Benutzeranleitung / Produktwartung EDD61 des Produzenten CDA
Zur Seite of 20
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
3 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services.
4 • Steam cleaners must not be used when cleaning this appliance. • The performance of your extractor will vary depending on a number of factors. These include: type of extraction, length of ducting, room volume, ventilation available and cleanliness of the filters.
5 Using Y our Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for appro ximately 15 minutes after the end of cooking.
6 T o decrease the speed at any time • T ouch the “-” key a few times, until the required speed is reached. T o switch o the extractor • T ouch the “O ” key : The moving panel will descend to its rest position and the appliance will continue extracting until its height drops below appro x.
7 Energy saving feature This extractor is fitted with an energy saving feature that automatically reduces the motor speed if it is left on the highest setting . When the motor speed is set to the fourth level, it will automatically switch to level three after six minutes of operation.
8 T o remove and replace the grease filters • T ouch the “On/+” key so the moving panel raises to its full extent, then isolate the power supply so it stays raised. • By pulling the two top corners of the front panel (Fig. 2) at the same time, it will be released and pivot toward you.
9 Mounting your Extractor When the extractor is to be installed behind an electric or gas hob, the minimum distance between the hob and extractor must ex ceed 50mm. In the case of a gas hob, the minimum distance from any burner to the back of the hob must also be 65mm.
10 T roubleshooting Y ou observe that Possible Causes What should you do ? The hood does not work. There ia a power outage. Check the power supply . The 9 pin connector is faulty or misconnected. Check the orientation and security of the 9 pin connector .
11 Ducting and V entilation • For best performance and lowest noise output, we recommend the use of 150mm ducting. Use of any smaller ducting will reduce performance and increase noise. • The length of ducting should not ex ceed 5 metres in total.
12 Installation Note • W e recommend that you seek the help of another individual when installing this product. • The fixings supplied are suitable for most installations. It is the responsibility of the installer to ensure that the fixings are suitable for the cabinets in the property .
13 2) Before making a cut-out in the kitchen cabinets or worktop, ensure that there are no structural (or other) obstructions that would hinder installation. Ensure that the cabinet dimensions are sucient to accommodate the extractor , allowing for the specified clearance between the final installed positions of the extractor and the hob.
14 6) L ocate the support frame (trim piece); apply a narrow bead of silicone sealant to the underside of this (Fig. 7). Position this around the cut-out in the worktop (Fig. 8). 7) L ower the main body of the downdraft extractor through the support frame and into its fitted position.
15 9) R efit the motor unit to the main body of the downdraft extractor . This may be positioned with the outlet facing vertically upward or downward.
16 14) Open the filter cover (Figs. 14 & 15) then remove the grease filter package identified in Fig. 15. 15) Position the grease filters as shown in Fig. 16. Downdraft Calibration After installation it is necessary to calibrate the downdraft mechanism.
17 Mains Electricity Connection W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 3Amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse.
18 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELL OW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W .
19 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Units Model Identification edd61 edd91 Annual Energy Consumption AEC Hood 54.
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www. cda.eu www .cda.eu Please contact our Customer Care Department for Service on the details below Customer Care Department The Group L td.
Ein wichtiger Punkt beim Kauf des Geräts CDA EDD61 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie CDA EDD61 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für CDA EDD61 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von CDA EDD61 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über CDA EDD61 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon CDA EDD61 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von CDA EDD61 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit CDA EDD61. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei CDA EDD61 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
