Benutzeranleitung / Produktwartung TE2000 des Produzenten Toshiba
Zur Seite of 274
T OSHIBA TE2000 Port a ble Perso n al Computer User’s M a nual.
Copyright © 2001 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein.
EU Declaration of Conformity TOSHIBA declares, that the product: PS600* conforms to the following Standards: Supplementary Inf ormation: “The product complies with the require ments of the Low V oltage Directive 73/23/EEC, the EMC Directive 89/336/EEC a nd/or the R&TTE Directive 1999/05/EEC.
Network Compatibility State ment This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional require- ments conditional in EG 201 121.
Pursua nt to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ❑ The telephone number of the line to whi.
If problems arise If any of your telephone equipment is not operating properly, you should immedi- ately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discon- tinue service.
The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier.
Note s for Users in Australia a nd New Ze ala nd Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compli- ance with Austel standards when the country/region selection is set to Australia.
❑ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within .
❑ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.
Information to Wirele ss LAN User Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any Wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❑ The IEEE 802.
Canada – Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
L’utilisation en extérieur est autorisé sur le canal 10 (2457 MHz) et 11 (2462 MHz). Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, au-dessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m.
USA-Federal Communications Commission(FCC) This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions: ❑ This device may not cause harmful interference. ❑ This device must accept any interference that may cause undesired operation.
❑ Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ❑ Consult the dealer or an experienced radio/TV technician for help.
1. Sticker Please put the following sticker on devices incorporating this product. In the frequency bandwidth of this equipment, industrial device, scientific device, medical device like microwave ove.
3. TOSHIBA Direct PC Monday — Friday : 10:00 — 17:00 Toll Free Tel : 0120-13-1100 Direct Dial : 03-3457-5916 F AX : 03-5444-9450 Electronic communication device authorization This device obtains t.
United States of America and Canada Tested To Comply With FCC Standards FOR HOME OR OFFICE USE. See FCC 47CFR part 15.19(b)(2) This device complies with part15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
T OSHIBA D V D-ROM drive SD-C2502** safety in struction ** means any letters or numbers. CAUTIONS: 1 . The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.
M atsushita CD-R/R W drive UJDA340** safety in struction ** means any letters or numbers. CAUTIONS: 1 . The CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Location of the required label COMPLIES WITH F DA RADIA TION PERFORMANCE ST ANDARDS, 21 CFR SUBCHAPTER J. MANUF ACTURED: Ma nufactured by Kyushu Matsushita Electric Co.
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
Location of the required label COMPLIES WITH F DA RADIA TION PERFORMANCE ST ANDARDS, 21 CFR SUBCHAPTER J. MANUF ACTURED: Ma nufactured by Kyushu Matsushita Electric Co., Ltd. 1-62 4-Chome Minoshi ma, Ha kata-Ku Fukuoka,Ja pa n M atsushita CD-R W/D V D-ROM drive UJDA720** safety in struction ** means any letters or numbers.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
TEAC D V D-ROM drive D V -28E** safety in struction ** means any letters or numbers. This product has been designed and manufactured according to FDA regulations "title 21. CFR. chapter 1, subchapter J. based on the radiation Control for Health and Safety Act of 1968," and is classified as a class 1 laser product.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHO- RIZED service station.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.
Optical pickup Type : PU-2200 Manufacturer : TEAC CORPORATION Laser output : Less than 0.25m W on the objective lens Wavelength : 795nm Location of the required la bel CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.
VORSICHT : Dieses Gerät enthält ein La ser-System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” kla ssifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsa nleitung sorgfältig dur ch und bewa hren diese bitte als Refer enz auf.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIA- TION EXPOSURE.
Location of the required la bel CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHO- RIZED service station.
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
HIT ACHI D V D-ROM drive GD R-8081N** safety in struction ** means any letters or numbers. CAUTIONS: 1 . The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHO- RIZED service station.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä.
xli T a ble of Contents Prefa c e Manual contents ............................................................................... xlvii Conventions ...................................................................................... xlvii Abbreviations .
xlii Slim Select Bay modules ................................................................. 2-11 DVD-ROM drive ............................................................................... 2-12 CD-ROM drive .......................................
xliii Using 3 1/2" external diskette drive ................................................ 4-10 Connecting 3 1/2" diskette drive ....................................................... 4-11 Disconnecting 3 1/2" diskette drive .........
xliv Power indicators ................................................................................ 6-4 Battery indicators ................................................................................ 6-4 DC IN indicator ........................
xlv Addit ional AC ada ptor ........................................................................ 8-9 Battery charger ................................................................................... 8-9 Slim Select Bay HDD adaptor ..............
xlvi Hibernation ....................................................................................... 9-22 Memory expansion ........................................................................... 9-23 LAN .......................................
xlvii Pre f a ce Congratulations on your purchase of the TOSHIBA TE2000 series computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your 2000 computer.
xlviii User's Manual Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password.
xlix Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign ( + ). For example, Ctrl + C means you must hold down Ctrl and at the same time press C .
l User's Manual.
li General Pr e cautio n s Toshiba computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.
User's Manual lii.
1-1 I NTRODUCTION Cha pter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA.
1-2 User's Manual I NTRODUCTION Window s ® XP ❑ The following software is preinstalled: • Microsof t ® Window s ® XP Professional • Modem driver • Display Drivers for Windows • TOSHI.
1-3 I NTRODUCTION • LAN Drivers • Infrared Device Driver • Microsof t ® Internet Explorer6.0 • TOSHIBA Power Saver • TOSHIBA Console • Online manual ❑ Documentation: • Microsof t ® Window s ® 2000 manual package • The same documentation that is supplied with Window s ® XP Professional.
