Benutzeranleitung / Produktwartung L640 des Produzenten Toshiba
Zur Seite of 229
GMAD0025101 2 0 3 /10 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 162 in this gui de.
2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical ap.
4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n.
5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can.
6 5.375 x 8.375 ver 2.3 In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer . Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your al arm equipment.
7 5.375 x 8.375 ver 2.3 3 The standard connecting arrangemen t (telephone jack type) for this equipment is jack t ype(s): USOC RJ11C. Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card.
8 5.375 x 8.375 ver 2.3 Wireless LAN and Y our Health W ireless LAN products, like other radio de vices, emit radio frequency electromagnetic energy . The lev el of energy emitted by W i reless LAN devices howe ver is f ar much less than the elect romagnetic energy emitted b y wireless devices lik e for example mobile phones.
9 5.375 x 8.375 ver 2.3 Canada – Indust ry Canada (IC) This device complies with RS S 210 of Industry Canada. The installer of this radio equipment mu st ensure that the antenna is loc ated or point.
10 5.375 x 8.375 ver 2.3 EU Declaration of Conformity TOSHIB A declares that this product conforms to the follo wing Standards: This product is carrying the CE-Mark in accordance w ith the related European Directiv es. The party responsib le for CE-Marking is TOSHIB A Europe GmbH, Hammfelddamm 8, 41460 Neuss, Ger many .
11 5.375 x 8.375 ver 2.3 VCCI Class B Information Modem W arning Notice This information is only applicable if your computer has a modem. Conformity Statement The equipment has been ap prov ed to [Commission D ecision “CTR21”] for pan- European single terminal connection to the Public Switched T elephone Network (PSTN).
12 5.375 x 8.375 ver 2.3 Using this Equipment in Japan In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for sec ond generation low-po wer data communicatio n systems such as this equipment ov erlaps that of mobile object identifi cation systems (premises radio station and specified lo w-power radio station).
13 5.375 x 8.375 ver 2.3 The indication sho wn belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.
14 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is de pendent on what type of wi reless device is in your computer .
15 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 622ANHMW and 633ANHMW Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
16 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Atheros ® Wireless Wi-Fi ® Link AR5B95 Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
17 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries Ukraine United Kingdom Uruguay USA V enezuela V ietnam Y emen Zimbabwe België/ Belgique: For pri vate usage outside b uildings acr oss public grounds over less than 300m no special regi stration with IB PT/BIPT is required.
18 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply .
19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8192E This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
20 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8191SE This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table.
22 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that.
23 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table.
24 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnology and Y our Health The products with Bluetooth ® wireless technolog y , like other radio de vices, emit radio frequency electromagnetic ener gy .
25 5.375 x 8.375 ver 2.3 Regulator y statements This product complies with any mandatory product specification in any country/ region where the product is sold.
26 5.375 x 8.375 ver 2.3 Optical Disc Drive Safety Instructions This appliance contains a laser syst em and is classified as a CLASS 1 LASER PRODUCT . T o use this model prop erly , rea d th e user’ s guide carefully and keep it for your fut ure reference.
27 5.375 x 8.375 ver 2.3 Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and ma y be subject to the approv al of the U.S. Department of Commerce prior to export.
28 5.375 x 8.375 ver 2.3 T rademarks Satellite and eco Utility are either registered trademarks or trad emarks of T oshiba America Information Systems, In c. and/or T oshiba Cor poration. Adobe and Photoshop are either registered trademarks or tr ademarks of Adobe Systems Incorporated in the Unite d States and/or other countries.
29 5.375 x 8.3 75 ver 2.3 Contents Introduction ................ ................................................................ 36 This guide ...............................................................38 Safety icons ............................
30 Contents 5.375 x 8.3 75 ver 2.3 Using the computer fo r the first time ......................48 Opening the display panel ................................. 48 Turning on the power .......................................49 Setting up your software .
31 Contents 5.375 x 8.3 75 ver 2.3 Using an external keyboard ..................................... 82 Using a mouse ........................................................82 Connecting a printer ...............................................82 Setting up a printer .
32 Contents 5.375 x 8.3 75 ver 2.3 Using the optical disc drive ................................... 107 Viewing Blu-ray Disc™ movies .......................107 Optical disc drive components ........................ 109 Inserting an optical disc ....
33 Contents 5.375 x 8.3 75 ver 2.3 Disposing of used batteries ..................................129 Traveling tips ........................................................ 130 Chapter 4: Exploring Y our Co mputer’ s Features ................... 131 Exploring the desktop .
34 Contents 5.375 x 8.3 75 ver 2.3 TOSHIBA eco Utility™ ...........................................160 TOSHIBA Service Station ......................................161 TOSHIBA PC Health Monitor .................................161 Chapter 6: If Something Goes Wrong.
35 Contents 5.375 x 8.3 75 ver 2.3 Appendix A: Hot Keys/TOSHI BA Cards ........... ...................... 190 Hot Key Cards .......................................................190 Using the Hot K ey Cards .................................191 Application Cards .
36 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go.
37 Introduction 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 30% and 60% less energ y depending on how it is used.
