Benutzeranleitung / Produktwartung a300/a300d des Produzenten Toshiba
Zur Seite of 201
computers.tosh iba-europe.com User ’ s Manual A300/A300D.
User ’s Manual ii A300/A300D Copyright © 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No p at ent liability is assumed, with respect to the use of the information contained herein.
User ’s Manual iii A300/A300D AMD, the AMD Arrow logo, AMD At hlon, AMD T urion, Radeon, and combinations thereof, A TI Mobilit y Radeon are trademarks of Advanced Micro Devices, Inc. Adobe and Photoshop are eith er regi stered trademarks or trademarks of Adobe Systems Incorporated.
User ’s Manual iv A300/A300D ■ Be sure that noting rests on your AC adapter's pow er cable and that the cable is not located where it can be tripped over or stepped on. ■ Place the AC adapte r in a ventilated area, such as a desk top or on th e floor , when you use it to run the computer or to charge the battery .
User ’s Manual v A300/A300D This product and the original options are design ed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However , TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not pr oduced by TOSHIBA are connected o r implemented.
User ’s Manual vi A300/A300D Modem warning notice Conformity S t atement The equipment has been approved to [Council Decision 98/482/EC - "TBR 21"] for pan-European single terminal connection to the Public Switched T elephone Netwo rk (PSTN).
User ’s Manual vii A300/A300D Following information is only for EU-memb er st ates: The symbol indicates that this product may not be treated as household waste. Please ensu re this product is properly disposed as inappropriate waste handling of this prod uct may cause potential hazards to the en vironment and human health.
User ’s Manual viii A300/A300D GOST Optical disc drive safety instructions Hitach-LG Dat a Storage DVD Super Multi GSA- T40F/GSA-T40N Be sure to check the international prec autions at the end of th is section. ■ The DVD Super Multi dr ive employs a laser system.
User ’s Manual ix A300/A300D Panasonic DVD Super Multi UJ- 870B ■ The DVD Super Multi dr ive employs a laser system. T o ensure proper use of this pro duct, please read thi s instruction manual care fully and retain for future refere nce. Should the unit ever require mainten ance, contact an authorized service location.
User ’s Manual x A300/A300D Pioneer DVD Super Multi DVR- KD08 ■ The DVD Super Multi dr ive employs a laser system. T o ensure proper use of this pro duct, please read thi s instruction manual care fully and retain for future refere nce. Should the unit ever require mainten ance, contact an authorized service location.
User ’s Manual xi A300/A300D TOSHIBA SAMSUNG ST ORAGE TECHNOLOGY CD-RW /DVD-ROM Drive TS-L46 2D ■ The CD-RW/DVD-ROM drive empl oys a las er system. T o ensure proper use of this prod uct, please read th is instruction manual carefully and retain for future reference.
User ’s Manual xii A300/A300D TOSHIBA SAMSUNG ST ORAGE TECHNOLOGY 8x slim DVD W rit able D rive TS-L632H ■ This DVD writable drive employ a laser system to ensure proper use of this product, please read this instruction manual carefully and retainfor future reference.
User ’s Manual xiii A300/A300D TOSHIBA HD DVD-ROM Drive SD-L802B ■ This HD DVD-rom drive employ a lase r system to ensure proper use of this product, please read th is instruction manual carefully and retain for future reference. Should the unit eve r require maintenance, contact an authorized service locati on-see service procedure.
User ’s Manual xiv A300/A300D T OSHIBA HD DVD-RW Drive SD-L912A ■ This dvd writable driv e employ a laser system to ensure proper use of this product, please read th is instruction manual carefully and retain for future reference. Should the unit eve r require maintenance, contact an authorized service locati on-see service procedure.
User ’s Manual xv A300/A300D International Precautions CAUTION: This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT ." T o use this mod el properly , read the instruction manual carefully and keep thi s manual for your future referenc e.
User ’s Manual xvi A300/A300D Import ant Notice Copyrighted works incl uding, but not lim ited to music, vi deo, computer program, databases are protected by copyright laws.
User ’s Manual xvii A300/A300D General Precautions TOSHIBA computers are designed to optimize safety , minimize strain and withstand the rigors of portability . Ho wever , certain precautions should be observed to further reduce the risk of personal injury or damag e to the computer .
User ’s Manual xviii A300/A300D Heat injury ■ Avoid prolonged physical contact with the computer . If the computer is used for long periods, its surface can become very warm.