1-4 User's Manual I NTRODUCTION Memory Slots 128 or 256 MB memory modules can be installed in the two memory slots for a maximum of 512 MB system memory. Level 2 cache Provided to maximize performance. • Celeron™ : 128 KB • Pentiu m ® III processor-M : 512 KB Video RAM 16 MB of RAM is provided for video display.
1-5 I NTRODUCTION CD-R/RW drive Some models are equipped with a full-size, CD-R/RW drive module that lets you record CDs as well as run either digital versatile or compact disks without using an adaptor. It runs CDs and CD-Rs at maximum 24 speed and CD- RWs at maximum 14 speed.
1-6 User's Manual I NTRODUCTION AccuPoint II Built-in A pointing device, the AccuPoint II, in the center of the keyboard and control buttons at the base of the keyboard enable control of the on-screen pointer and scrolling of windows . Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack.
1-7 I NTRODUCTION Slots PC card A PC card slot accommodates: Two 5 mm Type II One 10.5 mm Type III Refer to Chapter 8, Optional Device s , for details. Multimedia Sound System Sound Blaster™ Pro™ and Windows Sound System compatible sound system provides internal speaker as well as jacks for an external microphone and headphone.
1-8 User's Manual I NTRODUCTION Slim Select Bay Modules Slim Select Bay is a single-drive bay that accommodates a CD-ROM drive, DVD-ROM drive, CD-R/RW drive, CD- RW/DVD-ROM drive, secondary hard disk drive or secondary battery. The Slim Select Bay utility enables hot docking of modules when you are using a plug and play operating system.
1-9 I NTRODUCTION Sp e c i al f e atur e s The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hotkeys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program.
1-10 User's Manual I NTRODUCTION Auto power on This feature lets you set a time and date for the computer to turn on automatically. The feature is useful for receiving remote communications while you are asleep or away. You can specify the setting in Scheduled Tasks.
1-11 I NTRODUCTION Fn-esse This Windows program lets you define your own “short- cut” keys to quickly launch applications and speed your work in Windows. To start the utility, click the Windows Start button, point to Programs (All Programs in Windows ® XP), point to TOSHIBA Utilities and click Fn-esse.
1-12 User's Manual I NTRODUCTION Easy CD Creator This easy-to-use software lets you record CDs with just a few mouse clicks. You can create CDs in several formats including audio CDs that can be played on a standard stereo CD player and data CDs to store the files and folders on your hard drive.
1-13 I NTRODUCTION Slim Select Bay options The following modules can be installed in the Slim Select Bay. The user can select either a CD-ROM drive, a DVD-ROM drive, a CD-R/CD-RW drive, a CD-RW/ DVD-ROM drive , a Slim Select Bay HDD adaptor or a Slim Select Bay 2nd battery pack to be preinstalled as a standard device.
1-14 User's Manual I NTRODUCTION.
T HE G RAND T OUR 2-1 Ch a pter 2 The Gr a nd T our This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position.
T HE G RAND T OUR 2-2 S ECURITY LOCK SLOT Infrared port This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 Kbps, 57.6 Kbps, 38.4 Kbps, 19.2 Kbps or 9.6 Kbps data transfer with IrDA 1.
T HE G RAND T OUR 2-3 Slim Select Bay A CD-ROM drive, DVD-ROM drive, CD-R/RW drive, CD-RW/DVD-ROM drive, Slim Select Bay HDD adaptor, secondary battery pack can be installed in the Slim Select Bay. A weight saver can be installed when there is no module.
T HE G RAND T OUR User's Manual 2-4 B a ck s ide Figure 2-4 shows the computer’s back side. Figure 2-4 The computer’s back side DC IN 15V The AC adaptor connects to this socket. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer .
T HE G RAND T OUR 2-5 LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). LAN indicator This indicator glows green when the computer is accessing the LAN.
T HE G RAND T OUR User's Manual 2-6 Docking port Use this port to connect an optional Port Replicator. CAUTION: Keep foreign objects out of the docking port. A pin or similar object can damage the computer’s circuitry. Docking holes These holes ensure a proper connection between the computer and an optional Port Replicator.
T HE G RAND T OUR 2-7 Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle.
T HE G RAND T OUR User's Manual 2-8 AccuPoint II A pointer control device located in the center of the keyboard is used to control the on-screen pointer.
T HE G RAND T OUR 2-9 Power source/system indicators DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
T HE G RAND T OUR User's Manual 2-10 The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you enter numbers. When the F11 key indicator glows the keypad overlay lets you control the cursor.
T HE G RAND T OUR 2-11 Slim Select Bay modules Numeric mode You can use the keypad overlay (white labeled keys) for numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboar d . AC a d a ptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer.
T HE G RAND T OUR User's Manual 2-12 D V D-ROM drive An optional full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") digital video disk/compact disk without using an adaptor. It may be selected as a standard component or as an option.
T HE G RAND T OUR 2-13 Slim Select Bay modules DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly.
T HE G RAND T OUR User's Manual 2-14 CD, CD-R read 24 speed (maximum) CD-RW read 14 speed (maximum) CD-R write 8 speed (maximum) CD-RW write 8 speed (maximum) This drive supports the following fo.
T HE G RAND T OUR 2-15 CAUTION: Check the Slim Select Bay indicator when you use the CD- RW/DVD-ROM drive. Do not press the eject button, disconnect a drive or turn off the computer while the light is glowing. Doing so could damage the CD/DVD or the drive.
T HE G RAND T OUR User's Manual 2-16 Slim Select Bay 2nd battery pa ck An optional battery pack can be installed in the Slim Select Bay to increase the computer’s battery power and operating time. For details, refer to the documenta- tion accompanying the secondary battery pack.
