Benutzeranleitung / Produktwartung 2004 Town and Country des Produzenten Chrysler
Zur Seite of 401
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
.
INTRODUCTION CONTENTS m Introduction ........................... 4 m How T o Use This Manual .................. 4 m W arnings And Cautions ................... 6 m V ehicle Identification Number ............... 6 m V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys .................. 1 2 ▫ Ignition Key Removal ................... 1 2 ▫ Key-In-Ignition Reminder ................ 1 3 m Sentry Key ............................ 1 3 ▫ Replacement Keys .
m V ehicle Theft Alarm — If Equipped ........... 2 7 m Sliding Side Door ........................ 2 8 ▫ Power Sliding Door — If Equipped ......... 3 0 ▫ Child Protection Door Lock ............... 3 2 m Liftgate ............................... 3 4 ▫ Power Liftgate — If Equipped .
m Safety T ips ............................ 7 3 ▫ Exhaust Gas .......................... 7 3 ▫ Safety Checks Y ou Should Make Inside The V ehicle .............................. 7 4 ▫ Periodic Safety Checks Y ou Should Make Outside The V ehicle .
A WORD ABOUT YOUR KEYS Y ou can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer .
NOTE: The power window switches, radio, power outlets, and removable console (if equipped), will r emain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle fr ont door will cancel this feature. W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regar dless of whether or not the vehicle is locked or unlocked.
All of the keys provided with your new vehicle have been programmed to the vehicle electr onics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
NOTE: • The front courtesy over head console, door courtesy and liftgate lights do not turn on if the dimmer control is in the interior lights ON position (extreme top position). • The illuminated entry system will not operate if the dimmer control is in the “defeat” position (extr eme downward position).
W ARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
If you press the power door lock switch while the sliding door is open, the sliding door will lock. Automatic Door Locks — If Equipped The doors will lock automatically on vehicles with power door locks if: 1. The transmission is in gear , 2. all doors ar e closed, 3.
4. any door is opened (excluding liftgate) and 5. the vehicle speed is 0 mph (0 km/h). The Auto Unlock feature can be enabled or disabled by performing the procedur e in the Overhead Console, Customer Programmable Featur es section. NOTE: Use the Auto Door Locks and Auto Unlock features in accor dance with local laws.
Six button transmitters will provide functions that allow the same basic operation as the three button, but may also be used to Open/Close the optional power liftgate, left power sliding door , or right power sliding door .
T o unlock the doors and liftgate: Press and r elease the UNLOCK button on the transmitter once to unlock the driver’s door side of the vehicle, or twice to unlock all doors and liftgate.
headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on. The panic alarm will stay on for 3 minutes unless you turn it off by pr essing the P ANIC button a second time or by turning the ignition switch to the ON position.
T o Open/Close Right Power Sliding Door — If Equipped Press the RIGHT button twice within five seconds to open/close the right power sliding door . If the button is pushed while the door is being power closed, the door will reverse to the full open position.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed op- eration.
T ransmitter Battery Service The recommended r eplacement battery is one CR2032 battery . NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit boar d. 1. W ith the transmitter buttons facing down, use a thin coin to pry the two halves of the transmitter apart.
VEHICLE THEFT ALARM — IF EQUIPPED This system monitors the vehicle doors and ignition switch for unauthorized entry or operation. When the alarm is activated, the system provides both audible and visual signals.
NOTE: • The driver’s door and liftgate key cylinders cannot arm or disarm the system. • Once the alarm is set, and the liftgate button on the keyless entry transmitter is pressed, on a non-power liftgate vehicle, you have a 30 second one time access into the liftgate area.
T o keep your door operating properly , observe the fol- lowing guidelines: • Always open the door smoothly . • A void high impacts against the door stop when open- ing the door . This is very important when your vehicle is parked on an incline as the door will slide faster in the downhill direction.
NOTE: The driver’s side sliding door cannot be opened while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door .
rear seat passengers. Pr essing the switch once will open the power sliding door , once the door is fully open pressing the switch a second time will close the door .
• The power sliding door switches will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • If the power sliding door encounters multiple obstruc- tions within the same cycle, the system will automati- cally stop and must be opened or closed manually .
When the child lock system is engaged the door can be opened only by using the outside door handle or the switches located on the trim panel just in front of the power sliding door , even though the inside door lock is in the unlocked position.
LIFTGA TE NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. T o open the liftgate, insert the key into the lock and turn to the right.
NOTE: On vehicles without power locks, the liftgate can only be opened using the vehicle keys. The key must be held in the unlocked position for the liftgate to open. Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter .
W ARNING! During power operation, personal injury or cargo damage may occur . Ensure the liftgate travel path is clear . Make sure the liftgate is closed and latched before driving away .
• If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually . W ARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle.
WINDOWS Power V ent Windows Switches on the driver’s door trim panel let the driver operate the two vent windows from the driver’s seat. Power Windows Y ou can control either fr ont window using switches on the driver’s door trim panel. There is a single switch on the passenger’s door trim panel which operates the passenger door window .
Auto Down Feature — If Equipped The driver’s window switch has an auto down feature. Press the window switch past the detent, r elease, and the window will go down automatically . T o open the window part way , press the window switch part way and release it when you want the window to stop.
W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly .
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the r ear seats. Grasp the latch plate and pull out the belt.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
4. Position the lap belt acr oss your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
6. T o release the belt, push the r ed button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
As a guide, if you are shorter than average, you will prefer a lower position, and if you ar e taller than average, you’ll prefer a higher position. When you r elease the anchorage, try to move it up or down to make sure that it is locked in position.
2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upwar d over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
Center Lap Belts The center seating positions have a lap belt only . T o fasten the lap belt, slide the latch plate into the buckle until you hear a “click”. T o lengthen the lap belt, tilt the latch plate and pull. T o remove slack, pull the loose end of the webbing.
NOTE: These devices are not a substitute for pr oper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly . The pretensioners ar e triggered by the front airbag con- trol module (see Fr ont Airbag Section).
Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seatbacks, and their seatcovers are labeled SRS AIRBAG. W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them.
Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, fr ont airbags work with the instrument panel knee bolsters to pr ovide improved protection for the driver and fr ont passenger . Side airbags also work with seat belts to improve occupant pr otection.
2. All occupants should wear their lap and shoulder belts properly . 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door , airbags will inflate forcefully into the space between you and the door .
The Front Airbag System consists of the following: • Front Airbag Contr ol Module (with integrated side impact sensor - if equipped) • AIRBAG Readiness Light • Driver Airbag • Front Passenger .
The front airbag contr ol module sends a message to the instrument cluster to turn on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition switch is first turned ON, then turns the light off.
Side Airbags Supplemental Restraint System (SRS) — If Equipped The Side Airbag System, if equipped, consists of the following: • AIRBAG Readiness Light (shared with the fr ont airbag system) • S.
If An Airbag Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-sever e col- lision, to help restrain the driver and fr ont passenger , and then immediately deflate. NOTE: A collision that is not sever e enough to need airbag protection will not activate the system.
W ARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags and seat belt pretensioners replaced by an autho- rized dealer as soon as possible.
Airbag Light Y ou will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately .
Children 12 years and under should ride pr operly buck- led up in a rear seat. According to crash statistics, children ar e safer when properly restrained in the r ear seats, rather than in the front. W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle.
used either rearwar d-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearwar d-facing direction than infant carriers do, so they can be used rearwar d-facing by children who weigh mor e than 20 lbs (9 kg) but are less than one year old.