38 Introd uctio n This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated.
39 Introduction Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipmen t, or loss of data.
40 Introd uctio n Other documentation 5.375 x 8.375 ver 2.3 Y our computer’ s features and specifications Certain computer chassis are de signed to accommodate all possible configurations for an entire product Series.
41 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information.
42 Getting Started Selecting a place to work T o keep your computer in prime operating condition, pro tect your work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
43 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin.
44 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that cools t he CPU by drawing outside air into the computer .
45 Getting Started Connecting to a po wer sour ce Please handle your computer carefully to avoi d scratching or damaging the surface. Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery .
46 Getting Started Connecting to a power so ur ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord /cable to .
47 Getting Started Char ging the main battery ❖ Flashes amber when the main battery char ge is lo w and it is time to recharge the main battery or plug in the A C adaptor If the AC power light flashes amber during charging, either the main battery is malfunctioning, or it is not receiving correct input from the AC power supply .
48 Getting Started Using the computer for the fir st time Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Facing the front of the com puter, locate the center of the display panel.
49 Getting Started Using the computer for the f irst time T urning on the power T o turn on the computer: 1 Make sure an y external de vices (such as the A C adaptor , if you plan to use AC po wer rather th an battery power) are properly connected and ready .
50 Getting Started Re gistering your computer with T o shiba Registering your computer with T oshiba Product registration is strongly recommended, and allows T oshi ba to send you periodic updates, announcements , and special offers applicable to your prod uct.
51 Getting Started Adding memory (optional) Before adding external devices or memory , T oshiba recommends setting up your software. See “Setting up your s oftware” on page 49 . Installing a memory module Memory modules can be installed in the memory mo dule slots on the base of the computer .
52 Getting Started Adding memo ry (optional) If the computer is on, begin at step 1 ; otherwise, skip t o step 3 . 1 Click Start . (Sample Image) Shut down button 2 Click the Shut do wn button in the lo wer-right corner of the Start menu. The computer closes all open programs, shuts down the operating system, and then turns off.
53 Getting Started Adding memory (optional) 6 Using a small Phillips screwdri ver , loosen the capti ve scre ws that secure the memory module slot co ver . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cover .
54 Getting Started Adding memo ry (optional) For this model, Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. 11 Pick up the memory modul e by its sides, a voiding an y contact with its connector .
55 Getting Started Adding memory (optional) 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard on the top edge of the module to seat the module into the latches at the sides of the so cket. These latches should “snap” into place securely with th e corresponding cutouts in the side of the module.
56 Getting Started Adding memo ry (optional) 14 Replace the memory modu le slot cov er and secure it using the screws. 15 Re-insert the main battery . For more information on i nserting the main battery , see “Inserting a char ged battery” on page 126 .
57 Getting Started Adding memory (optional) Removing a memor y module If you need to remov e a memory module: 1 Complete steps 1 – 8 in “Installing a memory modu le” on page 51 to shut down the computer an d open the me mory module slot cov er .
58 Getting Started Adding memo ry (optional) 3 Gently lift the me m o ry module to a 30-degree angle and slide it out of the slot. (Sample Illustration) Removing the memory module 4 Replace the memory modu le slot cov er and secure it using the screws.
59 Getting Started Recovering the Internal Stora ge Drive 7 Reconnect the cables. 8 Restart the computer . TECHNICAL NOTE: Y ou must have at least one memory module installed for the computer to work. Checking total memory When you add or remove a memory mo d u l e , you can check that the computer has recognized the change.
60 Getting Started Recovering the Internal Stor age Drive A recov ery image of your computer is stored on the internal storage dri ve, and the image can be restored b y running the recov ery utilities directly from you r internal storage driv e as described in the sections below .
61 Getting Started Recovering the Internal Stora ge Drive Recovering to out-of-box state (recommended recovery method) Recoverin g an internal storage driv e to its out-of-box state deletes all partitions on the drive and all info rmation stored in those partitions.
62 Getting Started Recovering the Internal Stor age Drive (Sample Image) W arning screen 5 When the T oshiba Recov ery W izard opens and the Selecting a process screen displays, select Recovery of F actory Default Software and then click Next . (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
63 Getting Started Recovering the Internal Stora ge Drive (Sample Image) Reco very of F a ctory Defa ult Software scr een 7 Click Next . A confirmation message displays reminding you that all data will be lost during the recov ery process. Be sure to sav e your work to e xternal media before proceeding (see “Backing up your work” on page 106 ).
64 Getting Started Recovering the Internal Stor age Drive The “Recov er to a custom size pa rtition” option restores you r C: dri ve to its out-of-box state, and allows you to specify the size for the C: partition.
65 Getting Started Recovering the Internal Stora ge Drive 5 When the T oshiba Recov ery W i zard opens and the Selecting a process screen displays, select Recovery of F actory Default Software and then click Next . (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears.
66 Getting Started Recovering the Internal Stor age Drive 8 Click Next . A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to sa ve your work to e xternal media before proceeding (see “Backing up your work” on page 106 ).
67 Getting Started Recovering the Internal Stora ge Drive 4 A warning screen appears stati ng that when the recov ery is ex ecuted all data will be deleted and rewritten.