3-1 G ETTING S TARTED Cha pter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort.
3-2 User's Manual G ETTING S TARTED Setting up your work spa ce Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
3-3 G ETTING S TARTED ❑ ❑ ❑ ❑ ❑ Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices. ❑ ❑ ❑ ❑ ❑ Allow adequate space behind the computer to let you freely adjust the display.
3-4 User's Manual G ETTING S TARTED Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ ❑ ❑ ❑ ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare.
3-5 G ETTING S TARTED Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. 2. Lift the panel up and adjust it to the best viewing angle for you.
3-6 User's Manual G ETTING S TARTED 1. Connect the power cord to the AC adaptor. Figure 3-3 Connecting the power cord to the AC adaptor 2. Connect the AC adaptor’s DC output plug to the DC IN port on the back side of the computer. Figure 3-4 Connecting the adaptor to the computer 3.
3-7 G ETTING S TARTED T urning on the power This section describes how to turn on the power. NOTE: After you turn on the power for the first time, do not turn it off until you have set up the operating system (OS) and the OS has started up. 1. If the external diskette drive is connected, make sure it is empty.
3-8 User's Manual G ETTING S TARTED Windows XP Profe ssion al/2000 setup When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Professional Startup Screen Logo. Follow the on-screen directions. If you ordered Windows 2000, the operating system is not preinstalled.
3-9 G ETTING S TARTED 2. Make sure all disk activity has stopped, then remove any CDs or diskette. CAUTION: Make sure the Disk, Slim Select Bay and Slim Select Bay’s module indicators are off. If you turn off the power while a disk is being accessed, you can lose data or damage the disk.
3-10 User's Manual G ETTING S TARTED ❑ ❑ ❑ ❑ ❑ You can return to your previous working environment immediately when you turn on the computer. ❑ ❑ ❑ ❑ ❑ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature.
3-11 G ETTING S TARTED 4. Select the Power Save Modes window. 5. Double-click Power Mode (Full Power, Normal, etc.) and open the System Power Mode window. 6. Enable the desired Hibernation settings for When I press the power button and When I close the lid .
3-12 User's Manual G ETTING S TARTED ❑ ❑ ❑ ❑ ❑ Restores the previous working environment more rapidly than does hibernation. ❑ ❑ ❑ ❑ ❑ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature.
3-13 G ETTING S TARTED ❑ ❑ ❑ ❑ ❑ You change certain computer settings. ❑ ❑ ❑ ❑ ❑ An error occurs and the computer does not respond to your keyboard commands. There are three ways to restart the computer system: 1. If you are using Windows XP, click start then click Turn off computer .
3-14 User's Manual G ETTING S TARTED similar to the one below will be shown while the software is being decompressed. Leave it until it disappears. Do not click Cancel . Figure 3-6 Software decompression window 3. Follow the on-screen instructions.
3-15 G ETTING S TARTED.
O PERATING B ASICS 4-1 Cha pter 4 Operating Ba sics This chapter gives information on basic operations including using the AccuPoint II, optical media drives, the external diskette drive, the internal modem, the LAN and changing Slim Select Bay modules.
User's Manual O PERATING B ASICS 4-2 AccuPoint II precaution s Certain conditions can affect the on-screen pointer when using AccuPoint II. For example, the pointer may travel contrary to AccuPoint II operation or an error message may appear, if ❑ You touch the AccuPoint II during power-up.
O PERATING B ASICS 4-3 Cha nging Slim Sele ct Bay module s This section explains how to change modules in the Slim Select Bay. The illustra- tions show replacement of the DVD-ROM drive with the Slim Select Bay HDD adaptor. Therefore, the text refers to those modules.
User's Manual O PERATING B ASICS 4-4 In stalling a module Install the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2. If you want to lock the Slim Select Bay module, set the screw of the Slim Select Bay lock in the back hole.
O PERATING B ASICS 4-5 Using optical media drives CD-R/RW drive Read CD, CD-R 24-speed (maximum) CD-RW 14-speed (maximum) Write CD-R 8-speed (maximum) CD-RW 8-speed (maximum) CD-RW/DVD-ROM drive Read .
User's Manual O PERATING B ASICS 4-6 b. Pressing the eject button will not open the drawer when the computer’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 1.5 cm) such as a straightened paper clip into the eject hole just to the right of the eject button.
O PERATING B ASICS 4-7 Using optical media drives 4. Lay the CD, label side up, in the drawer. NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD tray. Therefore, you will need to turn the CD at an angle when you place it in the tray.
User's Manual O PERATING B ASICS 4-8 6. Push the center of the drawer to close it. Press gently until it locks into place. CAUTION: If the CD is not seated properly when the drawer is closed, the CD might be damaged. Also, the drawer might not open fully when you press the eject button.
O PERATING B ASICS 4-9 Using optical media drives 2. There are indentations on the sides of the drawer to let you grasp the CD. Hold it gently and lift it out. NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD tray.
User's Manual O PERATING B ASICS 4-10 5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVDs. 6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the center out, do not wipe in a circular direction around the CD/ DVD.
O PERATING B ASICS 4-11 Using 3 1/2" external diskette drive NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20 o while it is operating. 2. Do not set anything on top of the diskette drive.
User's Manual O PERATING B ASICS 4-12 Disconnecting 3 1/2" dis kette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped.
O PERATING B ASICS 4-13 Wirele ss communication s Wirele ss LAN The wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with IEEE 802.
User's Manual O PERATING B ASICS 4-14 Wirele ss communication LED The LED indicates the status of the wireless communication functions. LED status Indication LED off Wireless communication switch is set to off. Automatic power down because of overheating.