User ’s Manual xix A300/A300D T able of Content s Chapter 1 Introduction Equipment ch ecklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User ’s Manual xx A300/A300D Chapter 4 Operating Basics Using the T ouchPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Using the fingerprint sensor (op tional) . . . . . . . . . . . . . . . . . . . . . . . 4-2 USB Sleep and Charge functio n .
User ’s Manual xxi A300/A300D Chapter 8 Optional Devices ExpressCard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 SD/SDHC/MMC/MEMOR Y STIC K/MEMORY STICK PRO/ xD Memory cards . . . . . . . . . . . . .
User ’s Manual xxii A300/A300D Preface Congratulations on your purch ase of the TOSHIBA A300/A300D computer . This powerful notebook computer provides excel lent expansion capability , including multimedia devices, and it is design ed to provide years of reliable, high-performance computing.
User ’s Manual xxiii A300/A300D Chapter 5, The Keyboa rd , describes special keyboa rd functions including the keypad ov erlay and hot keys. Chapter 6, Power an d Power-Up Modes , gives details on the computer's power resources and battery save modes.
User ’s Manual xxiv A300/A300D Display Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below .
User ’s Manual 1-1 Introduction Chapter 1 Introduction This chapter provides an equipment checkli st, and it identifies the computer's features, options and accessories. Equipment checklist Carefully unpack your computer . Save the box and packing materia ls for future use.
User ’s Manual 1-2 Introduction ■ TOSHIBA Disc Creator ■ TOSHIBA Face Recognition* ■ TOSHIBA Acoustic Silencer ■ Ulead MovieFactory ® for TOSHIBA* ■ Presto! BizCard 5* ■ Online Manual* * Indicates software that is preinstalled dependant on the model purchased.
User ’s Manual 1-3 Introduction Main Memory Disclaimer Part of the main system memory may be used by the graphics system fo r graphics performance and therefore reduce the amount of main system memory available for other computing activities.
User ’s Manual 1-4 Introduction Power Video RAM Depending on the model you purcha sed. Mobile Intel ® GM96 5 Express Chipset/Mobile Intel ® GL960 Express Chipset model: Video RAM capacity shares with main memory , and the proportion d epends on Dynamic Video Memory T echnology .
User ’s Manual 1-5 Introduction Disks Hard disk Drive Depends on the model you purchased. ■ 120 GB ■ 160 GB ■ 200 GB ■ 250 GB ■ 320 GB ■ 400 GB ■ 500 GB Other hard disk d rives may be introduce d in the future. Computers in this series are conf igured with an optical media drive.
User ’s Manual 1-6 Introduction DVD Super Multi drive (Supporting DVD±R DL) Some models are equip ped with a full -size DVD Super Multi drive module that lets you record data to rewritable CDs/DVDs as well as run either 12cm (4.72") or 8cm (3.
User ’s Manual 1-7 Introduction HD DVD-ROM Some models are equip ped with a full -size HD DVD-ROM drive module that lets you run CDs/DVDs without using an adaptor .
User ’s Manual 1-8 Introduction HD DVD-RW drive Some models are equip ped with a full -size HD DVD-RW drive module that lets you run CDs/DVDs without using an adaptor .
User ’s Manual 1-9 Introduction Display The computer's LCD panel su pports high-resolution video graphics. The screen can be set at a wide range of vie wing angles for maximum co mfort and readability . Keyboard Pointing Device Ports Built-In 15.
User ’s Manual 1-10 Introduction Slots Multimedia Communications ExpressCard The ExpressCard expansion slot can accommodate two standard module formats; an ExpressCard/34 module and an ExpressCard/54 module. An ExpressCard module is a small add- in card technology based on the PCI Express and Universal Serial Bus (USB) interfaces.
User ’s Manual 1-1 1 Introduction Security Wire les s LAN Where present, it suppor ts the A,B,G and draft N standards but it is compatible with other LAN systems based on Direct Sequence S pread S pectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.
User ’s Manual 1-12 Introduction Sp ecial features The following features are eithe r un ique to TOSHIBA computers or are advanced features, which make the co mputer more convenient to use. Hot Keys Key combinations let you quickly modify the system configuration dire ctly from the keyboard without running a system configuration program.