68 Getting Started Recovering the Internal Stor age Drive 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover without changing the hard drive partitions . (Sample Image) Reco very of F a ctory Default Software scr een 7 Click Next .
69 Getting Started Recovering the Internal Stora ge Drive When you create recovery DVDs/media, only the operating system files, applications, and drivers originally shipped with the computer are backed up to the external media and can be rest ored from this media.
70 Getting Started Recovering the Internal Stor age Drive Y ou cannot store your system’ s applications on the same drive or disc/disc set where the rest of the system recovery files are stored. For example, you will need to store the applications on one USB flash drive and the system recover y files on another USB flash drive.
71 Getting Started Recovering the Internal Stora ge Drive Restoring from recovery DVDs/media The recovery process deletes information stored on the internal storage drive. Be sure to save your work to externa l media before executing the recovery (see “Backing up your work” on page 106 ).
72 Getting Started Recovering the Internal Stor age Drive 2 Do one of the following: ❖ If your recov ery files are on D VDs, insert the first recov ery D VD into your optical disc driv e. ❖ If your recov ery files are on a USB flash driv e, connect the USB flash driv e to your computer .
73 Getting Started Erasing the Internal Storag e Drive Erasing the Internal Storage Drive Erasing the internal storage drive will delete all data on the drive, including the partitions. Be sure to create recovery DVDs/media and back up your data to external media before erasing the internal storage drive.
74 Getting Started Checking the inte rnal stor age drive operating status (Sample Image) Er ase the har d disk scr een 4 Click Next . A confirmation message displays reminding you that all data on the internal storage driv e will be lost.
75 Getting Started Using the T ouchP ad™ Installing drivers and applications The T osh iba Application Installer allows you to reinstall the driv ers and applications that were original ly bundled with your computer .
76 Getting Started Using the T ouchP ad™ Refer to the table belo w for speci f ic instructio ns on performing each operation. The pointer is the icon (usually an arrow) that moves on the screen when you slide your finger across the T ouchPad or move a mouse connected to your computer .
77 Getting Started Using the T ouchP ad™ Scroll vertically Slide your finger along the right edge of the T ouchPad in the direction you want to scroll.
78 Getting Started Using the T ouchP ad™ Adjusting T ouchPad™ settings While you are typing, the on-screen pointer may seem to move or jump around “by itself” to ran dom locations on the screen. The on-screen pointer may also seem to automatically select text, click buttons, and acti vate other user interf ace elements.
79 Getting Started Using external display de vices T ouchPad setting options vary by computer model. The T ouchPad settings are accessible through the Mou se Properties option of the Windows Control Panel. For more information, please visit www .support.
80 Getting Started Using external display de vices Selecting video cables T o connect a device to the HDMI™ O ut port, you must purchase an HDMI™ cable.
81 Getting Started Using external display de vices Directing the display output when you turn on the computer Once you ha ve connected an e xte rnal displ ay devi ce, you can choose to use the internal display only , the external de vice only , or both simultaneo usly .
82 Getting Started Using an e xternal ke yboar d 3 Release the Fn key . Adjusting the quality of the external display T o obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.
83 Getting Started Connecting a printer TECHNICAL NOTE: T o determine if your printer supports Plug and Play , check its documentation. If your printer does not suppo rt Plug and Play , you can set up the printer as described in “Setting up a printer” on page 83 .
84 Getting Started T urning off the computer T urning off the computer Pressing the power button before shutting down the Windows ® operating system could cause you to lose your work . Make sure the system indicator panel’ s storage drive light and the drive in-use light are off.
85 Getting Started T urning off the computer Hibernation mode Hibernation mode shuts th e computer down completely , but it f irst sav es the current state of the comput er to the internal storage driv e. Since Hibernation mode does not require power to maintain the sav ed information, system settings are retained indefinitely .
86 Getting Started T urning off the computer ❖ Restarting from Sleep takes le ss time and consumes less main battery power than restarting after turning off the computer using the Hibernation or Shut down commands.
87 Getting Started T urning off the computer T urning off the computer more quickly Y ou can also turn off the computer by pressing the po wer b utton. T o use this method, you first need to acti vate it using the Po wer Options feature. By default, pressin g your computer’ s po wer button puts the computer into Sleep mo de.
88 Getting Started T urning off the computer 4 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options scr een 5 Select the options you want from the drop-down lists.
89 Getting Started T urning off the computer Restarting your computer T o start the computer up again, press the po wer b utton unti l the ON/OFF light glows white. If you turn off the computer by closing the display panel, you can start it again by open i ng the display panel .
90 Getting Started T urning off the computer 2 Click Change pl an settings under the power plan to be customized. The Edit Plan Settin gs window appears. (Sample Image) Edit Plan Settings screen 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears.
91 Getting Started T urning off the computer These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power . ❖ Lid close action Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the display panel.
92 Getting Started T urning off the computer 2 Click Sleep in the pop-up menu. The computer sa ves the status of all open programs and files to the memory , turns off the display , and enters into a low-po wer mode. The ON/OFF light blinks am ber indicating the computer is in Sleep mode.
93 Getting Started T urning off the computer 4 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 5 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options scr een 6 Select Sleep for the options you want.