O PERATING B ASICS 4-15 LAN LAN circuits support Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled.
User's Manual O PERATING B ASICS 4-16 2. Plug one end of the cable into the LAN’s jack. Press gently until you hear the latch click into place. Figure 4-13 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub.
O PERATING B ASICS 4-17 Figure 4-14 The Super Long Life Properties window Network Device Switch This feature lets you select actions that will enable or disable LAN and wireless LAN functions. The following settings can be made in NetworkDeviceSwitch utility.
User's Manual O PERATING B ASICS 4-18 Depending on the settings in the TOSHIBA Power Saver utility, the following four events can trigger a change in the Power Savings settings. To avoid these automatic changes, clear the Control device power management checkbox in the Power Saver utility.
O PERATING B ASICS 4-19 2. The Region Selection icon will appear in the Windows Task Bar. Figure 4-14 The Region Selection icon (Windows ® XP) Figure 4-15 The Region Selection icon (Windows ® 2000) 3. Click the icon with the primary mouse button to display a list of regions that the modem supports.
User's Manual O PERATING B ASICS 4-20 Cleaning the computer Figure 4-17 The menu list (Windows ® 2000) Setting You can enable or disable the following settings: AutoRun Mode Region Select Utility starts automatically when you start up the operating system.
O PERATING B ASICS 4-21 Dialing Properties Select this item to display the dialing properties. CAUTION: If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select Japan region mode.
User's Manual O PERATING B ASICS 4-22 Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer in the same manner.
O PERATING B ASICS 4-23 ❑ Close the display. Do not pick up the computer by its display panel or back (where the interface ports are located). ❑ Close all port covers. ❑ Use the carrying case when transporting the computer. He at dispersal To protect from overheating, the CPU has an internal temperature sensor.
User's Manual O PERATING B ASICS 4-24.
T HE K EYBOARD 5-1 Cha pter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer.
User's Manual T HE K EYBOARD 5-2 F1 … F12 function keys The function keys, not to be confused with Fn , are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed.
T HE K EYBOARD 5-3 Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter , Ctrl and Alt keys to the right of the main keyboard.
User's Manual T HE K EYBOARD 5-4 Hotkeys Hotkeys ( Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hotkeys, the current setting will be displayed as an icon.
T HE K EYBOARD 5-5 Hibernation: Press Fn + F4 to turn Hibernation mode on and off. When you press these hotkeys, the current setting will be displayed in a dialog box that will let you OK or cancel the displayed setting. A check box lets you select whether to hide or display the dialog box.
User's Manual T HE K EYBOARD 5-6 Wireless settin g : Non functioning key combination. Emulating Fn key on extern al keyboard The Fn key is only on Toshiba keyboards. If you use an external keyboard attached to the computer, you can execute Fn key combinations by emulating the Fn key.
T HE K EYBOARD 5-7 T urning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow mode To turn on the Arrow mode, press Fn + F10 . The Arrow mode indicator lights. Now try cursor and page control using the keys shown in figure 5-2.
User's Manual T HE K EYBOARD 5-8 T e mporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off.
T HE K EYBOARD 5-9 Generating ASCII chara cters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt . 2. Using the overlay keys, type the ASCII code.
User's Manual T HE K EYBOARD 5-10.
P OWER AND P OWER -U P M ODES 6-1 Cha pter 6 Power a nd Power-Up Mode s The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
6-2 User's Manual P OWER AND P OWER -U P M ODES Table 6-1 Power conditions continued Power on Power off (no operation) AC 2nd battery • Operates • LED: 2nd battery green adaptor fully • LED.
P OWER AND P OWER -U P M ODES 6-3 Table 6-1 Power conditions continued Power on Power off (no operation) AC 2nd battery • Operates adaptor charge • LED: 2nd battery off not is above DC IN off conn.
6-4 User's Manual P OWER AND P OWER -U P M ODES Power indicators The Main battery, Slim Select Bay , DC IN and Power indicators on the system indicator panel alert you to the computer’s operating capability and battery charge status.
P OWER AND P OWER -U P M ODES 6-5 Power indicator Check the Power indicator to determine the power status. Green Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates the power was turned off while the computer was in Resume mode.
6-6 User's Manual P OWER AND P OWER -U P M ODES Secondary battery (option) An optional secondary battery can be installed in the Slim Select Bay to increase your battery operating time. Note the caution on Resume mode in the previous section Main battery .
P OWER AND P OWER -U P M ODES 6-7 Care and use of the battery pack Care a nd use of the battery pa ck The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack.
6-8 User's Manual P OWER AND P OWER -U P M ODES Charging the batterie s When the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain.
P OWER AND P OWER -U P M ODES 6-9 The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions: ❑ The battery has not been used for a long time. ❑ The battery has completely discharged and been left in the computer for a long time.
6-10 User's Manual P OWER AND P OWER -U P M ODES M aximizing battery operating tim e A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ❑ How you configure the computer, for example, whether you enable battery- power saving options.
P OWER AND P OWER -U P M ODES 6-11 Care and use of the battery pack Extending battery life To maximize the life of your battery pack: ❑ ❑ ❑ ❑ ❑ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
6-12 User's Manual P OWER AND P OWER -U P M ODES Re pla cing the battery pa ck When the battery pack reaches the end of its operating life you will need to install a new one.
P OWER AND P OWER -U P M ODES 6-13 Figure 6-1 Removing the battery pack In stalling the battery pa ck To install a battery pack, follow the steps below. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of.