W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
• In the rear seat, you may have tr ouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle end of the belt several times to shorten it.
Lower Anchors and T ether for CHildren (LA TCH) Each vehicle, except commercial car go vehicles, is equipped with the child restraint anchorage system called LA TCH, which stands for Lower Anchors and T ether for CHildren. T wo LA TCH child restraint anchor- age systems are installed on all second-r ow seats.
When using the tether anchorages in the outboard seat- ing positions, ensure that the strap is r outed over the top of the seatback and under the head restraint between the head restraint posts. When the tether anchorage is used in the center seating position, the strap should be posi- tioned straight over the top of the seatback.
Fleet vehicles equipped with the LA TCH system on the 3-passenger bench seat must have the seat adjusted to the full rear position on the tracks when the LA TCH system is used. Also, when using the LA TCH system, be sure the seatback is two clicks rear of its full upright position.
W e urge that you car efully follow the directions of the manufacturer when installing your child r estraint. Many , but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector and a means for adjusting the tension in the strap.
• Check belt fit periodically . A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. If this doesn’t help, move the child to the center rear seating position and use the lap belt.
W ARNING! Rear Facing Infant restraints must never be secured in the passenger seat of a vehicle with a passenger airbag. In an accident a passenger airbag may deploy causing severe injury or death to infants riding in rear facing infant restraints.
with the seat adjusted to the rear most position. Never allow children to slide the shoulder belt behind them or under their arm. T ether Installation For Commercial V ehicles W ith Rear Seat Delete T o secure the child r estraint upper tether strap to the vehicle, follow the instructions shown: 1.
2. Extend the child r estraint tether anchor forward to- wards the fr ont passenger seat. 3. Follow the child r estraint manufacturer’s directions for proper use of connecting the child r estraint to the extended tether strap.
6. Using the hook attached to the child r estraint tether strap, attach the child restraint tether strap to the metal ring on the vehicle tether anchor . 7. Following the child seat manufactur er’s instructions, tighten the child restraint tether strap.
While cruising, brief full-thr ottle acceleration, within the limits of local traffic laws, contributes to a good br eak-in. W ide open throttle acceleration in low gear can be detrimental and should be avoided. The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant.
W ARNING! If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts.
Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil or other fluid leaks.
.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Mirrors ............................... 8 1 ▫ Inside Day/Night Mirror ................. 8 1 ▫ Automatic Dimming Mirror — If Equipped .... 8 2 ▫ Driver’s Side Outside Mirror Auto Dimmer — If Equipped .
▫ Manual Reclining Seats — If Equipped ....... 8 8 ▫ Manual Lumbar — If Equipped ............ 8 9 ▫ Middle Quad Fold & T umble Seating ........ 9 0 ▫ Middle Quad Fold & T umble Seat Removal .... 9 0 ▫ 50/50 Fold & T umble Rear Seat Removal .
▫ Front Fog Lights — If Equipped ........... 1 1 0 m Multifunction Lever ..................... 1 1 0 ▫ T urn Signals ......................... 1 1 0 ▫ Headlight Low/High Beam Selector Switch . . . 1 1 1 ▫ Passing Light ......................
m Garage Door Opener — If Equipped ......... 1 2 9 ▫ Programming Homelink ................ 1 3 0 ▫ Canadian Programming/Gate Pr ogramming . . 133 ▫ Using Homelink ...................... 1 3 3 ▫ Erasing Homelink Buttons ............... 1 3 4 ▫ Reprogramming a Single Homelink Button .
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view thr ough the rear window . A two point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle).
Automatic Dimming Mirror — If equipped If the switch is in the “Auto” position the mirror will automatically adjust for annoying headlight glare fr om vehicles behind you. Y ou can turn the feature on or off by pressing the button at the base of the mirr or .
Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror . Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle.
Power Remote-Control Mirrors Use the mirror select switch, located on the instr ument panel to the left of the steering column, to adjust the view obtained in the outside mirrors. Pr ess the rocker switch to the L or R for Left or Right mirror selection.
SEA TS Manual Front Seat Adjuster The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressur e, move forward and rearwar d on the seat to be sure the seat adjusters have latched.
8–W ay Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the outboard side of the seat. The fr ont switch controls up/down, forward/r earward, and tilt adjustment. The rear switch contr ols the seatback recline adjustment.
Adjustable Head Restraints — If Equipped Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Pull up or push down on the head restraint so that the upper edge is as high as practical. T o raise the head restraint, pull up on the head restraint.
Heated Seats — If Equipped This feature heats the fr ont driver and passenger seats. The controls for the heated seats ar e located on the instrument panel above the radio. Y ou may choose LOW , HIGH or No Heat. The switch position as well as an indicator light will show when the LOW or HIGH heat is ON.
W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Middle Quad Fold & T umble Seating The passenger’s and driver’s side middle quad seats can be tilted forward for easy access to the thir d seat or rear cargo ar ea. T o tilt the seat, pull up on the release handle and tilt the seat fully forward.
3. Pull up on the seatback r elease lever located on the outboard side of the seat and fold the seatback down. If the head restraint contacts the r ear of the front seat, move the front seat forwar d on its tracks. 4. Pull up on the r elease handle and tumble the seat fully forward.
5. Pull the r elease bar located at the bottom front edge of the seat to disengage the front attachments. 6. The seat assembly can now be r emoved from the vehicle and moved on its Easy Out t Rollers. T o reinstall the seat, r emove any obstructions from the floor in front of the seat and ensur e the head restraint is in its full downward position.
50/50 Fold & T umble Rear Seat Removal 1. Lower the head r estraint and pull up on release lever “1” to fold the seatback down. 2. Pull up on r elease lever “2” and tumble the seat fully forward.
3. Pull the r elease strap “3” located at the bottom of the seat to disengage the front attachments. 4. The seat assembly can now be r emoved from the vehicle and moved on its Easy Out t Rollers.
3 – Passenger Bench Seats Release levers are located on the r ear leg assemblies, near the floor . T o remove the seat, squeeze each r elease handle and rotate downwar ds to deploy the wheels. A lock indicator button pops up when the seat is unlocked.
Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all r ear seats and some front seats.
Rear Seat Descriptions 7 Passenger Model — 2– passenger bucket seats in the second position and 3– passenger bench seat or 50/50 bench seat in the third position. All rear seats ar e remov- able. Rear Bench Seating Flexibility The 3– passenger bench seat may be adjusted to any of 3 positions on its tracks while installed in the vehicle.
3. Additional Storage— The 2nd and 3rd r ow seats installed. The 3rd row bench seat is in the full forward position on the tracks and one or both of the rear seatbacks ar e folded down. 4. Auxiliary Seating— The middle quad seats are r emoved from the vehicle.
Rear Quad and 50/50 Seating Flexibility The seats may be used with either or both seatbacks folded forward for additional storage space, or with either or both seats removed fr om the vehicle. Both 50/50 seats may also be moved to the 2nd row seating position when the middle quad seats are r emoved.
3. Additional Storage— The 2nd row seats ar e installed in the middle seating position. Either or both of the rear seats ar e removed from the vehicle. 4. Auxiliary Seating— The 2nd row seats ar e removed from the vehicle. Then the third r ow seats can be installed in either the rear or middle seat position.
W ARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating posi- tion. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat.
Y our vehicle may have been delivered with two Remote Keyless Entry transmitters. One or both transmitters can be linked to either memory position. The memory system can accommodate up to four transmitters, each one linked to either of the two memory positions.
9. Pr ess and release the LOCK button on one of the transmitters. A chime will sound signaling to you that the transmitter has been successfully linked to memory .
T o Disable A T ransmitter Linked to Memory 1. T urn the ignition switch to the OFF position and remove the key . 2. Pr ess and release memory button number 1. The system will recall any memory settings stor ed in position 1. W ait for the system to complete the memory recall before continuing to step 3.
TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Next, push to the left the safety catch located under the front edge of the hood, near the center .
W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Y ou could have a collision. Be sure all hood latches are fully latched before driving.
by pressing the lens. The lights will r emain on until the lens is pressed a second time, so be sur e they have been turned off befor e leaving the vehicle. The interior lights will automatically turn off in about 15 minutes if any of the following occur .
Dome Light Position Rotate the dimmer control com- pletely upward to the second de- tent (extreme top position) to turn on the interior lights, except the front r eading/courtesy lights. The interior lights will remain on when the dimmer control is in this position.
ON for up to 90 seconds after you turn the ignition switch OFF . T o turn the Automatic System OFF , turn the headlight switch clockwise to the OFF position. NOTE: The engine must be running befor e the head- lights will come ON in the Automatic mode.
headlights within 45 seconds. The 90 second delay inter- val begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled. If the headlights are turned of f before the ignition, they will turn off in the normal manner .
T urn Signal W arning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about one mile with the turn signals on, a chime will sound to alert the driver . Headlight Low/High Beam Selector Switch Pull the multifunction lever toward the steering wheel to switch the headlights between HIGH and LOW beam.
NOTE: Always remove any build-up of snow that prevents the windshield wiper blades fr om returning to the OFF position. If the windshield wiper switch is turned OFF and the blades cannot return to the OFF position, damage to the wiper motor may occur .
W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshield with defroster before and during wind- shield washer use.
TIL T STEERING COLUMN — IF EQUIPPED T o tilt the column, pull the small lever , located behind the turn signal control, towar d you and move the wheel up or down, as desired. Release the lever to lock the wheel firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous.
TRACTION CONTROL SWITCH — IF EQUIPPED The TRAC indicator , located below the instrument cluster odometer , will light up when the T raction Control is in use. T o turn the system OFF , press the TRAC OFF switch located on the steering column, until the TRAC OFF indicator below the instrument cluster odometer lights up.
ADJUST ABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away fr om the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position.
• The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control System is ON. The following messages will be displayed on vehicles equipped with the Electronic V ehicle .
T o Activate: Push the “ON/OFF” button once and the CRUISE indi- cator located below the instrument cluster odometer will illuminate showing the electronic speed contr ol system is on. T o turn the system OFF , push the “ON/OFF” button again and the system and indicator will turn off.
T o V ary the Speed Setting: When the speed control is set, speed can be incr eased by pressing and holding the “RESUME/ACCEL” button. When the button is released, a new set speed will be established. T apping the “RESUME/ACCEL” button once will result in a 2 mph (3 km/h) speed increase.
W ARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Y our vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy , snow-covered, or slippery .
The lights also turn on when a front door , a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry , the lights will also turn on when the unlock button on the transmitter is pressed. The area ar ound the instrument panel cupholders is also illuminated from a light in the over head console.
turns in an area fr ee from large metal or metallic objects, the “CAL” symbol will turn off and the compass will function normally . Manual Compass Calibration If the compass appears erratic and the “CAL” symbol does not appear , you must put the compass into the Calibration Mode manually .
T o set the variance: T urn the ignition switch ON and set the display to Comp/T emp. On vehicles equipped with a Compass/Mini T rip Computer press the RESET button for approximately 5 seconds. On vehicles equipped with Compass/T emp press and hold the C/T and US/M buttons for 5 seconds.
Mini-T rip Computer This displays information on the following: • A verage Fuel Economy (ECO A VG) Shows the average fuel economy since the last reset. • Distance T o Empty (DTE) Shows the estimated distance that can be travelled with the fuel remaining in the tank.
Electronic V ehicle Information Center (EVIC) — If Equipped The Electronic V ehicle Information Center , when the appropriate conditions exist, displays the following W ARNING messages and symbols.
NOTE: T ire pressur e menu items are available only on vehicles equipped with the T ire Pressur e Monitor Sys- tem. Customer Programmable Features — If Equipped Press the “MENU” button until one.
the T ire Pressur e Monitor system and the training routine is not performed, training will be cancelled after one minute or the next time you cycle the ignition key .
Remote Linked T o Memory (A vailable with Memory Seat and Pedals Only) When this feature is selected, pr essing the Unlock button on any Remote Keyless Entry transmitter already linked to memory will .
Headlamp Delay When this feature is selected the driver can choose, when exiting the vehicle, to have the headlamps remain on for 30, 60, or 90 seconds, or not remain on. Pr essing the “STEP” button when in this display will select 30, 60, 90, or “OFF .
W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards.
W ARNING! V ehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver . Exhaust gas can cause seri- ous injury or death. W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver .
NOTE: Some gate operators and garage door openers may requir e you to replace this Programming Step 3 with procedur es noted in the 9 Gate Operator/Canadian Pro- gramming 9 section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal fr om the hand-held transmitter .
and, depending on the brand of the garage door opener (or other rolling code equipped device), r epeat this sequence a third time to complete the pr ogramming. HomeLink should now activate your rolling code equipped device. NOTE: T o program the r emaining two HomeLink but- tons, begin with 9 Programming 9 step two.
etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there ar e still programming difficulties or questions, contact HomeLink at: www .
This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received including interfer ence that may cause undes- ired operation.
switch rearwar d will activate the Express Open Feature, causing the sunroof to open automatically . Press and hold the button located to the right of the sunroof switch, to open the vent. The sunr oof can be stopped at any position between closed and full vent.
W ARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. Y ou could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof.
ELECTRICAL POWER OUTLETS — IF EQUIPPED T o the left of the instrument panel cup holder are two 12 volt power outlets. The upper outlet is controlled by the ignition switch and the lower outlet is connected directly to the battery .
The lower outlet is protected by an automatic r eset circuit breaker . The automatic circuit br eaker restores power when the overload is removed. The cir cuit breaker also supplies power to the outlet in the removable floor console, when in the front position.
CONVENIENCE TRA Y DRA WER AND CUP HOLDERS Instrument Panel Cup Holders The instrument panel cupholders ar e located in a pull out drawer just below the climate controls. When the drawer is pulled out firmly , the arms of the cupholders will spring out.
W ith the optional dealer installed Smoker’s package, a removable ash r eceiver is inserted into the convenience tray location. T o install the ash receiver , slide the forward edge into the convenience tray opening and push down to lock it into position.
• The quad seat cupholders are designed to br eak away if stepped on. T o return the cupholder to its normal position, simply push the cupholder up to snap it into place. • The floor mat must be in position for optimum cup- holder operation. There ar e also two cupholders and a flat tray on the seat back of the quad seats.
breaker and is power ed directly from the battery , items plugged into this outlet may discharge the battery and/or prevent engine starting. T o remove the console use the following pr ocedure: 1.