94 Getting Started Customizing your comp uter’ s settings Starting again from Sleep mode T o start up the computer from Sleep mode, press the power b utton until the ON/OFF light glows white.
95 Getting Started Caring for your computer Moving the computer Before moving your computer, e v en across the room, make sure all driv e activity has ende d (the intern al storage dri ve and optical disc driv e indicator lights stop glowing) and all external peripheral cables are disconnected.
96 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive.
97 Learning the Basics Using the ke yboar d ❖ Use Error-checking and Disk Defr agmenter re gularly to check and optimize disk space a nd improv e performance. ❖ Scan all ne w files for viruses. This precaution is especially impor tant for f iles you receiv e via external media, email, or download from the Internet.
98 Learning the Basics Using the ke yboar d L650 series k eyboard T o capture a print screen of the entire screen, press the Fn + PRTSC key . T o capture only the active window displayed, press Fn + AL T while simultaneously pressing the PR TSC key .
99 Learning the Basics Using the ke yboar d Ctrl, Fn, and Alt keys (Sample Illustration) Ctrl, Fn, and Alt keys The Ctrl , Fn , and Alt keys do different things depending on the program you are using. For more inform ation, see your prog ram documentation.
100 Learning the Basics Using the ke yboar d Overlay keys This section applies to the L640 series. The ke ys with gray numbers and symbols on the front of them form the numeric and cursor ov erlay . This ov erlay lets you enter numeric data or control the cursor as you would using the 10-key ke ypad on a desktop comput er’ s k eyboa rd.
101 Learning the Basics Starting a pr o gram Using the overlay for cursor control This section applies to the L640 series. The keys with the gray arro ws a nd symbols on their left front are the cursor control overlay k eys. T o turn the cu rsor control overlay on, press Fn and F10 simultaneously .
102 Learning the Basics Starting a pr ogr am 2 Click the program group, in this example, Accessories . The Accessories menu is displayed. 3 Click the pr ogram, in thi s example, Wo r d P a d . W ordPad opens. T o close the program, click the Clo se button in the upper -right corner of the program’ s window .
103 Learning the Basics Saving your work Starting a program using the Search programs and files field This example uses the Start menu’ s Search programs and f iles field to start W ordPad: 1 Click Start to display the Start menu. The Search programs and files f ield appears at the bottom of the Start menu.
104 Learning the Basics Saving your work Saving files 1 Click on the arrow in the upper -left corner of your W indows ® -based application to display the drop-down menu, and then click Sav e . If you are working with a docum ent that already has a f ile name, this i s all you need to do.
105 Learning the Basics Printing your work Using a file extension Most programs assign an extension to the f ile name that identifies the file as being created in the pr ogram with a particular format. F or example, Microsoft ® W ord saves f iles with a .
106 Learning the Basics Backing up your work 3 Specify the print parameters. For e xample, the range of pages and number of copies to print. 4 Click Print . Backing up your work Back up all the files you create in case something happens to your computer .
107 Learning the Basics Using the optical disc drive TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to over write a file that already exists on the internal storage drive. Make sure the backup v ersion is the one you want before overwriting the existing file.
108 Learning the Basics Using the optical disc drive ❖ Some Blu-ray Disc™ movies hav e online content that can be accessed from the disc. T o view this content, your computer must be connected to the Intern et.
109 Learning the Basics Using the optical disc drive Optical disc drive components The optical disc dri ve is located on the side of the computer . Y our optical disc driv e may look like this: (Sample Illustration) Optical disc drive Drive in-use indicator light —Indicates when the driv e is in use.
110 Learning the Basics Using the optical disc drive 4 Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended 5 Hold the disc by its edges and check that it is free of dust. If the disc is dusty , clean it as described in “Caring for optical discs” on page 113 .
111 Learning the Basics Using the optical disc drive If you insert the disc incorrectly , it may jam the drive. If this happens, contact T oshiba support for assistance. 9 Push the disc tray in by pressing gently on th e center of the tray until it clicks into place.
112 Learning the Basics Using the optical disc drive For more information regarding supported optical media formats please refer to your computer’ s detailed specif ications at pcsupport.toshiba.com . Due to manufacturing and quality variations in third party optical media (e.
113 Learning the Basics T oshiba’ s online r esour ces Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. 2 Pull the tray out until it is fully open , remove the disc, and place it in its protecti ve co ver .
114 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your comput er while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process.
115 Mobile Computing Running the computer on battery power Battery Notice Battery life rating is for comparison purposes only , and does not indicate the battery life that will be obtained by any indi vidual user .
116 Mobile Computing Char ging batteries TECHNICAL NOTE: Depending on your system, the RTC battery may only charge while the computer is turned on. Power management Y our computer ships with t he powe.
117 Mobile Computing Char ging ba tteries Charging the main battery T o charge the main battery while it is in your computer, plug the computer into a li ve electrical ou tlet.
118 Mobile Computing Monitoring main battery power T o recharge the R TC battery , plug the computer into a li v e electrical outlet and leav e the computer powered on for 24 hours. It is seldom necessary to charge the RTC battery because it charges while the computer is on.
119 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the battery light ( ), the ON/OFF light ( ), and the powe r button light (near the upper -left corner of the keyboard).