User ’s Manual 1-13 Introduction T OSHIBA V alue Added Package This section describes the TOSHIBA Component features pre-installed on the computer . Low Battery Automatic Hibernation *1 When battery pow er is exhausted to th e point that computer operation cannot b e continued, the system automatically ent ers Hibernation Mode and shuts down.
User ’s Manual 1-14 Introduction Utilities and Applications This section describes pre-installed utilities an d tells how to start them. For details on operations, refer to eac h utility’s online manual, help files or readme.
User ’s Manual 1-15 Introduction TOSHI BA DVD-RA M Utility TOSHIBA DVD-RAM Utility has a Physical Format function and Write-Protect function to DVD-RAM.
User ’s Manual 1-16 Introduction TOSHIBA HD DVD Player The HD DVD Player is used to play HD DVD Videos. It has an on-screen interface and functions. (Provided with some models.) TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy control of communication devices and network connections.
User ’s Manual 1-17 Introduction Options Y ou can add a numbe r of options to make your computer even more powerful and convenient to use. Refer to Chapter 8 Optional Devices , for details. The following opti ons are available: Windows Mobility Center This section describe s the Windows Mobility Center .
User ’s Manual 2-1 The Grand T our Chapter 2 The Grand T our This chapter identifies the vari ous components of your computer . Become familiar with each component before yo u operate the computer . Front with the display closed The following figure shows the computer's front with its display panel in the closed positi on.
User ’s Manual 2-2 The Grand T our Power LED The Power indicator glows blue when the computer is on. If you select Sleep Mode from T urn Off Computer , this indicato r flashes orange (one second on, two seconds off) while the computer enters Sleep Mode.
User ’s Manual 2-3 The Grand T our Lef t side The following figure shows the computer's left side. The left side of the computer Cooling V ents External Monitor Port Universal Serial Bus (USB 2.
User ’s Manual 2-4 The Grand T our Right side The following figure shows the computer's righ t side. The right side of the computer * The figure shows Modem Jack. i.LINK (IEEE1394a) Port This port allows you to connect an extern al device, such as a digital video camera, for highspeed data transfer .
User ’s Manual 2-5 The Grand T our Backside The following figure shows the computer's back panel. The backside of the computer Underside The following figure shows the undersi de of the computer . Make sure the display is closed before turning over your computer .
User ’s Manual 2-6 The Grand T our Front with the display op en This section shows the front of the co mputer with the display open. Re fer to the appropriate illustration fo r details. T o open the display , lift the front of the display . Position the displ ay at a comfortable viewing angle.
User ’s Manual 2-7 The Grand T our Please handle your computer carefully to avoi d scratching or damaging the surface. Speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, gene rated by the system.
User ’s Manual 2-8 The Grand T our Optical Disc Drive An A T API interface controller is used for optical disc op eration. When the computer is accessing a optical disc, an indica tor on the drive glow s.
User ’s Manual 2-9 The Grand T our About HD DVD This section describes the feature s and use of HD DVD and HD DVD Media. Summary HD DVD allows users to en joy video, concerts and other packaged content by taking advantage of its large amoun t of storage space and high-quality audio and video.
User ’s Manual 2-10 The Grand T our ■ Dolby Digital audio enhancements are only supported by Microsoft ® Windows ® operating systems. C ontent with high samp le rates of 48kHz or more are downsampled when output through either the built-in speakers or headphone jack.
User ’s Manual 2-1 1 The Grand T our HD DVD-ROM drive The full-size HD DVD-ROM drive module lets you run either 12 cm (4.72") HD DVDs,12 cm (4.7 2") or 8 cm (3.15") CD/DV Ds without using an adaptor . The read speed i s slower at the centre of a disc and faster at the outer edge.
User ’s Manual 2-12 The Grand T our HD DVD-RW drive The full-size HD DVD-RW drive module lets you run either 12 cm (4.72") HD DVDs,12 cm (4.7 2") or 8 cm (3.15") CD/DV Ds without using an adaptor . AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer .
User ’s Manual 2-13 The Grand T our The AC adaptor ■ Use only the AC adaptor that came wi th the computer or an equivalent optional adaptor . Use of the wr ong adaptor could damage your computer . TOSHIBA assumes no liability for any damage in such case.
User ’s Manual 2-14 The Grand T our Remote controller (optional) A remote controller , which is provided with some models, enables you to perform some functio ns of your computer from a di stant locati on. Y ou can use your remote controll er wit h Media Center to play CDs, DVDs and videos, to vie w pictures.