T o reinstall the console, r emove the rubber mat and relocate to the alternate floor tray , slide the console forward to engage the fr ont of the console into the floor tray . Rapidly push down on the rear of the console with enough force to engage the latch, you should hear the latch “snap” into place.
CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e. cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
The liftgate sill plate has a raised line with the statement “Load T o This Line”. This line indicates how far rearwar d cargo can be placed without interfering with liftgate closing.
1. T o raise the cargo or ganizer pull up on the handle and pull towards the r ear of the vehicle. 2. Place the r ear corners of the cargo organizer into the supports located on the rear trim panel. Pr ess down on the back of the cargo or ganizer to lock it into place.
CAUTION! Do not load objects over 100 lbs (45 kg) in the lower position. Failure to follow this could cause damage to the cargo organizer . T o Open Storage Compartments 1. Pull up on the center opening of the car go organizer . 2. Lift up on the storage compartment dividers and lock into place.
Cargo Organizer removal Unscrew the two plastic fasteners located on the floor of the rear of the car go area and remove the car go organizer from the vehicle.
capacity of the vehicle. Be sure the total load of car go inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity . T o move the cross bars, pr ess the upper edge of each cross bar button pass the detent, then move the cr oss bar to the desired position.
CAUTION! • T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appro- priately .
LOAD LEVELING SYSTEM The automatic load leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the corr ect height.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS m Instruments And Contr ols ................. 1 5 8 m Instrument Cluster W ith T ach .............. 1 5 9 m Premium Instr ument Cluster ............... 1 6 0 m Instrument Cluster Descriptions ............
▫ Power Switch, V olume Control ............ 1 7 1 ▫ Seek Button (Radio Mode) ............... 1 7 1 ▫ T uning ............................. 1 7 1 ▫ PTY (Pr ogram T ype) Button .............. 1 7 2 ▫ Balance ............................ 1 7 3 ▫ Fade .
▫ Program Button 4 (Random Play) .......... 1 7 8 ▫ Mode .............................. 1 7 9 ▫ T ape CD Button ...................... 1 7 9 ▫ T ime Button ......................... 1 7 9 ▫ Scan Button ......................... 1 7 9 ▫ CD Changer Control Capability — If Equipped .
▫ T ime Button ......................... 1 9 7 ▫ Changing Modes ...................... 1 9 7 ▫ Removing Discs From The CD Changer ..... 1 9 7 ▫ CD Changer Operation W ith The Changer Off . . 197 m 6 Disc CD/Digital V ideo Disc (DVD) Changer — If Equipped .
▫ Infrared Thr ee-Zone Automatic T emperature Control — If Equipped ................. 2 1 9 m Rear W indow Features ................... 2 3 0 ▫ Intermittent Rear W iper Operation — Manual T emperature Contr ol Only ............... 2 3 0 ▫ Rear W asher Operation — Manual T emperature Control Only .
INSTRUMENTS AND CONTROLS 158 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER WITH T ACH UNDERST ANDING YOUR INSTRUMENT P ANEL 159 4.
PREMIUM INSTRUMENT CLUSTER 160 UNDERST ANDING YOUR INSTRUMENT P ANEL.
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Low Fuel Light When the fuel level reaches appr oximately 3.0 gallons (1 1.0 liters) this light will turn on and remain on until fuel is added.
NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions. The vehicle should have service performed. If brake failure is indicated, immediate r epair is neces- sary . W ARNING! Driving a vehicle with the brake light on is danger- ous.
8. Anti-Lock Light This light monitors the Anti-Lock Brake System. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.
12. Engine T emperature W arning Light This light warns of an overheated engine condi- tion. If the engine is critically hot, a continuous chime will sound for 4 minutes. After the chime turns off, the engine will still be critically hot until the light turns off.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not requir e towing. The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage.
20. Odometer/T rip Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations r equire that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
When the tire pr essure monitoring system warning light is lit, one or more of your tir es is significantly underin- flated. Y ou should stop and check your tires as soon as possible, and inflate them to the proper pr essure as indicated on the tire and loading information placar d.
will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. High Beam Light This light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low beam.
T wo T ypes of Signals There ar e two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary ... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound.
SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE T APE PLA YER, CD PLA YER AND CD CHANGER CONTROLS — IF EQUIPPED Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
PTY (Program T ype) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn of f. Pressing the PTY button within 5 seconds will allow the program format type to be selected.
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when sear ching for the next PTY station.
AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency . The display will show ST when a stereo station is received.
T o Change From Clock T o Radio Mode Press the T ime button to change the display between radio frequency and time. Operating Instructions — T ape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position.
T ape Eject Press the EJT T ape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the featur e. Changing T ape Direction If you wish to change the direction of tape travel (side being played), press the PTY button.
Operating Instructions — CD Player NOTE: The ignition switch must be in the ON or ACC position and the volume control ON befor e the CD player will operate. CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism.
Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to r eturn to the beginning of the current selection, or r eturn to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
MODE Press the MODE button to select between the tape player , CD player , or satellite radio (if equipped). T o select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds.
Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one curr ently being played. Seek Button Press the SEEK up or down to select another track on the same disc.
• Damaged disc • W ater condensation on optics SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER Radio Operation Power/V olume Control Press the PWR/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume.
channel number will then be displayed for five seconds. The current channel name and number will then be displayed until an action occurs. CD’s may remain in the player while in the Satellite Radio mode. Seek Press and r elease the SEEK button to search for the next station in either the AM or FM mode.
“1–6” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory .
Inserting The Compact Disc CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may either insert or eject a disc with the radio OFF . If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day .
If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not r emoved, the radio will continue to play the non-removed CD. If the CD is removed and ther e are other CD’s in the radio, the radio will play the next CD.
PTY (Program T ype) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn of f. Pressing the PTY button within 5 seconds will allow the program format type to be selected.
Program T ype Radio Display T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode.
SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLA YER AND CD CHANGER CONTROLS Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to incr ease the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
T une Press the TUNE contr ol up or down to increase or decrease the fr equency . If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed.
Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Press the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory .
CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON befor e the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism.
FF/TUNE/R W Press FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased. The R W ( Reverse) button works in a similar manner . Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play .
Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one curr ently being played. Seek Button Press the SEEK up or down to select another track on the same disc.
An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following r easons: • Excessive vibration • Disc inserted upside down • Damaged disc • W ater condensation on optics Radio Display Messages Y our radio has been designed to display certain messages when a problem is detected with the CD player .
6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3 ⁄ 4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in fr ont of the changer .
Playing Discs The radio will show the CD number , the CD track number , and the T rack T ime Elapsed while the radio is in the CD mode. If more than one CD is loaded in the changer , the changer will automatically play the next disc after playing the last track of the current disc.
Program Button 5 Press this button to play the pr evious disc. Time Button Press this button to switch between time of day and CD track time. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode.
changing tracks or DVD functions, as well as selecting discs loaded in the 6 disc CD/DVD changer while listening to the Rear Audio/V ideo System. Operating Instructions — CD/DVD Changer Loading The CD/DVD Changer The CD/DVD changer is a multi-disc changer , and will accept up to six discs.
4. Repeat the process for loading any additional CD/ DVDs. The CD/DVD changer will stop while additional CD/DVDs are loaded. If the volume control is ON, the unit will switch fr om radio to CD/DVD mode and begin to play .