120 Mobile Computing Monitoring main battery power TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaini ng charge frequently if you are working in temperatures below 50 degrees Fahrenheit.
121 Mobile Computing Monitoring main battery power 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 4 Double-click Battery to display the battery op tions. (Sample Image) Advanced settings tab of P ower Options scr een 5 Configure the alarm settings to suit your needs.
122 Mobile Computing Monitoring main battery power These power -sa ving options contro l the way in which the computer is configured. By using them, y ou can increase the length of time you can use the computer before yo u need to recharge the battery .
123 Mobile Computing Monitoring main battery power 4 Click Change plan settin gs to choose the plan you want to edit. This screen allows you to change basic settings. 5 Click Change advanced power settings to access settings for battery notification lev els, inte rnal storage driv e power sa ve time, etc.
124 Mobile Computing Using the T OSHIB A eco power plan Using the TOSHIBA eco power plan This computer is equipped w ith the T oshiba eco po wer plan. Operating the computer with th is po wer plan enabled reduces electrical power consumption by slightly lo wering system performance.
125 Mobile Computing Changing the main battery 3 Unplug and remov e any cables connected to the computer , including the A C adaptor . 4 Close the display panel an d turn the computer upside down. 5 Slide the battery release lock to the unlo cked position.
126 Mobile Computing Changing the main battery Inserting a charged battery T o insert a battery: 1 W ipe the terminals of the charge d battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks.
127 Mobile Computing T aking car e of your battery 5 Reconnect any cables that were remov ed in step 3 of “Removing the battery from the computer” on page 124 . 6 Restart the computer . T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life.
128 Mobile Computing T aking car e of your battery Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
129 Mobile Computing Disposing of used batteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main batt ery light flashes amber shortly after you hav e fully rech arged the battery .
130 Mobile Computing T raveling tips T o shiba is dedicated to preservi ng the en vironment by sponsoring Call2Recycle™ , a program of the Rechar geable Battery Recycling Cor por atio n. For more information and for drop-off locations, visit www .rbrc.
131 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system.
132 Exploring Y our Computer’ s Features Explorin g the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, taskbar , notification area, and background pattern.
133 Exploring Y our Computer’ s Features Exploring the desktop ❖ TECHNICAL NOTE: If you delete a large number of files or very large files from the internal storage drive, there may be insufficient space available in the Re cycle Bin to hold these files.
134 Exploring Y our Computer’ s Features Setting up for communications T askbar Each time you open a program, a button associated with that program appears on the taskbar . With some programs, a b utton appears on the taskbar for each document or window you open.
135 Exploring Y our Computer’ s Features Setting up for communications For information on ho w to set up a wireless connection, refer to your wireless networking device documentation or your network administrator . T o enable or disable wireless communication, use the Hot Key Fn + F8 .
136 Exploring Y our Computer’ s Features Setting up for communications 3 Enter the phone number and account information of your Internet connection. 4 Click Connect and let the program dial the number . The computer connect s to the Internet. Connecting a modem to a telephone line (A vailable on certain models.
137 Exploring Y our Computer’ s Features Explori ng audio feat ur es 2 Connect the other end to the RJ-11 wall jack. (Sample Illustration) Connecting to a wall jack Connect the built-in modem only to ordinary analog phone lines. Never connect the built-in modem to a digital line (ISDN).
138 Exploring Y our Computer’ s Features Explor ing audio feat ur es 2 Click Start , All Programs , Acces sories , and then Sound Recorder . (Sample Image) Soun d Recor der scr een 3 Click the Start Recording button. 4 Speak normally into the microp hone.
139 Exploring Y our Computer’ s Features Using the W eb Camera Using the W eb Camera (A vailable on certain models.) Y our computer may come with a built-in W eb Camer a.
140 Exploring Y our Computer’ s Features Using the Memory car d r eader Do not use the Copy Disk function for this type of media. T o copy data from one media to another , use the drag-and-drop feature of the Windows ® operating system. Inserting memory media The follo wing instructions apply to all ty pes of supported media devices.
141 Exploring Y our Computer’ s Features Using the eSA T A/USB combo port 3 Grasp the card and pull it straight out. (Sample Illustration) Removing memory media Do not remove memory media while data is being written or read. Even when the Windows ® message “copying.
142 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help you to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change de fault options.
143 Utilities TOSHIB A Assist ❖ TOSHIB A eco Utility™ ❖ TOSHIB A Service Station ❖ TOSHIB A PC Health Monitor TOSHIBA Assist The TOSHIB A Assist pro vides qui ck access to computer functions and allows you to customize a range of com puter settings.
144 Utilities TOSHIB A Assist Connect The feature a vailable in this category is: ❖ Bluetooth ® Settings (Sample Image) T OSHIBA Assist window – Connect tab.
145 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secure tab.
146 Utilities TOSHIB A Assist Protect & Fix The feature a vailable in this category is: ❖ TOSHIB A PC Diagnostic T ool Utility (Sample Image) T OSHIBA Assist window – Pr otect & F ix tab.
147 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ Mouse Utility ❖ TOSHIB A Hardware Setup (Hardware Settings) ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Access.
148 Utilities TOSHIB A Application Installer TOSHIBA Application Installer The T OSHIB A Application In staller allo ws you to re install the dri vers and applications that were originally bundled with your computer .
