Benutzeranleitung / Produktwartung IT-3100 des Produzenten Casio
Zur Seite of 75
Handheld Printer Terminal User’s Guide Be sure to read “Safety Precautions” inside this guide before trying to use your Handheld Printer Terminal.
• This Product is equipped with the Brycen B-RAPPORE Stack and My W irefree Network Bluetooth User Interface Application, the use of which is gov erned by a license granted by Brycen Co., Ltd. ® • BLUETOO TH is a registered trademark owned by Bluetooth SIG, Inc.
E-1 Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the first time.
E-2 Safety Precautions Wa r ning Dust and Moisture • Though the Handheld Printer T erminal is dust and wa ter splash resistant, its options including the battery pack are not. K eep loose metal objects and containers filled with liquid a way from your Handheld Printer T erminal and the options.
E-3 Caution Printer • Do not touch the areas around the printer motor or head since they can become very hot. Doing so can cause b urns. • T ouching any of the gears while the y are turning with unprotected hands can cause personal injury . Be careful not to come in contact with turning gears.
E-4 Safety Precautions Lithium-ion Battery P ac k Danger • Nev er use the Handheld Printer T erminal and its option including the battery pack and battery next to open flame, near a sto v e, or any other area e xposed to high heat, or leav e them for a long period of time in a vehicle parked in direct sunlight.
E-5 Po wer Supply / A C Adaptor Wa r ning • Do not use the Handheld Printer T erminal at a voltage other than the specified v oltage. Also, do not connect the Handheld Pr inter T erminal to a multi-plug power strip. • Nev er modify , sharply bend, twist, or pull on the po wer cord.
E-6 Safety Precautions Backup Copies of All Important Data Caution • Note that CASIO Computer Co., Ltd. shall not be held liable to you or any third party for any damages or loss caused by deletion .
E-7 Y our Handheld Printer T erminal and its options are precision digital instruments. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation.
E-8 • This guide does not include any information about programming and do wnload procedures. See the applicable separate documentation for information about the procedures.
E-9 GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
E-10 L ’utilisation de ce dispositif est autorisée seulement aux conditions sui v antes : (1) il ne doit pas produire de brouillage et (2) I’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
E-11 Contents Safety Precautions ......................................................................................... E-1 Operating Precautions ................................................................................... E-7 Important ....
E-12 Using the Bridge Satellite Cradle (HA-B61IO) ........................................... E-49 General Guide ................................................................................................... E-49 Connecting the A C Adaptor and Connecting to a Computer .
E-13 Be sure to perform the following steps before trying to use the Handheld Printer Te r minal for the first time. 1. When unpacking, make sure that everything is included. Open the box and make sure that all the items shown here are included. 2. Charge the battery pack.
E-14 3. Load the battery pack into the Handheld Printer T erminal. 1 Tu rn the battery pack cover lock switch on the side of the Handheld Printer T erminal to the “FREE” position. 2 Open the battery pack cover . 3 Install the battery pack (DT -9723LIC).
E-15 Handheld Printer T erminal System Configuration Options Required A C Adaptor f or Bridge Satellite Cradle / Cradle-type Battery Charger AD-S42120BE Cradle-type Battery Charger HA-B30CHG Bridge Sa.
E-16 Handheld Printer T er minal System Configuration Battery Pac k DT -9723LIC P aper Holder* HA-B93PH Splash Protect Co ver* HA-B92PCV AC Cord f or Eur ope A C-CORD-EU AC Cord for North America A C-CORD-US AC Code for T aiwan A C-CORD-TW AC Code for K orea A C-CORD-KR AC Code for A ustralia A C-CORD-A U * Not av ailable for IT -3100M75E.
E-17 AD-S10095AE AD-S10095A U Screen Protect Co ver* HA-B90DCV Cables DT-887AXA Dsub 9-Pin (Female) RS-232C Cross Cable for Bridge Satellite Cradle DT-888RSC RS-422 Modular Cable for connecting Bridge.
E-18 General Guide 25 3 4 5 6 7 8 9 10 1 2 24 11 12 13 14 15 16 17 18 23 19 20 18 21 22 IT -3100 *T he abov e illustrations show a model with C-MOS Imager and Magnetic Card Reader installed.
E-19 1 SD Memory Card Slot 2P r o g r am Ke y (L) 3 Roll Paper Holder 4 Splash Protect Cover and P aper Cutter 5P o w er K ey 6 Indicator 1 (Left Side) Indicator 2 (Right Side) 7 Speaker 8 Brightness .
E-20 General Guide 15 Battery Pack Cov er Lock Switch 16 Battery Pack Cov er 17 PC Card Slot 18 Hand Strap Hook 19 14-pin Serial Interface Connector 20 Po wer T erminals 21 Neck Strap Hooks 22 Magneti.