User ’s Manual 2-15 The Grand T our Power S t arts or terminate the operating system.This button functions like the power button of your computer . By default, the Sleep mode is equivalent to the power off state of your computer .
User ’s Manual 2-16 The Grand T our Using the rem ote contro ller Some computers include a remote contro l unit, which allo ws you to control some of your computer ’s functions from a distant location. Operational range of the remote controller Point the remote controller at y our computer and press a button.
User ’s Manual 2-17 The Grand T our Operational range of the remote contr oller Inst alling/Rem oving batteries Be sure to install the provided CR2016 type batteries before usin g the remote controller . Th e procedures for installing and removing the batteries vary depending on the type of the remote controller .
User ’s Manual 2-18 The Grand T our T ype of battery that can be used for the remote controller When the provided batteries run down , please replace them with ad equate ones. CR2016 type battery is available. Other types or battery should not be used.
User ’s Manual 2-19 The Grand T our 2. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it fo rward to fit into the battery case. Inserting the batteries 3. Close the battery cove r . Close the cover securely until it clicks.
User ’s Manual 2-20 The Grand T our 3. Insert the battery in place. Be sure to place the batteries w ith correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case. 4. Close the battery cove r . Close the cover securely until it clicks.
User ’s Manual 3-1 Getting S tarted Chapter 3 Getting S t arted This chapter provides basic information to get you started using your computer . It cove rs the following topics: ■ Installing the b.
User ’s Manual 3-2 Getting S tarted 4. Secure the Battery Pack Lock to ensure the battery is locked into place. Later , when you want to remove the battery you must disengage this lock first. Securing the battery pack Connecting the AC adaptor Attach the AC adaptor when you need to cha rge the battery or you want to operate from AC power .
User ’s Manual 3-3 Getting S tarted 1. Connect the power cord to the AC adaptor . Connecting the power cord to the AC a daptor 2. Connect the AC adaptor's DC output pl ug to the DC IN 19V jack on the back of the computer . Connecting the adaptor to the computer 3.
User ’s Manual 3-4 Getting S tarted Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Lift the panel up and adjust it to the best viewing an gle for you. Opening the display T urning on the power This section describes how to turn on the power .
User ’s Manual 3-5 Getting S tarted T urning on the pow er Windows V ista™ setup When you turn on the power for the firs t time , the computer's initial screen is the Microsoft ® Windo ws Vist a™ S tartup Screen Logo. Follow the on-scre en directions.
User ’s Manual 3-6 Getting S tarted Sleep Mode If you have to interrupt your work, y ou can turn off the power without exiting from your software. Data is maintai ned in the computer's main memory . When you turn on the power again, you can continue wo rking right where you left off.
User ’s Manual 3-7 Getting S tarted ■ Click , click power button located in the power management buttons , or click arrow button and select Sleep from the menu. ■ Close the display panel. This feature mu st be enabled. Please refer to the Power Options (to access it, click Control Pa nel System and Maintenance Power Optio ns ).
User ’s Manual 3-8 Getting S tarted ■ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature . ■ Y o u can use the panel power off feature. S tarting Hibernation Mode T o enter Hibernation Mode, follow the steps below .
User ’s Manual 3-9 Getting S tarted There are three ways to re set the computer system: 1. Click then click the arrow icon located in the power mana gement button , and select Rest art from the pull down menu. 2. Press Ctrl + Alt + Del , then select Rest art from the Shut down options.
User ’s Manual 3-10 Getting S tarted Restoring the pre-in sta lled Sof tware Depending on the model you purchased, different ways for restoring the pre-installed software are of fered: ■ Creating optical Recovery Discs ■ Restoring the pre-installed software from your created Reco very Discs.
User ’s Manual 3-1 1 Getting S tarted 6. After Recovery Disc Creator start s, select the type of media and the title you wish to copy , and then click the Create button.
User ’s Manual 3-12 Getting S tarted 1. T urn of f the computer . 2. T urn on the computer a nd when the TOSHIBA screen appea rs repeatedly press the F8 key . 3. The Advanced Boot Options menu will be displayed. Use the arrow keys to select Rep air Y our Comput er and press ENTER .