149 Utilities Setting passwor ds Setting passwords Setting a password lets you walk aw ay from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can wo rk on your computer again.
150 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to se.
151 Utilities Setting passwor ds 6 Click OK . The supervisor password util ity dialog box appears. 7 Select Able to run HWSetup or Unable to run HWSetup and then Click OK .
152 Utilities Setting passwor ds T o register a passwo rd for the power -on password functions: 1 Click Start , All Programs , TOSH IBA , Utilities , and then TOSHIB A Assist . The TOSHIB A Assist windo w appears. 2 On the left side, click the Secure tab .
153 Utilities TOSHIB A F ace Recognition Utility TOSHIBA Face Recognition Utility Y our co mputer may come with th e TOSHIB A F ace Recognition utility . This utility provides another way to log on to y our computer . For high security purposes, TOSHIBA Face Recognition is not a suitable substitute for Windows ® passwords.
154 Utilities TOSHIB A PC Dia gnostic T ool Utility TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose pro blems with devices in your computer . Refer to the online Help documentatio n within the application for additional help. The TOSHIBA PC Diagnostic T ool u tility may show tests for features you do not have.
155 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Control Panel , Hard ware and Sound , and then under Devices and Printers , click Mouse , or click the Mouse icon in the Op timize tab of TOSHIB A Assist .
156 Utilities TO S H I B A H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the TOSHIBA conf iguration management tool av ailable through th e W indows ® operating system.
157 Utilities TO S H I B A H a rd w a re S e t u p ❖ Display —Allows you to change various default settings for the built-in display When the computer restarts, it remembers the last configuration. If data does not appear on the display you are using after starting in Sleep mode, press Fn + F5 .
158 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 203 ).
159 Utilities TOSHI BA A ccessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot ke y combination with one of the function keys without pressing the two keys simultaneously as is usually required.
160 Utilities TOSHIB A eco Utility™ TOSHIBA eco Utility™ The TOSHIB A eco Utility™ monitors your power savings from using the eco power plan by tracking real-time power consumption and accumulated savings o ver time.
161 Utilities TOSHIB A Service Station TOSHIBA Service Station The TOSHIB A Service Station helps you keep your n e w computer running at its best by notifying you when updated soft ware, firmw are, documentation or other informat ion is av ailable for your computer .
162 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter when using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself.
163 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask .
164 If Something Goes Wrong Pr oblems when you turn on the computer The computer displays the WARNING RESUME F AILURE/Windows Error Recovery – Windows did not shut down successfully message. T o continue, select Start W indows normal ly . This can happen if the computer was put into Sl eep mode and the battery has discharged.
165 If Something Goes Wrong The W indo ws ® operating system is not working If the trickle-charging does not prov e ef fectiv e, visit the T oshiba W eb site at pcsupport.tosh iba.com and see the Support Bulletin Step-Charging the computer ’ s battery (click the Ask Iris ® link and search for the s upport b ullet in by name).
166 If Something Goes Wrong The W indo ws ® operating system is not working ❖ The operating system responds dif ferently from the normal routine. ❖ The screen does not look right. Unless a hardware de vice has failed, problems usually occur when you change the system in some way such as installing a ne w program or adding a device.
167 If Something Goes Wrong The W indo ws ® operating system is not working If your computer is connected to a network, the Startup menu may display different versions of Safe mode. Internet problems My Internet connection is v ery slow . Many f actors contribute to the speed with which you can surf the Internet.
168 If Something Goes Wrong F ixing a pr oblem with De vice Manag er Fixing a problem with Device Manager Device Manager pro vides a way to check and change the configuration of a de vice. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable.
169 If Something Goes Wrong Memory pr oblems Memory problems Incorrectly connected or faulty memory modules may cause errors that seem to be hardware or e ven software r elated. It is worthwhile checking for these firs t: 1 Click Start , and then click the Shut do wn button in the lo wer-right corner of the Start menu.
170 If Something Goes Wrong P ower and the batteries If the A C po wer light stil l does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance. The A C adaptor and power cord/c able work corr ectly , b ut the battery will not charge.
171 If Something Goes Wrong K e yboar d pr oblems Keyboard problems L650 series k eyboard T o capture a print screen of the entire screen, press the Fn + PRTSC key . T o capture only the active window displayed, press Fn + AL T while simultaneously pressing the PR TSC key .
172 If Something Goes Wrong Display pr oblems If you are using th e built-in screen, make sure the display pri ority is not set for an external monitor . T o do this , press Fn and F5 simultaneously (once). If thi s do es not correct the problem, press Fn and F5 simultaneously again to retur n the display priority to its previous setting.
173 If Something Goes Wrong Disk or storag e drive pr oblems The display mode is set to Simultaneous and the exter nal display de vice does not work. Make sure the e xternal monitor is capable of displaying at resolutions of 800 x 600 or higher .
174 If Something Goes Wrong Optical disc drive pr oblems 4 Click the T ools tab. 5 Click the Check now ... button. The Check Disk box appears. 6 Y ou can choose one or both options: ❖ Automatically f ix f ile system er rors ❖ Scan for and attempt reco very of bad sectors 7 Click Start .