E-21 1 Fn Key 2 Numeric Keys 3 (Cursor Key) 4 (Cursor Key) 5- 6. 7C 8B S 9 ENT This key is used to switch the character input mode or make various settings in combination with other keys, or start up a pre-registered application. These ke ys are used to input numbers and letters.
E-22 Replacing the Battery Y our Handheld Printer T erminal uses two types of battery: a battery pack and a memory backup battery . A battery pack (DT -9723LIC) is used for the main battery . A backup battery is housed inside the Handheld Printer T erminal.
E-23 To replace the battery pack 1. Make sure that the Handheld Printer T erminal is turned off. If the po wer is on, press the power k ey to turn it of f. 2. T urn the battery pack co ver lock switch on the side of the Handheld Printer Te rminal to the “FREE” position.
E-24 Important! • When replacing the battery pack, mak e sure y ou do not lea v e the Handheld Printer T erminal without a battery pack for mor e than about 10 minutes. Doing so can cause data in the memory to be deleted. • Never try to use other type of ba ttery than the one that is specif ied for this product.
E-25 A flexible hand strap can be attached to the Handheld Printer T erminal. Hook A Hand Strap Hook B Attach the hand strap follo wing the procedure described belo w . 1. Attach Hook B of the hand strap to the hand strap hook located on the bottom of the Handheld Printer T erminal.
E-26 A neck strap can be attached to the Handheld Printer T erminal to keep it from being dropped while being carried. The stylus holder pro vided can also be attached. Attach the neck strap following the procedure described belo w . Attachment Pr ocedure 1.
E-27 Remo val Pr ocedure 1. Pull back the locking bar of the neck strap mounting hook and then release the hook from each ring as sho wn in the illustration.
E-28 2. Remove Mounting Hook C. 3. Pass the stylus holder through the strap as shown in the illustration. 4. Fold back the strap after passing through Bracket C, and then fasten in the same wa y it was originally fastened with Bracket A and Bracket B.
E-29 Calibrating T ouc h Screen Alignment Whenev er you feel that touch screen response is poor or that the operations being executed do not match the location you are tapping on the touch screen, perform the following operations to calibrate the alignment of the touch screen.
E-30 Adjusting Displa y Contrast Perform the follo wing steps to adjust display contrast to make display colors more vi vid and easier to see. • Press the “Fn” key and then mak e sure that “F” appears in the lower right corner of the screen.
E-31 The printer can print on roll paper (80 mm or 58 mm wide)* or 80 mm wide formed sheet paper . When printing on formed sheet paper , use the paper holder (HA-B93PH) sold separately . When Using Roll Paper Installing the Roll Paper 1. Check that the po wer is of f.
E-32 Using the Printer 5. Close the roll paper holder, slide the lock knobs on the left and right sides as shown in the illustration to align at the “LOCK” position to lock the roll paper holder in position, and then tear off the protruding roll paper .
E-33 Attaching the 58 mm P aper Width Adjuster Attach the 58 mm Paper W idth Adjuster* inside the roll paper holder when using 58 mm wide roll paper . Refer to the procedure described in “Installing the Roll Paper” for information on opening and closing the roll paper holder .
E-34 Using the Printer When Using Formed Sheet P aper Attaching the Paper Holder Attach the separately sold Paper Holder (HA-B93PH)* w hen printing on formed sheet paper . The Paper Holder is composed of four parts and four scre ws. In addition, a PC card cushion is enclosed to pre vent the PC card from being dislodged by an impact and so forth.
E-35 5. Loosen the two screws shown in the illustration (the scre ws cannot be removed of f). 6. Open the cover (PC card slot cover) as shown in the illustration. 7. Loosen and remove the four screws shown in the illustration. Store the removed screws in a safe place so that they do not become lost.
E-36 Using the Printer 10. Fasten P art A of the Paper Holder to the Handheld Printer T erminal. Press both ends of Part A to fasten to the Handheld Printer T erminal. 11. Insert the projections on both sides of Part into the grooves of Part B and fasten to the Handheld Printer Te rminal with the four screws for the Pa per Holder .
E-37 Loading Formed Sheet Paper Enable the Auto Loading function by selecting Start, Settings, Control Panel and then “Printing Control” of Printer Settings in that order before loading the formed sheet paper . 1. Insert the formed sheet paper all the way into the printer until it stops with the side to be printed facing downward.
E-38 Using the Printer Precautions When Using Printer Printing Accuracy 1. During high-duty printing such as printing horizontal lines or printing while the battery remaining capacity is lo w , the printing speed may slow down to pre vent excess current consumption that may cause unaligned printing f or one dot or more.