6-14 User's Manual P OWER AND P OWER -U P M ODES 2. Insert the battery pack. Figure 6-2 Installing the battery pack 3. Secure the battery pack lock. Starting the computer by pa ssword If you registered a password as supervisor or user, you must enter it to start the computer.
7-1 HW S ETUP AND P ASSWORDS Cha pter 7 HW Setup a nd Pa sswords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords.
User's Manual 7-2 HW S ETUP AND P ASSWORDS HW Setup window The HW Setup window contains the following tabs: Pointing Devices, Display, CPU, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer.
7-3 HW S ETUP AND P ASSWORDS Figure 7-2 HW setup window (Windows ® 2000) There are also three buttons: OK , Cancel and Apply . OK Accepts your changes and closes the HW Setup window. Cancel Closes the window without accepting your changes. Apply Accepts all your changes without closing the HW Setup window.
User's Manual 7-4 HW S ETUP AND P ASSWORDS General This window displays the BIOS version and contains two buttons: Default and About . Default Return all HW Setup values to the factory settings. About Display the HW Setup version.. Setup This field displays BIOS Version and date.
7-5 HW S ETUP AND P ASSWORDS HW Setup To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks.
User's Manual 7-6 HW S ETUP AND P ASSWORDS Parallel/Printer This tab lets you set the Printer Port Type. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bi-directional .
7-7 HW S ETUP AND P ASSWORDS HW Setup CPU NOTE: This feature appears only on computers with Mobile Intel® Pentium® III processor-M. Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically Switchable CPU power consumption and clock speed automatic switching function is enabled.
User's Manual 7-8 HW S ETUP AND P ASSWORDS CD-ROM −> −> −> −> −> LAN −> −> −> −> −> HDD −> −> −> −> −> FDD The computer looks for bootable files in the following order: CD-ROM*, LAN, HDD, diskette drive.
7-9 HW S ETUP AND P ASSWORDS HW Setup 2. The following menu will be displayed: Select Boot Device [C]: CD-ROM [N]: Network (LAN) [U]: USB Floppy Drive [1]: Primary Hard Drive (Built-in) [2]: Secondary Hard Drive (Select Bay) [P]: PC Card Drive Hard Drive [D]: Default SYSTEM SETUP Device Press [C], [N], [U], [1], [2], [P] or [D] NOTES: 1.
User's Manual 7-10 HW S ETUP AND P ASSWORDS Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use “Hotkeys” by pressing the set combination instead of the Fn key.
7-11 HW S ETUP AND P ASSWORDS Supervisor password LAN Wake-up on LAN This features lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Enables Wake-up on LAN. Disabled Disables Wake-up on LAN. (Default) CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled.
User's Manual 7-12 HW S ETUP AND P ASSWORDS.
8-1 O PTIONAL D EVICES Cha pter 8 Option al Device s Optional devices can expand the computer’s capabilities and its versatility. The following optional devices are available from your TOSHIBA deale.
8-2 User’s Manual O PTIONAL D EVICES PC cards The computer is equipped with a PC card expansion slot that can accommodate two 5 mm Type II cards or one 10.5 mm Type III card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed.
8-3 O PTIONAL D EVICES PC cards 3. Check the configuration in the HW Setup window to make sure it is appropri- ate for your card. 4. Slide the PC card lock into the locked position. Figure 8-2 Locking the PC card Re moving a PC card To remove the PC card, follow the steps below.
8-4 User’s Manual O PTIONAL D EVICES Figure 8-3 Removing the PC card Me mory expa n sion You can install additional memory in the computer’s memory module to increase the amount of RAM. 128,256 or 512MB memory modules can be installed in the two memory slots for a maximum of 1GB system memory.
8-5 O PTIONAL D EVICES 2. If you install a memory module that is not compatible with the computer, a beep will sound when you turn on the power. If the module is installed in slot A, there will be a long beep followed by a short beep. If the module is in slot B, there will be a long beep followed by two short beeps.
8-6 User’s Manual O PTIONAL D EVICES Figure 8-7 Inserting the memory module 8. Seat the cover and secure it with two screws. 9. When you turn the computer on, it should automatically recognize the total memory capacity. Use the HW Setup program to verify that the added memory is recognized.
8-7 O PTIONAL D EVICES Slim Select Bay 2nd battery pack Figure 8-8 Removing the memory module 7. Seat the cover and secure it with two screws. CAUTION: If only one memory module is installed, use slot A. Do not try to operate the computer with a module installed in slot B only.
8-8 User’s Manual O PTIONAL D EVICES In stalling To install the secondary battery pack in the adaptor, follow the steps below. 1. Fit the side of the secondary battery pack opposite the connector into the adaptor. 2. Lay the battery into the adaptor.
8-9 O PTIONAL D EVICES Addition al AC a da ptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load: PA3083*.
8-10 User’s Manual O PTIONAL D EVICES 2. Insert the HDD and push forward to ensure a firm connection. Figure 8-12 Installing the HDD 3. Close the lid and slide the lock to the lock position. Figure 8-13 Closing the lid For details on installing the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating Basics .
8-11 O PTIONAL D EVICES USB dis kette drive The 3 1/2" external diskette drive module can be connected to the USB port. For details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4, Operating Basics .
8-12 User’s Manual O PTIONAL D EVICES Parallel printer You can connect any standard Centronics-compatible parallel printer to your computer. All you need is an IBM PC™ parallel printer cable. Your dealer can supply one or you can purchase one at most computer stores.
8-13 O PTIONAL D EVICES External monitor Extern al monitor An external analog monitor can be connected to the external monitor port on the computer, Port Replicator. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below.
