CMA-44 Installatio n & Operation Manual Rev.
Getting Started 2.3.7. Optional Freestanding Scrap Trap and Adaptor Kit The optional Freestandi ng Scrap Trap (P/N 0156 0.00) and Adaptor Kit (P/N 13512.
Getting Started 2.3.8. Field Installed Accessories Installation of the accessory chemi cal pumps must be pe rformed by qualified personnel. 2.3.8.1. Chemical Dispensers 1.
Getting Started 2.4. Safety Tips for the CMA-44 DA NGE R: Always turn off the circuit breaker at the wall when working on this dishmachine. Even with the machine’s po wer switch off there is a live connection coming to the switch, so turn off the circuit breaker a s well.
Operation 3. Operation 3.1. Initial Setup 3.1.1. Auto Fill Timer/ Auto Re- Fill Timer Both timers for the CMA-44 are set at the factory. When the po wer button is activated, the machine should fill until it begi ns to overflow into the scrap tray, at which point it should stop filling.
Operation 3.2. Beginning Operation To run the dishmachine, perform the following step s: 1. Close both d r ains (valve h andles in vertical position). CLOSE CLOSE 2. Turn on the p ower to the dishmachine. T he machine will begin its (adjustable) timed auto-fill.
Operation 5. At the end of the shift and after heavy period s of accumulation, clean the three strainer trays inside the machine. Also, at the end of each shift, remove and clean the six spray arms. Then reinstall them into the machine. Also, when water becomes heavily soiled, drain the ta nks and refill the machine.
Operation pressure regulator is adjusted to 20-PSI. This allows 0.8 (CMA-4 4L), or 0.94 (CMA-44H) gallons of water to enter the machine each time a ra ck is washed. It is recommended that the 5-1/2% c hemical solution be standardized to allow uniform dispensing of the sanitizing sol ution into the flow of rinse water as the machine operates.
Operation 7. Place a rack into the machine and observe the spray pattern of the pre-wa sh, the wash, and the final rinse. a. Check the titration of the wash tank at this point. b. While the rack is in the fin al rinse, chec k for 50 PPM resid ual chlorine in the final rinse.
Operation 3.4. Quick service guide MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 19 MODELS: CMA 44/ 66 CONVEYOR (S) TECHNICA L ISSUE CAUSE SOLUTION Continuously cyc les Manual/auto switch in MANUAL mode or faulty Turn switch to AUTO position or replace Conveyer t imer faulty Replace timer, P/N 13418.
Operation 3.5. Trouble Shooting PROBLEM LIKELY CAUSE SOLUTION Pre-wash/power wash motor inoperative Bad motor or capacitor Faulty contactor Replace defect ive motor Replace contactor Fuse is burned ou.
Customer Notice 4. CMA-44 Customer Notice MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 21.
Customer Notice TIPS TO SAVE A SERVICE CHARGE If the Lessee of this equipment initiates a service call and it is sub sequently determined that the problem does not relate to part failure or out of chemical s, there will be a mini mum service ch arge for a service person to respond.
Electrical Diagrams 5. Electrical Diagram MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 23.
Electrical Diagrams 6. Electrical Diagram (Old Models) MODEL CMA-44 Installatio n & Operation Manual Rev. 2 .15 10/18/07 Page 24.
Ein wichtiger Punkt beim Kauf des Geräts CMA Dishmachines CMA-44 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie CMA Dishmachines CMA-44 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für CMA Dishmachines CMA-44 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von CMA Dishmachines CMA-44 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über CMA Dishmachines CMA-44 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon CMA Dishmachines CMA-44 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von CMA Dishmachines CMA-44 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit CMA Dishmachines CMA-44. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei CMA Dishmachines CMA-44 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