175 If Something Goes Wrong Optical disc drive pr oblems Y ou press the disc eject b utton, but the drive tray does not slide out. Make sure the computer is connect ed to a po wer source and turned on. The optical disc dri ve eject mechanism requir es po wer to operate.
176 If Something Goes Wrong Optical disc drive pr oblems While viewing a Blu-ray Disc™ movie the sound is not coming from the computer’ s speakers. Y ou can change the destination of the audio signal in Sound properties in the Control Panel. Blu-ray Disc™ player T echno logy .
177 If Something Goes Wrong Sound system pr oblems Sound system problems No sound is coming from the computer’ s speakers. Adjust the volume control. T ry pressing Fn + Esc to see if volume mute is disabled. Check that the volume control on the computer is turned up.
178 If Something Goes Wrong Modem pr oblems The printer will not print wh at y ou see on the screen. Many programs display information on the screen di f ferently from the way they print it. See if your program has a print previe w mode. This mode lets you see your work exactly as it will print.
179 If Something Goes Wrong W ireless networking pr oblems ❖ V e rify that your computer can det ect access points or routers. If it can detect a W i-Fi ® access point or router then it may be a configuration issue. ❖ V erify that signal strength is good usin g the utility provided with the W i-Fi ® adapter .
180 If Something Goes Wrong D VD and BD operating pr oblems ❖ If you hav e enabled any security provisions (closed system, MA C address filtering, W ired Equivalent Pri v acy [WEP], etc.), check the access point v endor's W eb site for recent firmw are upgrades.
181 If Something Goes Wrong Develop good computing habits A blank scr een appears while watching a D VD-R OM or BD-R OM movie or title. Change the setting for when to tu rn off the display using the following steps: 1 Click Start , Control Panel , System and Security , and then Po wer Options .
182 If Something Goes Wrong Develop good computing habits If you hav e installed your own programs, you should back up these programs as well as your data file s. If something goes wrong that requires you to reformat your inte rnal storage dri ve and start again, reloading all your programs and data files from a backup source will sa ve time.
183 If Something Goes Wrong Develop good computing habits 2 In the left pane, click System protection . The System Protecti on tab of th e System Properties windo w appears. 3 Click Create... 4 In the input field, enter a name that is descripti ve enough to be easily understood in the future, such as “Before installin g Brand X Accounting app.
184 If Something Goes Wrong Develop good computing habits Backing up your data or your entire computer with the Windows ® operating system The most v aluable component of y our computer system is the data you create and store on its internal storage drive.
185 If Something Goes Wrong Develop good computing habits then be able to easily restore the W indows ® operating system to the state it was in prior to the installation, undoing any changes that the installatio n process introduced.
186 If Something Goes Wrong If you need further assistance The eSA T A device is not recognized fr om Sleep or Hibernation mode. A connected eSA T A device may not be recognized if it is connected to the computer’ s eSA T A/USB comb o port (av ailable on certain models) while the computer is in Sleep or Hibernation mode.
187 If Something Goes Wrong Other T oshiba Internet W eb sites T oshiba’ s T echnical Support Web site For technical support, or to stay current on the most recent softw are and hardware options for your computer, and for other product information, be sure to regularly check the T o shiba W eb site at pcsupport.
188 If Something Goes Wrong T oshiba’ s worldwide off ices T oshiba’ s worldwide offices A ustralia T oshiba (Australia) P ty . Limited 84-92 T alav era Road North Ryde NSW 2113 Sydney Australia Canada T o shiba Canada Ltd. 191 McNabb Street Markham, Ontario L3R - 8H2 Canada France T o shiba Systèmes (France) S.
189 If Something Goes Wrong T oshiba’ s worldwide of fices For more information on additional T osh iba worldwide locations, please visit: www .toshi ba.co.jp/ index. htm . United States T o shiba America Information Systems, Inc. 9740 Irvine Boulev ard Irvine, California 92618 United States The Rest of Europe T oshiba Europe (I .
190 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards prov ide a quick way to modif y selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot K ey Cards and Application Cards.
191 Hot Keys /TOSHIBA Ca rds Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off.
192 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 143 .
193 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Using the Application Cards T o launch an application using the Application Cards: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen. (Sample Image) TOSHIB A Car d display 2 Click the “stacked” card on the far right of the display .
194 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 3 The Card Case displays tw o rows of Cards. Cards that appear solid (not tr ansparent) in the bottom ro w are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards .
195 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer .
196 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window .
197 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep mod e” on page 91 .
198 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernatio n mode” on page 89 .
199 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the p o w e r - o n di sp l ay o p t i on s (only th.
200 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode.
201 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the Wi-Fi ® module.
202 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T o uchPad™. For more information on using the T ouchPad, see “Using the T o uchPad™” on page 75 .
203 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution.
204 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot key turns the cursor control ov erlay on and off. Fn + This hot key turns the numer ic ov erlay on and off. Fn + This hot key turns the scroll lock featu re on and off.
205 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our computer ships w ith the correct power su pply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world.
206 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide.