Operating Instructions — Remote Control Power Button (PWR) Pressing the “POWER” button will turn the r ear audio/ video system ON/OFF . The headphone symbol will flash for approximately 5 seconds in the radio display and sound can be heard fr om the headphones.
SEEK Button • CD/DVD changer Press the right side of the “SEEK” button for the next chapter or track on the disc. Press the left side to r eturn to the beginning of the current chapter or track. Pr ess the left side of the “SEEK” button twice within 2 seconds to return to the pr evious chapter or track.
Operating Instructions — Video Screen Push up on the release button to lower the video scr een. 1. Screen W idth Button Changes the width of the screen pictur e. 2. Enter Button This button will enter the selection from the on-scr een menu. 3. Brightness Button Changes the brightness of the screen pictur e.
Operating Instructions — Headphones 1. ON/OFF Button 2. Scan Button 3. V olume Control 4. LED Power Button Pressing the power button will turn the headphones ON/OFF . NOTE: • The headphones will turn off automatically and the red LED will illuminate for appr oximately 2 minutes when the radio or rear audio/video system is turned off.
headphones are on. This button is used only if the headphones are locked on to a sour ce other than the vehicle’s radio. NOTE: When the “GREEN LED” is showing the head- phones are r eceiving the audio signal.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference r eceived, including interference that may cause undesired operation.
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the rear surface of the steering wheel at the 3 and 9 O’clock positions. The right hand rocker switch has a push button in the center and controls the volume and mode of the sound system.
T ape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection.
5. A loose tape should be corr ected before use. T o rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the requir ed directions. Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
other than off, it selects the amount of air deliver ed to the passenger compartment. There ar e four blower speeds. The fan speed increases as you move the control clockwise.
Front Mode Control The mode control allows you to choose from several patterns of air distribution. NOTE: T o improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots.
Bi-Level Mode Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. NOTE: In many temperature lever positions, the bi- level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Mix Mode Air comes from the floor , defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keep- ing the windshield clear . Defrost Mode Air comes from the windshield and side window demist outlets.
Defrost modes ar e selected. This is done to assist in drying the air and it will help in keeping the windows from fogging. Manual Air Conditioning Operation T o turn on the air conditioning, set the front blower control to any position except O (OFF) and press the A/C button which is located next to the recir culation button.
recir culation mode to rapidly cool the inside of the vehicle. The recir culation mode can also be used to temporarily block out outside odors, smoke, and dust. NOTE: • When the ignition switch is turned OFF , the recir cula- tion feature will be cancelled.
• Start the engine, and continue to hold in the “Rear W ipe/W ash” button until the indicator light starts flashing repeatedly . • Press the r ecirculation button until the indicator light remains lit. • The selection will be stored when the ignition switch is turned OFF or if the “Rear W ipe/W ash” button is pressed.
Rear Blower Control The primary control for the r ear blower is on the front climate control unit located on the instr ument panel. The center knob on the front climate contr ol unit has five positions, “REAR”, “OFF”, and a range of blower speeds.
CAUTION! Interior air enters the Manual Rear Zone Climate Control system through an intake grille located in the passenger side trim panel behind the third seat. The heater outlets are located in the passenger side trim panel just behind the sliding door .
Infrared Three-Zone Automatic T emperature Control — If Equipped The Infrared Thr ee-Zone Automatic T emperature Control System automatically maintains the interior comfort level desired by the driver and all passengers.
desired temperatur e is displayed, the system will achieve and maintain that comfort level automatically . When the system is set up for your comfort level, it is not necessary to change the settings. Y ou will experience the greatest efficiency by simply allowing the system to function automatically .
• The “DELA Y” symbol will flash to indicate that the feature as been enabled. Power Button This button turns the entire system ON/OFF . When the system is turned on it will return to the pr evious settings. Manual Operation This system offers a full complement of manual override features.
Bi-Level Mode Air comes from both the instrument panel outlets, floor outlets and defrost. A slight amount of air is also directed through the side window demister outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Mix Mode Air comes from the floor , defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keep- ing the windshield clear . Defrost Mode Air comes from the windshield and side window demist outlets.
Depress the “A/C” button to turn on and of f the air conditioning during manual operation only . Cool dehumidified air comes through the outlets selected by the Mode Control. T o turn off the air condi- tioning, press the A/C button a second time.
Selecting the “AUTO” position for the Rear Automatic T emperature Contr ol System from the front A TC control unit, illuminates a “LOCK” symbol in the rear display . The rear temperatur e and air source are contr olled from the front A TC control unit.
Rear T emperature Contr ol button. Once the desired tem- perature is displayed, the system will achieve and main- tain that comfort level automatically . When the system is set up for your comfort level, it is not necessary to change the settings. Y ou will experience the greatest efficiency by simply allowing the system to function automatically .
CAUTION! Interior air enters the Rear Automatic T emperature Control System through an intake grille located in the passenger side trim panel behind the third seat. The heater outlets are located in the passenger side trim panel just behind the sliding door .
Bi-Level Mode Air comes from both the headliner outlets and the floor outlets. NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the head- liner outlets and warmer air from the floor outlets. Headliner Mode Air comes from the outlets in the headliner .
W indow Fogging V ehicle windows tend to fog on the inside in mild rainy or humid weather . T o clear the windows, use the A/C, P ANEL and blower controls. Direct the panel outlets toward the side windows. Do not use the Recir culation mode without A/C for long periods as fogging may occur .
A/C Air Filter — If Equipped The climate control system filters out dust, pollen and some odors from the air . Strong odors can not be totally filtered out.
Rear Wiper Operation — Automatic T emperature Control Only Press this button to have the r ear wiper have a continuous wipe. When the ignition switch is in the ON/RUN position, the rear wiper switch position as well as an indicator light will show that the wiper is ON.
NOTE: The washers will stop spraying if the switch is pressed longer than 10 seconds. Adding W asher Fluid The fluid reservoir for the windshield washers and the rear window washer is shar ed. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
Electric Rear Window Defroster — If Equipped Press this button to turn on the r ear window defroster and the optional heated mirr ors. A light will show that the defroster is on. The defr oster automati- cally turns off after about 10 minutes of operation.
.
ST ARTING AND OPERA TING CONTENTS m Starting Procedur es ..................... 2 3 8 ▫ Normal Starting ...................... 2 3 8 ▫ Extremely Cold W eather (Below 2 2 9 °CO r 2 2 0 ° F ) ............... 2 3 8 ▫ If Engine Fails T o Start ....
m T ire Safety Information ................... 2 5 2 ▫ T ire Markings ........................ 2 5 2 ▫ T ire Identification Number (TIN) .......... 2 5 5 ▫ T ire Loading And T ire Pressur e ........... 2 5 6 m T ires—General Information ......
m T ire Rotation Recommendations ............ 2 7 3 m Fuel Requirements ...................... 2 7 4 ▫ Reformulated Gasoline ................. 2 7 5 ▫ Gasoline/Oxygenate Blends .............. 2 7 5 ▫ MMT In Gasoline ..................... 2 7 6 ▫ Sulfur In Gasoline .
ST ARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle.
W ARNING! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- mission cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
CAUTION! T o prevent damage to the starter , do not crank the engine for more than 15 seconds at a time. W ait 10 to 15 seconds before trying again. If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released.
AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Automatic T ransmission Ignition Interlock System This system prevents the key fr om being removed unless the shift lever is in P ARK. It also prevents shifting out of P ARK unless the key is in the OFF or ON positions.
possible convenience. Y our dealer has diagnostic equip- ment to determine if the problem could r ecur . If the transmission cannot be reset, dealer service is requir ed. Gear Ranges DO NOT race the engine when shifting from P ARK or NEUTRAL positions into another gear range.
• “3” Drive This range eliminates shifts into Overdrive. The transmis- sion will operate normally in First, Second and Third while in this range. The “3” position should also be used when descending steep grades to prevent brake system distress.
CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling. P ARKING BRAKE When the parking brake is applied with the ignition switch on, the brake light in the instrument cluster will turn on.
added precaution, turn the fr ont wheels toward the curb on a downhill grade and away from the curb on a uphill grade. The parking brake should always be applied when the driver is not in the vehicle. W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
by increased pedal travel during application, gr eater pedal force r equired to slow or stop, and potential activation of the Brake W arning Lamp. Anti-Lock Brake System — If Equipped The Anti-Lock Brake System pr ovides increased vehicle stability and brake performance under most braking conditions.
When the vehicle is driven over approximately 15 mph (25 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises ar e the system performing its self check cycle to ensure that the ABS system is working properly .
W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
W ARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
• There is a T raction Contr ol System malfunction • The system has been deactivated to prevent damage to the brake system due to overheated brake tempera- tures NOTE: The T raction Control will make buzzing or clicking sounds when in operation.
TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ( ....blank.... ( = Passenger car tire based on European design standards L T = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and T ire Pressure T ire Placard Location NOTE: Some vehicles have a “T ire and Loading Infor- mation” placard located on the driver’s side “B” pillar .
Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loadi.
5. Determine the combined weight of luggage and car go being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle.
ST ARTING AND OPERA TING 259 5.
W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Underinflation also increases tire rolling r esistance and results in higher fuel consumption.
The pressur e should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pr essure. Do not make a visual judgement when determining proper inflation.
T ire pressur e may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pr essure build up or your tire pr essure will be too low . T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits.
Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed.
T read Wear Indicators T read wear indicators ar e in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tr ead grooves and will appear as bands when the tr ead depth becomes 1/16 inch (2 mm).
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, result- ing in changes to steering, handling, and braking of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a result of tire and wheel out-of- balance. Proper balancing will r educe vibration and avoid tire cupping and spotty wear . ALL WHEEL DRIVE (A WD) — IF EQUIPPED CAUTION! All Wheel Drive (A WD) vehicles must have the same size and type tires on all wheel positions.
are significantly underinflated. It is particularly impor - tant, therefor e, for you to check the tire pressur e in all of your tires r egularly and maintain proper pressur e. 1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pr essure levels of 28 psi [1.9 bars] (193 kPa) or less detected in one or more tir es.
TIRE PRESSURE NOW A V AILABLE The TPM system is functioning normally and the external interference is no longer af fecting the system. SP ARE TIRE IN USE? YES/NO The TPM system requir es more informat.
CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor dam- age may result when using replacement equipment that is not of the same size, type, and/or style.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed op- eration.
NOTE: In order to avoid damage to tir es, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufactur er’s instructions on method of installation, operating speed, and conditions for usage.
Section of this manual. More fr equent rotation is permis- sible if desired. The r easons for any rapid or unusual wear should be corrected prior to r otation being per- formed. NOTE: The T ire Pressur e Monitor system must be retrained following a tir e rotation.
Poor quality gasoline can cause problems such as har d starting, stalling and hesitations. If you experience these symptoms, try another brand of “regular” gasoline be- fore considering service for the vehicle.
CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system com- ponents. Problems that r esult from using methanol/gasoline blends are not the r esponsibility of the manufacturer and may not be covered by the vehicle warranty .
Sulfur In Gasoline Y our vehicle may have been designed to meet California low emission standards when using cleaner burning California reformulated gasoline with low sulfur .
Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law . Using leaded gasoline can impair engine performance, damage the emission control system, and could r esult in loss of warranty coverage.
• Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed ar ea, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. NOTE: The driver’s side sliding door cannot be opened while the fuel door is open.
W ARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury . • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increase while you drive.
• V ehicle Identification Number (VIN) • T ype of V ehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the V ehicle Identification Number (VIN). Gross V ehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.
Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR. Loading T o load your vehicle properly , first figure out its empty weight, axle by axle and side by side.
TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer car efully re- view this information to tow your load as efficiently and safely as possible.
NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor - mance and extend transaxle life by reducing excessive shifting and heat build up. W ARNING! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail.
TRA VEL CONDI- TION MAXIMUM TRAILER WEIGHT (TRAILER FRONT AL AREA NOT TO EXCEED 32 SQ. FT .) 3.3L,& 3.8L EN- GINES WITH 4-SPEED AUTO- MA TIC TRANS- AXLE 3.3L & 3.8L EN- GINES WITH HEA VY DUTY TRAILER TOW P ACKAGE 3.8L ENGINES WITH 4-SPEED AU- TOMA TIC TRANS- AXLE 3.
A load equalizing hitch is recommended for loaded trailer weights above 1,000 lbs (454 kg) and requir ed for weights above 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity .
.
WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Flasher .................. 2 9 0 m If Y our Engine Overheats ................. 2 9 1 m Jacking And T ire Changing ................ 2 9 2 ▫ Jack Location ........................ 2 9 3 ▫ Spare T ire Stowage .
HAZARD W ARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the radio. T o engage the Hazard W arning Flashers, depress the switch on the instrument panel. When the Hazar d W arn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traf fic of an emer- gency .
IF YOUR ENGINE OVERHEA TS In any of the following situations, you can reduce the potential for overheating by taking the appr opriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual.
Jack Location The jack and jack-handle are stowed behind the r ear left side trim panel in the cargo ar ea. Pull up on the lever to release the cover . Spare Tire Stowage The spare tir e is stowed under the rear of the vehicle by means of a cable winch mechanism.
Spare T ire Removal Fit the jack-handle over the drive nut. Rotate the nut to the left until the spare is on the gr ound with enough slack cable to allow you to pull the tire out fr om under the vehicle. CAUTION! The winch mechanism is designed for use with the jack handle only .
• T urn on the Hazard W arning Flasher . • Block both the front and r ear of the wheel diagonally oppo- site the jacking position. For example, if changing the right front tir e, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
properly engaged in the described location. Do not raise the vehicle until you are sure the jack is securely engaged. 5. Raise the vehicle by turning the jack scr ew to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tir e.
nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wr ench by your dealer or at a service station. 10. Lower the jack to its fully closed position.
JUMP-ST ARTING PROCEDURES IF BA TTER Y IS LOW W ARNING! T ake care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. Y ou can be hurt by the fan. W ARNING! • Do not attempt to push or tow your vehicle to get it started.
1. W ear eye protection and r emove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boost is pr ovided by a battery in another vehicle, park that vehicle within booster cable reach and without letting the vehicles touch.
W ARNING! Rapid acceleration on slippery surfaces is danger- ous. Unequal traction can cause sudden pulling of the front wheels. Y ou could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow , wet mud, loose sand, etc.
W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck.
CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flat bed truck.
TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A T OW DOLLEY The manufacture does not recommend that you tow an All-Wheel Drive (A WD) or front wheel drive vehicle on a tow dolley .
.
MAINT AINING YOUR VEHICLE CONTENTS m 3.3L/3.8L Engines ...................... 3 0 8 m Onboard Diagnostic System — OBD II ........ 3 0 9 m Emissions Inspection And Maintenance Programs ............................ 3 1 0 m Replacement Parts ..........
▫ Steering Shaft Seal .................... 3 2 3 ▫ Steering Linkage ...................... 3 2 3 ▫ Drive Shaft Universal Joints .............. 3 2 3 ▫ Body Lubrication ..................... 3 2 4 ▫ W indshield W iper Blades ................ 3 2 4 ▫ W indshield And Rear W indow W ashers .
▫ Front Fog Light ...................... 3 4 9 ▫ Rear T ail, Stop, T urn Signal, Side Marker And Back-Up Lights ....................... 3 5 0 ▫ Center High Mounted Stop Light (CHMSL) . . . 351 ▫ License Light ........................ 3 5 1 m Fluid Capacities .
3.3L/3.8L ENGINES 308 MAINT AINING YOUR VEHICLE.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle’s emissions control system.
ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
Engine Oil Checking Oil Level T o assure pr oper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures ar e below 32°F (0°C). • Stop and Go driving. • Extensive engine idling.
American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only r ecommends API Certified engine oils that meet the requir ements of DaimlerChrysler Material Stan- dard MS-6395.
Synthetic Engine Oils There ar e a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that meet the Ameri- can Petroleum Institute (API) and SAE viscosity stan- dard. Follow the service schedule that describes your driving type.
Belts should be inspected for evidence of cuts, cracks, or glazing, and replaced if ther e is indication of damage which could result in belt failur e. If adjustment is re- quired, see your authorized dealer for service. Low generator belt tension can cause battery failure.
Engine Fuel Filter A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause hard starting. Should an excessive amount of dirt accumulate in the fuel tank, filter replacement may be necessary . Catalytic Converter The catalytic converter requir es the use of unleaded fuel only .
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
W ARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water .
Air Conditioner For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time.
Refrigerant Recovery And Recycling The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The manufactur er recommends that air conditioning service be done by facilities using refrigerant r ecycling and recovery equipment that meets SAE standard J1991.
If necessary , add fluid to restore to the pr oper indicated level. W ith a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. Front Suspension Ball Joints The front suspension ball joints ar e permanently sealed.
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate, sliding doors and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against r ust and wear .
washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water . The washer fluid reservoir will hold a full gallon of fluid when the Low W asher Fluid Light illuminates.
W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
Coolant Checks Coolant protection checks should be made every 12 months (prior to the onset of freezing weather , where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fr esh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
CAUTION! Mixing of coolants other than specified (non- HOA T), may result in engine damage that may not be covered under the new vehicle warranty , and decreased corrosion protection. If a non-HOA T cool- ant is introduced into the cooling system in an emergency , it should be replaced with the specified coolant as soon as possible.
Coolant Pressure Cap The coolant pressur e cap must be fully tightened to prevent loss of coolant, and to insur e that coolant will return to the radiator fr om the coolant recovery bottle. The coolant pressur e cap should be inspected and cleaned if there is any accumulation of for eign material on the sealing surfaces.
operating temperature is satisfactory , the coolant recov- ery bottle need only be checked once a month. When additional coolant is needed to maintain the proper level, it should be added to the coolant r ecovery bottle.
• Do not change the thermostat for summer or winter operation. If replacement is ever necessary , install ONL Y the corr ect type thermostat. Other designs may result in unsatisfactory cooling performance.
W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou wouldn’t have your full braking capacity in an emergency .
replaced immediately! Eventual deterioration of the hose can take place resulting in a possibility of a burst failur e. W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately .
W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter or moisture.
Automatic T ransmission The automatic transmission and differ ential assembly are contained within a single housing. All automatic transmissions are equipped with a conven- tional filler tube and dipstick. If fluid is added, it should be added through the dipstick hole in the case.
Procedure For Checking Fluid Level The fluid level in the automatic transmission should be checked whenever the vehicle is serviced. Operation with an improper fluid level will gr eatly reduce the life of the transmission and of the fluid. T o properly check the automatic transmission fluid level, the following procedur e must be used: 1.
CAUTION! Do not overfill. Dirt and water in the transmission can cause serious damage. T o prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is reseated properly .
Power T ransfer Unit The fluid should be maintained at the bottom of the filler hole opening. If it becomes necessary to add or replace the fluid, use only the manufacturers r ecommended fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
Severe Usage is defined as: 1. Mor e than 50% of vehicle operation in stop and go traffic wher e the vehicle is driven regularly for more than 45 minutes of continuous operation, such as in heavy city or in construction zone traf fic, 2.
• Insects, tree sap and tar . • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. W ashing • W ash your vehicle regularly . Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water .
• If your vehicle is damaged due to an accident or similar cause which destroys the paint and pr otective coating have your vehicle repair ed as soon as possible.
and Mopar T otal Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery . Application of a leather conditioner is not requir ed to maintain the original condition.
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water . Do not remove the belts fr om the car to wash them.
dip it back into the water about six times. This will loosen any remaining debris. Rinse the drawer thor oughly un- der warm running water . Shake the excess water from the drawer and dry the outer surfaces with a clean soft cloth. Let the drawer sit in a dish drainer overnight to allow the inside mechanism to dry .
CAUTION! • When installing the Integrated Power Module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Center & Rear Dome Light .
BULB REPLACEMENT Headlights 1. Remove the thr ee screws securing the headlight mod- ule. 2. T urn the bulb socket retaining ring counter clockwise. 3. Disconnect the electrical connector and r eplace the bulb.
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. Front Park/T urn Signal and Sidemarker Lights 1. Remove the thr ee screws securing the headlight mod- ule.
2. T wist the turn signal socket to remove fr om the headlight module and pull bulb from socket. 3. Replace bulb, reinstall socket and then reinstall the headlight module. Front Fog Light 1. Reach behind the fr ont fascia from under the vehicle. 2. T wist the front fog light bulb to r emove from the fog light module.
Rear T ail, Stop, T urn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two light assembly push-in type fasteners. 3. Squeeze the socket assembly tabs to r emove it from the housing. 4. Pull the bulb to r emove it from the socket.
Center High Mounted Stop Light (CHMSL) 1. Remove the two scr ews securing the CHMSL. 2. T wist the bulb socket to remove fr om the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, r einstall the socket and reattach the CHMSL. License Light 1.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil Use API Certified, meeting material standard MS-6395, (GF-3).
Chassis Component Fluids, Lubricants and Genuine Parts. Automatic T ransmission Mopar t A TF+4 Automatic T ransmission Fluid. A WD Power T ransfer Unit Mopar t Gear Lubricant 75W -90. A WD Overrunning Clutch Mopar t A TF+4 Automatic T ransmission Fluid.
.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance ........ 3 5 6 m Maintenance Schedules ................... 3 5 6 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system.
• T axi, police, or delivery service (commercial ser - vice). L • Off-r oad or desert operation. NOTE: Most vehicles are operated under the conditions listed for Schedule 9 B 9 . Second is Schedule “A” . It is for vehicles that are not operated under any of the conditions listed under Sched- ule 9 B 9 .