E-39 Others 1. The temperature range f or printing with 2-ply paper and label paper is 5 to 35°C. 2. Once the end mark of the paper appears, promptly r eplace with new paper .
E-40 Using the C-MOS Imager (IT -3100M55E/IT -3100M55U/IT -3100M56E/IT -3100M75E only) 1. Turn on the Handheld Printer T erminal, position its C-MOS Imager reader port near the bar code or 2D code, and then press the T rigger Key (R or L). 2. The Handheld Printer T erminal reads the code by emitting laser and red lights.
E-41 • This label is a warning label f or Class 2 laser products that comply with IEC60825-1+A2:2001 CA UTION • Use of controls or adjustments or perf ormance of pr ocedur es other than those specif ied herein may r esult in hazardous radiation exposur e.
E-42 T he Magnetic Card Reader comes as standard with IT -3100 M54E/ M55E/M55U/M 75E. Only use cards that are compatible with the ISO standards. The procedure for reading cards is described below .
E-43 IR Communication IR communication can be used to transfer data between two Handheld Printer Te rminals. When performing IR communication, orient the IR ports of both Handheld Printer T erminals so the y are pointing directly at each other . Data communication is possible within a distance of 0 (in direct contact) to 1 m (max.
E-44 Bluetooth ® Communication Bluetooth ® protocol can also be used to transfer data between two Handheld Printer T erminals. The two Handheld Printer T erminals should be no more than three meters apart (as long as there is nothing blocking the path in between).
E-45 Resetting the Handheld Printer T erminal is the same as restarting a computer . Performing a reset causes all unsaved inputs and edits to be lost, but data that is already stored in the memory as well as all settings should be unaf fected.
E-46 Performing a Full Reset (Initialization) Performing a full reset initializes memory . This means that all data stored in the memory (RAM) is deleted and all the settings are returned to their initial factory settings. Perform a full reset whenever any one of the following conditions exists.
E-47 1. T erminal Model: IT -3100M53E, IT -3100M55E, IT -3100M55U, IT -3100M54E, IT -3100M56E, IT -3100M75E CPU: Marvell ® PXA255 Application Processor (400 MHz max.) Memory: 128MB RAM, 96MB R OM (user def ined: Approx. 30MB) OS: Microsoft ® W indows ® CE 5.
E-48 Character Fonts: Kanji 12-dot 48/32 columns, 16-dot 36/24 columns, 24-dot 24/16 columns (columns shown for 80 mm wide paper and 58 mm wide pa per , respectiv ely) Character Size: Free double-width characters Generating Method : Black/white inv ersion, mixed character font printing 8.
E-49 Back Bottom Right To p F ront The optionally av ailable Bridge Satellite Cradle (HA-B61IO) makes it possible to transfer system data and file data between the Handheld Printer T erminal and a computer using an RS-232C interface or USB interface.
E-50 Using the Bridge Satellite Cradle (HA-B61IO) 1 System Status Indicator Lamp 2 Communication Indicator Lamp 3P ow er Indicator Lamp 4T erminal Detect Switches 5 IR Port 6P ow er Contacts 7P ow er Switch 8A C Adaptor Jack 9 RS-422 Port 10 RS-232C Port 11 USB Port 12 DIP Switches This lamp indicates whether the system is operating normally .
E-51 Connecting the A C Adaptor and Connecting to a Computer Use the AC adaptor a v ailable as an option for the Bridge Satellite Cradle to supply the po wer to it.
E-52 Using the Bridge Satellite Cradle (HA-B61IO) 4. Turn on the po wer . This causes the Bridge Satellite Cradle po wer indicator lamp to light red. 5. Place the Handheld Printer T erminal so that the infrared communication unit on the right side is faced f irmly with the infrared communication unit of the Bridge Satellite Cradle.
E-53 Configuring DIP Switch Settings Removing the bottom co ver of the Bridge Satellite Cradle e xposes the DIP switches. Y ou can change the ON/OFF settings of the DIP switches to set the configuration. Only set the DIP switches after first switching OFF the po wer .
E-54 Using the Bridge Satellite Cradle (HA-B61IO) Connecting Multiple Bridge Satellite Cradles (HA-B61IO) Connect “C-OUT” of the Bridge Satellite Cradle connected to the host computer to “C-IN” of the next Bridge Satellite Cradle you want to connect.
E-55 Model no. of A CAdaptor Area/Region Compliance AD-S42120BE All except China Compliant with CE, UL, FCC, and Energy Ef ficienc y Standards. AD-S42120BE-CN China only Compliant with Energy Ef ficiency Standards and CCC. Bridge Satellite Cradle (HA-B61IO) Specifications 1.
E-56 The optionally av ailable Cradle-type Battery Char ger (HA-B30CHG) lets you charge the Handheld Printer T erminal’ s battery simply by placing the Handheld Printer Te rminal onto the charger .