Glossary 207 DIMM Dual Inline Memo ry Module DOS Disk Operating System DPI Dots Per Inch DV D Digital V ersatile (or V ideo) Disc DV D - R O M Digital V ersatile (o r V ideo) Disc Read-Onl y Memory EP.
208 Glossary RO M Read-Only Memory RT C Real-T ime Clock SD Secure Digital SDRAM Synchronous Dynamic Random Access Memory SSD Solid State Driv e TFT Thin Film Transistor USB Univ ersal Serial Bus URL Uniform Resource Locator WA N W ide Area Network www W orld W ide W eb Te r m s The follo wing terms may appear in this user’ s guide.
Glossary 209 B backup — A copy of a file, usually on a remo vable disk, k ept in case the original file is lost or damaged. Basic Input/Outpu t System (BIOS) — See BIOS. baud rate — The speed at which a comm unication de vice, such as a printer or modem , transmits info rmation.
210 Glossary C cache — A section of very fast memory in which frequently used information is duplicated for qu ick access. Accessing data from cache is faster than acces sing it from the computer’ s main memory . See also CPU ca che, L 1 ca che, L2 c ache.
Glossary 211 CPU cache — A section of ver y fast memory residing be tween the CPU and the computer’ s main memory that temporarily stores data and instructions the CPU will need to ex ecute commands and program s. See also cach e, L1 ca che, L 2 ca che.
212 Glossary document — Any file created with an application and, if sa ved to disk, gi ven a name by which it can be retrie ved. See also fil e . double-click — T o press and release the pointing device’ s primary button rapidly twice without moving the pointing device.
Glossary 213 F fil e — A collection of related information, sav ed on disk with a unique name. A file may be a program, information used by a program, or a document. See also docum ent. File Allocation T able (F A T) — The section of a s t o r ag e d riv e that keeps track of the location of stored files .
214 Glossary H DM I ( High-Def inition Multimedia Interface) — An interface used to transmit high quality audio and video signal via a single cable in digital format, providing better picture quality than anal og signal.
Glossary 215 LAN (Local Area Network) — A group of computers or other devices dispersed ov er a relati vely limited area and connected by a communications link that enables any de vice to interact with an y other on the network.
216 Glossary motherboard — The computer’ s main circ uit board th at contains the processor , memory , and other primary componen ts. MS-DOS pr ompt — See system pr ompt. multi-function drive — A D VD dri ve that can read and write to CD and DV D m e d i a .
Glossary 217 password — A unique string of characters entered by a user to v erify his or her identity to the computer or the network. PC Card — A credit-card-sized expansion card designed to increase the capabilities of computers.
218 Glossary Random Access Memory — See RAM. Read-Only Memory — See RO M . reb oo t — See boot , re s t a r t . removable disk — A disk that can be removed from a disk dri ve.
Glossary 219 shortcut — See k eyboar d shortcut . Sleep — A feature of some W indo ws ® operating systems that allo ws you to turn off the computer without exiting your open applications and to continue from where you left off when you turn the computer on again.
220 Glossary W We b — See W orld W ide W eb . Wi- F i ® — A registered trademark term of the W i-Fi Alliance that stands for W ireless Fidelity , and is anot her term for the communication protocol to permit an Ethernet connect ion using wireless communication components.
221 Index A A C adaptor 45 AC p ow e r 116 A C power light 45 accessing network 135 adding memory 50 check total memory 59 optional external devices 50 adequate ventilation cooling fan 44 adjusting T .
222 Index running computer on battery power 114 safety precautions 127 setting notifications 120 battery indicator light 119 BD player general problems 180 BDs using 107 BIOS Setup see TOSHIB A Hardwa.
223 Index disk dri ve corrupted/damaged d ata files 174 missing files /trouble accessing a dri ve 173 running slow 174 display does not look norm al/flickers 172 external monitor not working 173 displ.
224 Index starting again from 91 using 89 hot key disabling or enabling wireless devices 201 display brightness 200 Hibernatio n mode 198 keyboard o verlays 204 Lock (Instant security) 195 Output (Dis.
225 Index M maintaining your battery 128 manual eject hole optical disc driv e 109 memory adding 50 check total memory 59 problem solving 169 remo ving memory module slot cov er 53 Memory card reader .
226 Index power -on password 149 setting 149 setting a supervisor 150 setting a user 151 supervisor password 149 user password 149 port HDMI™ 79 RGB 79 power computer will not start 163 connecting c.
227 Index R real-time clock (R TC) battery 115 recording sounds 137 rec over y checking internal storage dri ve operating status 74 creating recov ery D VDs/media 68 erasing internal storage dri ve 73.
228 Index Setup W izard 49 software program starting 101 starting from Start menu 10 1 sound problem solving 177 sounds recording 137 speakers using external 138 start button 133 starting a program 10.
229 Index user password, setting 151 using a microphone 137 BDs 107 computer lock 95 DV D s 107 exte rnal display de vices 79 Hibernatio n mode 89 hot key to set a power plan 123 Memory card reader 13.
Ein wichtiger Punkt beim Kauf des Geräts Toshiba L640 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toshiba L640 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toshiba L640 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toshiba L640 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toshiba L640 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toshiba L640 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toshiba L640 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toshiba L640. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toshiba L640 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