8-14 User’s Manual O PTIONAL D EVICES T elevision A television can be connected to the video out port on the computer. To connect a television, follow the steps below. 1. Turn the computer off. 2. Use a video cable (not supplied) to connect the television to the video out port.
8-15 O PTIONAL D EVICES PS/2 keyboard 1. Turn the computer off. 2. Connect the PS/2 mouse to the PS/2 keyboard/mouse port on the computer or the mouse port on the optional Advanced Port Replicator, pressing gently to assure a firm connection. 3. Turn on the computer.
8-16 User’s Manual O PTIONAL D EVICES Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer.
9-1 T ROUBLESHOOTING Ch a pter 9 T roubl e shooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter.
User's Manual 9-2 T ROUBLESHOOTING ❑ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer.
9-3 T ROUBLESHOOTING Hardware a nd syste m checklist This section discusses problems caused by your computer’s hardware or attached peripherals. Basic problems may occur in the following areas: ❑ .
User's Manual 9-4 T ROUBLESHOOTING Self te st When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system.
9-5 T ROUBLESHOOTING Overheating power down If the computer’s internal temperature becomes too high, the computer will auto- matically enter Hibernation or Resume mode and shut down. Problem Procedure Computer shuts down Leave the computer off until the DC IN indicator and DC IN indicator stops blinking.
User's Manual 9-6 T ROUBLESHOOTING Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the computer, contact your dealer.
9-7 T ROUBLESHOOTING Hardware and system checklist Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary wipe them with a soft dry cloth dipped in alcohol. Connect the AC adaptor and replace the battery. Make sure it is securely seated.
User's Manual 9-8 T ROUBLESHOOTING Keyboard Keyboard problems can be caused by your setup configuration. For more informa- tion refer to Chapter 5, The Keyboard and Chapter 7, HW Setup and Passwords . Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers selected.
9-9 T ROUBLESHOOTING Hard dis k drive Problem Procedure Computer does not Check if a diskette is in the diskette drive. If a boot from hard disk diskette is inserted, remove it and reboot. drive There may be a problem with your operating system files.
User's Manual 9-10 T ROUBLESHOOTING A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner.
9-11 T ROUBLESHOOTING A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner.
User's Manual 9-12 T ROUBLESHOOTING A foreign object in the drawer could block laser light from reading the DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner.
9-13 T ROUBLESHOOTING DVD does not play Some video discs might not play properly in a correctly in an Expansion Station. Play the disc in the optional Expansion DVD-ROM drive installed in the computer. Station If problems persist, contact your dealer.
User's Manual 9-14 T ROUBLESHOOTING Check the type of DVD/CD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: Audio CD, Photo CD, ISO 9660, CD-EXTRA, CD-R, CD-Rewritable Check the region code on the DVD. It must match that on the DVD drive.
9-15 T ROUBLESHOOTING Infrared port Refer also to the documentation for your IrDA compatible device and related software. Problem Procedure Infrared devices do Check that the device is connected to an not work as expected electric outlet. Make sure the outlet is supplying power by plugging in an appliance.
User's Manual 9-16 T ROUBLESHOOTING Make sure your software is configured to recog- nize the printer. Check your printer and software documentation.
9-17 T ROUBLESHOOTING Is your software configured to recognize the mouse? Check the software documentation. If problems persist, contact your dealer. Serial mouse Problem Procedure On-screen pointer Check for a firm connection between the does not respond to computer’s serial port and the cable’s 9-pin serial mouse operation connector.
User's Manual 9-18 T ROUBLESHOOTING Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not Make sure that the external monitor’s power turn on switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.
9-19 T ROUBLESHOOTING Sound syste m Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure.
User's Manual 9-20 T ROUBLESHOOTING Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, Keyboard . NOTE: If you turn the computer off in Resume mode while the display is on TV, the computer will select either the internal LCD or an external computer CRT as the display device.
9-21 T ROUBLESHOOTING Mode m Refer to the online help files for Appendix C and D . Problem Procedure Communication Make sure the computer’s internal modem software can't settings are correct. Refer to Phone and Modem initialize modem Options in the Control Panel.
User's Manual 9-22 T ROUBLESHOOTING A CONNECT display Check the error control setting in your is quickly replaced by communications application. NO CARRIER You can also use the ATN command. Refer to the chapter on AT commands in online help files for Appendix C, AT Commands.
9-23 T ROUBLESHOOTING Me mory expa nsion Refer also to Chapter 8, Optional Devices , for information on installing memory modules. Problem Procedure Beep sounds. Make sure the memory module installed in the (If slot A two beeps, expansion slot is compatible with the computer.
User's Manual 9-24 T ROUBLESHOOTING Wirele ss LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on.
9-25 T ROUBLESHOOTING Outside of Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Canada TOSHIBA of Canada Ltd. 191 McNabb Street, Markham, Ontario L3R 8H2 Singapore TOSHIBA Singapore Pte.
User's Manual 9-26 T ROUBLESHOOTING.
A-1 A PPENDIX A Appendix A Sp e ci f icatio n s This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 316 (w) x 275 (d) x 33.9/38.1 (h) millimeters (does not include the thicker part of the bottom of the computer) Weight CD/DVD Display Kilograms DVD-ROM 14" XGA-TFT 2.
A-2 A PPENDIX A User's Manual 50 or 60 hertz (cycles per second) Computer 15 VDC 5.0 amperes Built-in Modem Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Typ.
B-1 A PPENDIX B Appendix B Display Controller a nd Mode s Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off.
User's Manual B-2 A PPENDIX B Video mode s The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
B-3 A PPENDIX B Table Video modes continued Video Type Resolution Character LCD CRT Scanning mode matrix colors colors frequency (pels) Vertical D VGA 320 x 200 8 x 8 16 of 256K 16 of 256K 70Hz Grph P.
