Benutzeranleitung / Produktwartung HVG96 des Produzenten CDA
Zur Seite of 24
Customer Car e Department • T he Group Ltd. • Harb y Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
2 Impor tant This appliance is designed and manufactured solely f or the cooking of domestic (household) food and is not suitable for any non domestic application and therefor e should not be used in a commercial environment. The appliance guarantee will be v oid if the appliance is used within a non domestic environmen t i.
3 Impor tant Safeguards and Rec ommendations – Do not carr y out any cleaning or maintenance without rst disc onnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will become ver y hot. Do not touch hot parts.
4 F eatures and T echnical Data 9 8 5 7 6 2 2 1 4 3 Cooking P oints 1. Auxiliary burner (A) 1,00 kW 2. Semi-rapid burner (SR) 1,75 kW 3. Rapid burner (R) 3,00 kW 4. T riple ring burner ( TR) 3,50 kW Contr ol Panel 5. Auxiliary burner control knob (1) 6.
5 How to U se the Hob Gas Burners Gas ow to the burners is adjusted by turning the knobs (illustrated in g. 2) which contr ol the valves. T urning the knob so that the indicator line points to t.
6 Choice of Burner The symbols printed on the panel by the side of the knob indicate which burner you are c ontrolling. Choose a suitable burner depending on the cookware dia - meter and capacity . The pan diameter should be suitable for the burner pow er to make the most of the burner ’ s high eciency and not waste fuel.
7 Fig . 6a Fig . 6b.
8 Cleaning and Maintenanc e General Tips – Before cleaning the hob switch it o and wait f or it to cool down. – Clean with a cloth, hot water and soap or liquid detergen t. – Do not use products which are abrasive, c orrosive or chlorine based.
9 Burners and Grids – These parts can be removed and cleaned with appropriate pr oducts. – After cleaning, the burners and their ame spreaders must be w ell dried and correctly replaced. – It is very impor tant to check that the burner ame spreader and the cap have been correctly positio - ned.
10 F C Flame failure probe “ T ” Ignitor “ S ” Correct P ositioning of the Auxiliary , S emi-rapid and Rapid Burners – It is very impor tant to check that the burner ame spreader “ F ” and the cap “ C ” have been correctly positioned (see gs.
11 Correct P ositioning of the T riple Ring Burner – The triple ring burner must be correctly positio - ned (see g. 11); the burner ribs must be tted in their housing as shown by the arrow . T he burner correctly positioned must not rotate (g .
12 TIPS FOR INST ALLA TION Location – The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a room or space containing a bath or a show er . – The appliance must not be installed in a bed-sitting room of less than 20m 3 .
13 Installation T echnical Information For The Installer In order to install the cooktop into the kitchen xture, a hole with the dimensions sho wn in g. 10 has to be made, bearing in mind the follo wing: – Within the unit, between the bottom of the c ooktop and the upper surface of a shelf there must be a clearance of at least 30mm.
14 Installing the Separator Below the Base of the Cooktop It is recommended that a 30mm clearance be left between to base of the cooktop and the separat or . The separator shall be heat r esistant, made of low thermal conductivity material and shall be remova - ble with the use of a tool for installation and ser - vice.
15 F astening the C ooktop Each cooktop is provided with an installa tion kit including brackets and screws for fastening the co - oktop to benches from 30 to 40mm thick.
16 Gas Supply Requirements Important Note This appliance is supplied for use on NA TURAL GAS or LPG (check the gas regulation label attached on the appliance). – Appliances supplied for use on NA TURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modication.
17 Gas Connection The installation of the gas appliance to Natur al Gas or LP Gas must be carried out by a suitably quali- ed and registered installer .
18 Gas Connection GB Cat: II 2H3+ The tting (g. 20) is made up of: – 1 nut “ A ” – 1 elbow tting “ C” – gasket “ F ” Connection to the Gas Supply • Be careful when exible pipes are used that they do not come into contact with moving parts.
19 Regulating the Burner Minimum Setting When changing from one type of gas to another , the minimum tap output must also be correct, considering that in this posi - tion the ame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum to the minimum position.
20 Lubrication of the Gas T aps The operations must be ex ecuted by a qualied technician. IMPORT ANT: All intervention regarding installation maintenanc e and conv ersion of the applian- ce must be fullled with original factory par ts. The manufacturer declines any liability resulting fr om the non-compliance of this obligation.
21 Mains Elec tricity Connection Incorrect installation may be dangerous and the manufacturer can not be held responsible. W arning! This appliance must be ear thed The manufac turer declines all responsibility for any problem caused by failure to observe this rule .
22 Appliance Servicing CDA provide a quality and e ective after-sales service to cover all your servicing needs. Please attach your rec eipt to this page for safekeeping . Please help us to help you by ha ving the following inf ormation available when booking a ser vice- call: 1.
23.
T o contact our Customer Care Department, or for Service, please contact us on the details below . 1103995 - ß1 Customer Car e Department • T he Group Ltd. • Harb y Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
Ein wichtiger Punkt beim Kauf des Geräts CDA HVG96 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie CDA HVG96 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für CDA HVG96 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von CDA HVG96 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über CDA HVG96 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon CDA HVG96 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von CDA HVG96 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit CDA HVG96. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei CDA HVG96 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
