Benutzeranleitung / Produktwartung SMART MOVE PM-1634AB 6/01 des Produzenten Century
Zur Seite of 28
Instruction Manual A void injury or death - Read and understand this manual! Para instrucciones en Español, llamar al: 1-800-837-4044 www .centuryproducts.
T ABLE OF CONTENTS Important Information..................................... 1 W arnings......................................................... 2 Basic Information............................................ . 4 V ehicle Seat Belts.................
IMPORT ANT INFORMA TION No car seat can guarantee protection fr om injury in ever y situation, but pr oper use helps reduce the risk of serious injury or death. Child restraints (car seats) could be recalled for safety reasons. Y ou must register this restraint to be reached in a recall.
W ARNINGS - Prevent serious injur y or death: DO NOT use rear-facing child restraint in a vehicle seating position equipped with an air bag. Child’ s head and neck may be seriously injured when an inflating air bag hits back of child restraint. Never put a car seat in a front vehicle seat unless recommended by vehicle owner’ s manual.
3 DO NOT use car seat if it is damaged or has missing parts. DO NOT use accessories or parts other than those provided by Century or Graco. Their use could alter the performance of the car seat. Rear-facing car seat must be properly leveled: • T oo reclined can result in injury or ejection.
BASIC INFORMA TION This car seat meets or exceeds all applicable requirements of Federal Motor V ehicle Safety Standard 213 for use in motor vehicles and aircraft. Always secure car seat with a vehicle seat belt, even when unoccupied. An unsecured car seat can injure passengers.
Forward-facing HEIGHT & WEIGHT LIMITS A preterm infant or low birth weight infant may be at special risk in a vehicle or aircraft. According to the American Academy of Pediatrics, these infants may suffer breathing difficulties if improperly reclined in a car seat.
When using car seat rear-facing , car seat MUST be able to rotate freely from a reclined to an upright position on impact. • T est by moving car seat through all seating angles. Adjust car seat to reclined or semi-reclined position and place rear-facing on vehicle seat.
(fig. b) (fig. d) (fig. e) Openings T owels REAR-F ACING INST ALLA TION (continued) 7 (fig. c) (fig. a).
Adjust car seat to upright or semi-upright position and place forward-facing on vehicle seat. Thread vehicle seat belt through openings and behind harness straps (fig. a) . Buckle belt. Press down firmly in center of car seat to compress vehicle seat cushion while tightening vehicle seat belt.
(fig. a) (fig. b) (fig. c) (fig. d) (B) (A) Pull to tighten 9 FORW ARD-F ACING INST ALLA TION (continued) Openings.
Place child in car seat with child’ s back flat against back of car seat. Place harness straps over child’ s shoulders and insert tongues into buckle. Pull up on tongues to be sure they are locked. Close harness tie: Position harness tie at arm pit level.
11 2 3 (fig. a) (fig. b) PLACING CHILD IN CAR SEA T (continued) 4.
OPERA TIONS and ADJUSTMENTS Recline / Upright Positions: Rear-facing - MUST use Reclined (#1) or Semi-reclined (#2) position. Forward-facing - MUST use Semi-upright (#3) or Upright (#4) position. • Squeeze lever located under front (fig. b) or rear (fig.
13 (fig. a) (fig. b) 1 2 3 Upper Lower (fig. c) 4 OPERA TIONS and ADJUSTMENTS (continued).
14 Changing Harness Strap Slots: A Loosen harness straps: Pull and hold upper belt tab. Pull harness straps out. B Remove both harness strap loops from Splitter Plate on back of car seat. C Change harness strap slots. Make sure harness straps are threaded through matching slot of seat pad and car seat.
15 Bottom Loop Splitter Plate To p Loop OPERA TIONS and ADJUSTMENTS (continued) (fig. f) Rear Recline Lever (fig. e).
16 VEHICLE SEA T BEL TS T o provide the most secure installation of the car seat: • Read the vehicle owner’ s manual regarding car seat installation and seat belt use with car seat. • Follow all instruction labels on vehicle seat belt and car seat.
17 V ehicle seat belts located for ward of seat crease may not securely hold car seat. Check vehicle owner’ s manual or see vehicle dealer for car seat installation requirements. • If approved for use with car seat, install car seat and check for secure installation by pulling car seat front to back.
18 Lap belts with retractors may or may not hold a car seat securely . Follow these steps to determine if you have a retractor system that will hold car seat securely: a. Pull belt all the way out. b. Allow belt to retract about 6 inches (15 cm). c. Pull out on belt again.
19 DO NOT use with any car seat. ❃ Passive Restraint - Lap Belt with Motorized Shoulder Belt DO NOT use with any car seat. Belts will not stay tight while driving.
20 Pull on latch plate (fig. a) . If belt slides freely through latch plate, a locking clip MUST be used (see Locking Clip section). Some combination lap/shoulder belts with sliding latch plates may be converted into an “automatic locking mode” that will allow use without a locking clip.
21 1/2 inch (1 cm) (fig. a) VEHICLE SEA T BEL TS (continued) A void serious injury or death: • Failure to use locking clip where required will result in car seat not being securely held in place. • Remove locking clip from seat belts when not being used with car seat.
ADDITIONAL INFORMA TION 22 V ehicle may already be equipped with a tether anchor (top strap anchor). See vehicle owner’ s manual for location. If vehicle does not have a tether anchor , one must be installed: • Contact vehicle dealership for proper anchor location and installation.
23 ADDITIONAL INFORMA TION (continued) DO NOT anchor tether strap to the vehicle when using car seat rear-facing . T ether hook must be attached to car seat for rear-facing use. For storage of tether hook: • Attach tether hook to back of car seat using one of the locations shown.
Removing Seat Pad: Remove both harness strap loops from Splitter Plate on back of car seat. Pull harness straps out of harness slots. Remove from harness tie from harness straps. Remove tongues and from harness straps. Unhook “J” hooks from car seat shell.
25 ADDITIONAL INFORMA TION (continued) Seat Pad: Machine-wash separately on gentle cycle and drip dry . Harness Straps: Surface wash only with mild soap and damp cloth. If harness straps are frayed or heavily soiled, they MUST be replaced. Shell: W ipe with mild solution of soap and water .
Store instruction manual behind these tabs. Store Locking Clip on bottom of car seat. Fold instruction manual. 1 If a part is damaged, missing, or you need help or replacement parts, DO NOT return car seat to the store. CALL US FIRST Call toll-free 1-800-837-4044 from anywhere in the U.
Ein wichtiger Punkt beim Kauf des Geräts Century SMART MOVE PM-1634AB 6/01 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Century SMART MOVE PM-1634AB 6/01 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Century SMART MOVE PM-1634AB 6/01 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Century SMART MOVE PM-1634AB 6/01 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Century SMART MOVE PM-1634AB 6/01 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Century SMART MOVE PM-1634AB 6/01 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Century SMART MOVE PM-1634AB 6/01 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Century SMART MOVE PM-1634AB 6/01. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Century SMART MOVE PM-1634AB 6/01 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