E-57 1P ow er Indicator Lamp 2T erminal Detect Switches 3P ow er Contacts 4P ow er Switch 5A C Adaptor Jack This lamp indicates the power status and the mounting status of the Handheld Printer T erminal.
E-58 Using the Cradle-type Battery Charger (HA-B30CHG) Connecting the A C Adaptor f or the Cradle-type Battery Char ger Use the dedicated A C adaptor for the Cr adle-type Battery Char ger to connect to a w all outlet.
E-59 Cradle-type Battery Charger (HA-B30CHG) Specifications 1. Charging Charging System: Fix ed-v oltage (with current limiter) Charge T ime: Approximately 8.0 hours 2. Power Supply Power Requirement: A C adaptor (AD-S42120BE*) Power Consumption: 12V DC, approximately 2,100mA Output to Handheld Printer Te r minal : 10V DC 1,800mA (max.
E-60 1. Turn of f the po wer of the Handheld Printer T erminal by pressing the po wer key . 2. Open the jack cover ( ), and then insert the plug of the AC Adapter into the charging jack ( ). After connecting the po wer cable to the AC adaptor , plug the other end of it into an electrical outlet.
E-61 Specifications 1. Charging Specif ication Charging Method: Constant current/voltage Charge Period: Approx. 8 hours (with the power of f) 2. A C Adaptor Model: AD-S10095A Input: 100V to 240V A C 50/60 Hz 0.
E-62 PC card compatible with the PCMCIA(T ype I/II) standard can be installed in the PC Card slot on the Handheld Printer T erminal. Insert a PC card according to the procedure described belo w .
E-63 4. Open the cov er (PC card slot cov er) as sho wn in the illustration. 5. Insert a PC card having PC card remo v al tape attached. Insert the PC card all the wa y in with the top of the card facing tow ards the top of the Handheld Printer Te r minal.
E-64 Using PC Cards Removing a PC Car d Press the eject button on the left side of PC card slot with the stylus as sho wn by the arrow , and pull out the PC card while holding onto the end of the PC card remov al tape. Inserting a PC Card (When Using the P aper Holder) Check the names of the parts of the Paper Holder before be ginning work.
E-65 3. After pushing on both ends of Part A and reattaching to the Handheld Printer Te r minal ( ), remove P art B by removing the scre ws ( ). 4. Insert a PC card to which PC card remov al tape has been attached. Insert the PC card all the way in so that the top of the PC card faces the top of the Handheld Printer T erminal.
E-66 7. While spreading apart both ends of Part A ( ), remov e Part A from the Handheld Printer T erminal by lifting up P art A until the projections reach the upper edges of the grooves of P art B ( ), and then press on Part C and P art D from the left and right sides ( ).
E-67 1 2 SD memory card can be installed in the SD Memory Card slot on the Handheld Printer Te r minal. Insert (or remove) an SD memory card according to the procedure described below . Inserting an SD Memor y Card 1. Check that the power is of f. If the po wer is on, alw ays make sure to turn it of f by pressing the power k ey .
E-68 Connect a bar code reader to the RS-232C interface connector (8-Pin) on the Handheld Printer T erminal. Connecting the bar code reader 1. Check that the power is of f. If the power is on, al ways mak e sure to turn it off by pressing the power k ey .
E-69 Attaching the Screen Protect Cov er to the Handheld Printer T erminal pre vents the screen from being cracked or damaged when carrying. 1. Remov e the two scre ws on the right side of the Handheld Printer T erminal. Store the screws in a safe place after the y ha ve been remov ed.
E-70 Attaching the Splash Protect Cov er to the Handheld Printer T erminal lets you use it ev en during inclement weather . Attach the Splash Protect Cov er by following the pr ocedure described below .
E-71 5. Close the roll paper holder , slide the lock knobs on the left and right sides as sho wn in the illustration to align at the “LOCK” position to lock the roll paper holder in position, and then tear of f the protruding roll paper . • Please note that the positions of the lock knobs on the left and right sides are differ ent.
E-72 Important! • Make sur e to attach the contact cover pr ovided when r emoving the Battery P ack from the Handheld Printer T erminal and storing. • If the battery pack has been left over unused f or a long period of time, the capacity remained decr eases due to spontaneous discharge or chemical decomposition by the battery pack itself.
CASIO COMPUTER CO ., L TD. 6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan.
Ein wichtiger Punkt beim Kauf des Geräts Casio IT-3100 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Casio IT-3100 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Casio IT-3100 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Casio IT-3100 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Casio IT-3100 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Casio IT-3100 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Casio IT-3100 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Casio IT-3100. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Casio IT-3100 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