User's Manual B-4 A PPENDIX B Table Video modes continued Video Type Resolution Character LCD CRT Scanning mode matrix colors colors frequency (pels) Vertical SVGA 640 x 480 64K of 64K 64K of 64K.
C-1 A PPENDIX C Appendix C A T Comma nds In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
User's Manual C-2 A PPENDIX C A Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps.
C-3 A PPENDIX C Appendix C ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S=n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information).
User's Manual C-4 A PPENDIX C Ln Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0 ) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode This command turns the speaker on or off.
C-5 A PPENDIX C Appendix C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode.
User's Manual C-6 A PPENDIX C T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received.
C-7 A PPENDIX C Appendix C X5 Ena ble Enable OK, RING, NO CARRIER, ERROR, NODIAL TONE, BUSY , CONNECT <RA TE>, RRING, NO BONGTONE, DELA YED, BLACKLISTED, REOR DER, W ARBLE, CALL W AITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone.
User's Manual C-8 A PPENDIX C &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default).
C-9 A PPENDIX C Appendix C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.
User's Manual C-10 A PPENDIX C &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
C-11 A PPENDIX C Appendix C Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. N0 Buffer mode. No error control. N1 Direct mode. N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures.
User's Manual C-12 A PPENDIX C Vn Protocol result code V0 Disable protocol result code appended to DCE speed. V1 Enable protocol result code appended to DCE speed (default).
C-13 A PPENDIX C Appendix C.
D-1 A PPENDIX D Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails.
User's Manual D-2 A PPENDIX D S0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command.
D-3 A PPENDIX D S4 Response formatting character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer.
User's Manual D-4 A PPENDIX D S7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer).
D-5 A PPENDIX D S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = .
User's Manual D-6 A PPENDIX D A T comma nd set re sult code s The following table shows the result codes. The result code summary Result Code Numeric Description OK 0 Command executed CONNECT 1 M.
D-7 A PPENDIX D Result Code Numeric Description DELAYED* 2 88 Delay is in effect for the dialed number BLACKLISTED* 2 8 9 Dialed number is blacklisted BLACKLIST FULL* 2 9 0 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled.
User's Manual D-8 A PPENDIX D.
E-1 A PPENDIX E Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.
User's Manual E-2 A PPENDIX E Table E-1 Result codes for a V.90 connection No. Result code Description 70 CONNECT 32000 EC* Connection at 32000 bits/s 72 CONNECT 36000 EC* Connection at 36000 bit.
E-3 A PPENDIX E A T Comma nd -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
User's Manual E-4 A PPENDIX E.
Appendix F Wirele ss LAN This document is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. About T oshiba W irele ss solution The Wireless LAN card Kit enables you to: ❑ Connect your computer to a peer-to-peer workgroup of Wireless computing devices.
F-2 User’s Manual A PPENDIX F Peer-to-peer workgroup The peer-to-peer workgroup configuration enables you to quickly set up a small Wireless workgroup, where the workgroup participants can exchange files using features such as Files and Printer Sharing as supported by Microsoft Networking.
F-3 A PPENDIX F Appendix F Enterprise networking Figure F-2 Stand-alone Wireless LAN With the Wireless LAN Access Points you can connect to a corporate Local Area Network (LAN) infrastructure to have Wireless access to all network facilities. LAN Infrastructures may either be.
F-4 User’s Manual A PPENDIX F ❑ Wireless network infrastructures connected to an existing Ethernet network as pictured in Figure F-3. Figure F-3 LAN Infrastructure Ea sy configuration The Wireless LAN card functions like any standard wired Ethernet card except it gives you the freedom of Wireless connections.
F-5 A PPENDIX F Appendix F Wirele ss LAN card type s The Wireless LAN card is a Wireless network card that complies with the IEEE 802.11 standard on Wireless LANs (Revision B). The Wireless LAN card supports data rates up to 11 Mbit/s. ❑ Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA).
F-6 User’s Manual A PPENDIX F 5. Set the correct Network Name . Figure F-4 Edit Configuration window 6. In the field Network Name , define the name of the Wireless network to which you want to connect. You can either use: • The value ANY To connect to any Wireless LAN network in the vicinity of your computer.
F-7 A PPENDIX F Appendix F Ba sic settings for peer-to-peer workgroups If you wish to connect to a peer-to-peer workgroup, use the Add/Edit Configuration Profile window to: 1. Click the Start button from the Windows task bar. 2. Click on Settings , and then on Control Panel .
F-8 User’s Manual A PPENDIX F • If there is not yet such a group available, your computer will automatically start one with this name. 7. Click OK to confirm and return to the Add/Edit Configuration Profile window.
F-9 A PPENDIX F Appendix F 4. To display other workgroups in the network environment, double-click the Entire Network icon. If you cannot find other Wireless LAN networked computers, verify whether the other Wireless LAN computers are: ❑ Powered up and logged onto the network.
F-10 User’s Manual A PPENDIX F ❑ Click the icon once with your right mouse button to display a menu with more options. View W irele ss link quality You can use Client Manager icon on the Windows task bar to verify the link quality of your network connection.
F-11 A PPENDIX F Appendix F V iew/modify W ireless LAN card settings If you would like to view or modify Wireless LAN parameters, for example because you would like to connect to another network or type of network, proceed as follows: 1. Right-click on the Client Manager icon on the Windows task bar.
F-12 User’s Manual A PPENDIX F Adva nced configuration s Although your Wireless LAN card will work fine in most network environments with the Basic Parameters , you may wish to explore the advanced parameters options as displayed in the Wireless LAN card’s Edit Configuration window.