At Each Oil Change • Change the engine oil filter . • Inspect the exhaust system. • Inspect the brake hoses. • Inspect the CV joints and front suspension compo- nents. • Check the automatic transmission fluid level. • Check the coolant level, hoses, and clamps.
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L .
Miles 3, 000 6, 000 9, 000 12, 000 15, 000 18, 000 (Kilometers) (5 000 ) (10 000 ) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 21, 000 24, 000 27, 000 30, 000 33, 000 36, 000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 39, 000 42, 000 45, 000 48, 000 51, 000 54, 000 (Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 57, 000 60, 000 63, 000 66, 000 69, 000 72, 000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (110 000) (1 15 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if neces- sary .
Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter . XXXXX X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change the All Wheel Drive power transfer unit fluid. (See the note at the end of this chart.) XX Change the All Wheel Drive (A WD) overrun- ning clutch and rear carrier fluid.
Miles 93, 000 96, 000 99, 000 100, 000 102, 000 105, 000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000) Change engine oil and engine oil filter . X X X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary .
Miles 108, 000 1 1 1, 000 1 14, 000 1 17, 000 120, 000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) Change engine oil and engine oil filter . XXXX X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if neces- sary .
Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. NOTE: The A WD power transfer unit fluid and the A WD overrunning clutch/ r ear c.
SCHEDULE “A” Miles 6, 000 12, 000 18, 000 24, 000 30, 000 36, 000 (Kilometers) (10 000) (19 000) (29 000) (38 000 ) (48 000) (58 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Inspect the brake linings.
Miles 42, 000 48, 000 54, 000 60, 000 66, 000 72, 000 (Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) (1 15 000) [Months] [42] [48] [54] [60] [66] [72] Change engine oil and engine oil filter . X X XXXX Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 78, 000 84, 000 90, 000 96, 000 100, 000 (Kilometers) (125 000) (134 000) (144 000) (154 000) (160 000) [Months] [78] [84] [90] [96] Change engine oil and engine oil filter . X X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary .
Miles 102, 000 108, 000 114, 000 120, 000 (Kilometers) (163 000) (173 000) (182 000) (192 000) [Months] [102] [108] [1 14] [120] Change engine oil and engine oil filter . X X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary .
Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .......................... 3 7 6 ▫ Prepar e For The Appointment ............ 3 7 6 ▫ Prepar e A List ........................ 3 7 6 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
The manufacturer has empower ed its dealers to make warranty and repair decisions that ensur e you are not inconvenienced. There is no need for you to wait for a decision from the manufactur er .
In Mexico contact: A v . Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P . 05109 Mexico, D. F . In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assi.
Contract, and you requir e service after your manufactur- er’s new vehicle limited warranty expires, please r efer to your contract documents, and contact the person listed in those documents. W e appreciate that you have made a major investment when you purchased your new vehicle.
REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway T raffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer .
• Service Manuals. These comprehensive service manuals pr ovide the information that students and professional technicians need in diagnosing/troubleshooting, pr oblem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles.
DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway T raffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car .
T emperature Grades The temperature grades ar e A (highest), B, and C, repre- senting the tire’s r esistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
.
INDEX 10.
Adding Fuel ........................... 2 7 9 Adding W asher Fluid .................. 232,324 Additives, Fuel ......................... 2 7 7 Adjustable Pedals ........................ 1 1 6 Air Conditioner Maintenance ............... 3 2 1 Air Conditioning .
Filter ............................... 3 3 7 Fluid and Filter Changes ................. 3 3 7 Fluid Level Check ...................... 3 3 6 Interlock System ....................... 2 4 2 Reset Mode .......................... 2 4 2 Selection Of Lubricant .
Cargo Compartment Luggage Carrier ....................... 1 4 9 Cassette T ape and Player Maintenance ......... 2 0 7 Cassette T ape Player ..................... 1 7 1 Catalytic Converter ...................... 3 1 8 CD Changer ...................... 179,192,197 CD Player .
Radiator Cap ......................... 3 2 9 Selection of Coolant .................. 327,352 Cruise Contr ol .......................... 1 1 7 Cruise Light ........................... 1 6 7 Cup Holder ......................... 140,343 Customer Assistance .
Air Cleaner Filter ...................... 3 1 7 Block Heater ......................... 2 4 0 Break-In Recommendations ................ 7 2 Checking Oil Level ..................... 3 1 3 Compartment ......................... 3 0 8 Coolant .............
Fuel ................................. 2 7 4 Adding ............................. 2 7 9 Additives ............................ 2 7 7 Clean Air ............................ 2 7 5 Filler Cap ............................ 2 7 9 Filter ....................
High Beam/Low Beam Select Switch ........ 1 1 1 Lights On Reminder .................... 1 0 9 Replacing ............................ 3 4 7 T ime Delay .......................... 1 0 9 Heated Seats ............................ 8 8 Heater ..............
Key-In Reminder ......................... 1 3 Keyless Entry System ...................... 2 0 Keys ................................. 1 2 Knee Bolster .......................... 54,55 Lap/Shoulder Belts ....................... 4 0 LA TCH (Lower Anchors and T ether for CHildren) .
Malfunction Indicator ................... 1 6 5 Oil Pressur e .......................... 1 6 5 Park ............................. 107,348 Passing ............................. 1 1 1 Reading ............................. 1 2 0 Rear Servicing ..........
Mini-T rip Computer ...................... 1 2 4 Mirrors ................................ 8 1 Automatic Dimming ..................... 8 2 Electric Remote ........................ 8 4 Exterior Folding ........................ 8 2 Heated ...............
Overheating, Engine ................... 164,291 Owner’s Manual ....................... 4,380 Panic Alarm ............................ 2 2 Parking Brake .......................... 2 4 5 Parking On Hill ......................... 2 4 5 Passing Light ..
Rear Seat Removal ...................... 93,95 Rear Seating Flexibility .................. 97,99 Rear W indow Defroster ................... 2 3 3 Rear W indow Features .................... 2 3 0 Rear W iper/W asher ................... 230,231 Rearview Mirrors .
Untwisting Procedur e .................... 4 6 Seats ................................. 8 5 Adjustment ........................... 8 5 Bench ............................. 95,96 Easy Entry ............................ 9 0 Easy-Out Roller ...............
Linkage ............................. 3 2 3 Power ........................... 249,322 Shaft Seal ............................ 3 2 3 T ilt Column .......................... 1 1 4 Steering Wheel Mounted Sound System Controls ............................
Radial .............................. 2 6 4 Replacement ....................... 266,268 Rotation ............................. 2 7 3 Safety ........................... 252,260 Sizes ............................... 2 5 3 Snow T ires ...................
V anity Mirrors ........................... 8 4 V ariance, Compass ....................... 1 2 2 V ehicle Certification Label ................. 2 8 1 V ehicle Identification Number ................ 6 V ehicle Information Center ................. 1 2 5 V ehicle Loading .
Ein wichtiger Punkt beim Kauf des Geräts Chrysler 2004 Town and Country (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Chrysler 2004 Town and Country noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Chrysler 2004 Town and Country - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Chrysler 2004 Town and Country reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Chrysler 2004 Town and Country erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Chrysler 2004 Town and Country besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Chrysler 2004 Town and Country verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Chrysler 2004 Town and Country. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Chrysler 2004 Town and Country gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