F-13 A PPENDIX F Appendix F Adva nced window Use this window to set advanced parameters. Figure F-8 Advanced window Card Power Management To extend the battery life of (mobile) Wireless devices.
F-14 User’s Manual A PPENDIX F Admin window You can set the following parameters in the Admin window. Figure F-9 Admin parameters Distance between Depending on the number of access points in a Wireless access points LAN network this parameter controls the network performance.
F-15 A PPENDIX F Appendix F Card specif ication s Table F-2 Physical specifications Form Factor Mini-PCI TypeIIIA Dimensions Weight Temperature and Humidity Operation 0 to 55 C Maximum humidity 95% Tr.
F-16 User’s Manual A PPENDIX F Receive Mode 250mA Transmit Mode 350mA Power Supply 3.3V Table F-4 Networking Characteristics Compatibility ■ IEEE 802.
F-17 A PPENDIX F Appendix F Wireless communication is often subject to local radio regulations. Although Wireless LAN networking products have been designed for operation in the license- free 2.4 GHz band, local radio regulations may impose limitations on the use of Wireless communication equipment.
F-18 User’s Manual A PPENDIX F Table F-5 lists the typical ranges when used indoors in office environments such as the following: ❑ In Open Office environments , where antennas can see each other, i.e. there are no physical obstructions between them.
G-1 A PPENDIX G Appendix G AC Power Cord a nd Conne ctors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.
G-2 User's Manual A PPENDIX G The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
H-1 A PPENDIX H Appendix H Intern al Mode m Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described.
H-2 User’s Manual A PPENDIX H Re moving the mode m board To remove the internal modem. 1. Save your data, quit Windows and turn off the power. 2. Disconnect the AC adaptor and any other peripheral devices. 3. Turn the computer upside down and remove the battery pack.
A PPENDIX I I-1 Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, Slim Select Bay modules and communication devices.
A PPENDIX I User's Manual I-2 Conf iguration s The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart.
G LOSSARY Glossary-1 Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference. Abbreviation s AC: alternating current AGP: accelerated .
G LOSSARY Glossary-2 alphanumeric: Keyboard characters including letters, numbers and other symbols, such as punctuation marks or mathematical symbols. alternating current (AC): Electric current that reverses its direction of flow at regular intervals.
G LOSSARY Glossary-3 asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals.
G LOSSARY Glossary-4 C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
G LOSSARY Glossary-5 compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
G LOSSARY Glossary-6 device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
G LOSSARY Glossary-7 execute: To interpret and execute an instruction. Extended Capability Port: An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support.
G LOSSARY Glossary-8 hot dock/undock: Connecting or disconnecting a device to or from the computer while the computer’s power is turned on. hotkey: The computer’s feature in which certain keys in combination with the extended function key, Fn , can be used to set system parameters, such as speaker volume.
G LOSSARY Glossary-9 MDA: Monochrome Display Adapter. A video display protocol defined by the IBM Monochrome Display Adapter and its associated circuitry for direct drive TTL displays that supports a mono- chrome 720x350 text mode. megabyte (MB): A unit of data storage equal to 1024 kilobytes.
G LOSSARY Glossary-10 monitor: A device that uses rows and columns of pixels to display alphanu- meric characters or graphic images. See CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment.
G LOSSARY Glossary-11 parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd.
G LOSSARY Glossary-12 serial: The handling of data bits one after the other. serial communications: A communi- cations technique that uses as few as two interconnecting wires to send bits one after another. serial interface: Refers to a type of information exchange that transmits information sequentially, one bit at a time.
G LOSSARY Glossary-13 S-video: This connection provides separate lines for contrast and color, which produces a video image superior to that produced by a composite connection. See also RCA jack. synchronous: Having a constant time interval between successive bits, characters or events.
G LOSSARY Glossary-14.
Index-1 I NDEX Index A AC adaptor 1-6, 2-11 DC IN 15V port 2-4 additional 1-12, 8-11 connecting 3-5 AccuPoint II 1-6, 2-7 problems 9-16 using 4-1 Advanced Port Replicator 1-12, 8-11 ASCII characters 5.
Index-2 User's Manual I NDEX E Environment 3-2 Equipment checklist 1-1 Equipment setup general conditions 3-2 placement 3-2 Ergonomics lighting 3-4 seating and posture 3-3 work habits 3-4 Expansi.
Index-3 I NDEX K Keyboard 1-5, 5-1 emulating enhanced keyboard 5-2 F1 . . . F12 function keys 5-2 problems 9-8 Typewriter keys 5-1 Keypad overlay 1-9, 5-6 arrow mode 5-7 numeric mode 5-7 temporarily c.
Index-4 User's Manual I NDEX LAN 2-4 microphone, See Sound system modem 2-4 parallel 1-6, 2-4 PS/2 keyboard/mouse 1-6, 2-4 serial 1-6, 2-4 USB 1-6, 2-4 Power auto power on 1-10 button location 2-.
Index-5 I NDEX Soft keys 5-2 cursor control mode 5-3 Enter 5-3 numeric mode 5-3 right Alt key 5-3 right Ctrl key 5-3 ScrLock 5-3 Sound system 1-7 drivers 1-11 headphone 1-6, 2-1 microphone 1-6, 2-1 pr.
Index-6 User's Manual I NDEX.
Ein wichtiger Punkt beim Kauf des Geräts Toshiba TE2000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toshiba TE2000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toshiba TE2000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toshiba TE2000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toshiba TE2000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toshiba TE2000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toshiba TE2000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toshiba TE2000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toshiba TE2000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