User ’s Manual 4-1 Operating Basics Chapter 4 Operating Basics This chapter gives information on basic operation s including using the T ouchPad, fingerprint sensor (optional ), USB Sleep and Charge function, web camera (opti onal), internal microphone (optional), optical media drives, sound system, modem, Wireless LA N and LAN.
User ’s Manual 4-2 Operating Basics For some functions, you ca n tap the T ouchPad instead of pressing a control button. Using the fingerprin t sensor (optional) Some models in the serie s have a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.
User ’s Manual 4-3 Operating Basics Slide the finger over the recognition sensor Point s to note abo ut the fingerprint sensor Failure to follo w these guidelines might result in (1 ) damage to the se nsor or cause sensor failure, (2) finger reco gnition problems, or lower finger recognition success rate.
User ’s Manual 4-4 Operating Basics ■ W ash and dry your hands thoroughly . ■ Remove static electricity from y our fingers by touching any metal surface. S tatic electricity is a common cause of sensor failures, especially when the weather is dry .
User ’s Manual 4-5 Operating Basics Fingerprint sensor limit ations ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. ■ A warning message will be displayed when recognition is abnormal or recognition is not successf ul wit hin a fixed durati on.
User ’s Manual 4-6 Operating Basics 3. The Control Center screen is displayed. Click the non-enrolled fi nger icon above the finger . 4. The Fingerprint Enrollment screen is displayed . Confirm the message and click Next . 5. The Scanning Practice screen is displayed.
User ’s Manual 4-7 Operating Basics Fingerprint system boot authenticatio n General The fingerprint auth entication system can be used to replace the keyboard based User Password authentic ation system when booting up.
User ’s Manual 4-8 Operating Basics Fingerprint Single Sig n-On feature General This is a feature that allows the us er to comple te the authentication for both the User Password (and optionally , the HD D user and Supervi sor passwords) and logging on to Windows using only one fingerprint authentication when boo ting up.
User ’s Manual 4-9 Operating Basics Y ou can use the " USB Sleep and Charge function" to charge certain USB- compatible external devices such as mobile phones or portable digital music players.
User ’s Manual 4-10 Operating Basics Using the Web Camera ( optional ) Some models in this seri es are equipped with a webcam utility , which ca n capture still and video images.
User ’s Manual 4-1 1 Operating Basics Using the micro phone (optional) Some models in this seri es are equipped with a built-in microph one that can be used to record monaural sounds into your applica tions. It can also be used to issue voice commands to applications that support such functions.
User ’s Manual 4-12 Operating Basics Using the optical disc drive Operation is the same for all optical media drives. The full-size drive provides high-performance execut ion of C D/DVD-based programs. Y ou can run either 12 cm (4.72") or 8 cm (3.
User ’s Manual 4-13 Operating Basics b. Pressing the eject button will not open the drawer when the disc drive's power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the rig ht of the eject button.
User ’s Manual 4-14 Operating Basics 3. Place the disc, label sid e up, in the drawe r . Inserting a disc 4. Press gently at the centre of the disc until you feel it click into place. The disc should lie b elow the top of the spin dle, flush with the spindle base.
User ’s Manual 4-15 Operating Basics Closing the disc drawer Removing discs T o remove the disc, fo llow the steps below . 1. T o pop the drawer partially open, pr ess the eject button. Gently pull the drawer out until it i s fully opened. 2. The disc extends slightly over the sides of the drawer so you can hold it.
User ’s Manual 4-16 Operating Basics Removing a disc 3. Push the centre of the drawer to cl ose it. Press gently until it locks into place. W riting CD/DVD with the DVD Super Mu lti drive or HD DVD-.
User ’s Manual 4-17 Operating Basics Before writing or rew riting ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD- R/RW and DVD-R/+R/-RW/+RW/-RAM discs. However , in no event does TOSHIBA guarantee the operation, quality or performance of any disc.
User ’s Manual 4-18 Operating Basics ■ We can support only Format1 of DV D-R DL. Therefore you can not do the additional writing. If your data is under 4.7 GB, we suggest to use DVD-R (SL) media. ■ Y ou can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a ca rtridge.
User ’s Manual 4-19 Operating Basics When w riting or re writing Please observe/consider the followi ng when you write or rewrite to a CD-R/-RW , DVD-R/-RW/-R AM or DVD+R/+RW disc. ■ Do not perform any of the following actions when writing or rewriting: ■ Change users in the Windows ® Vista operating system.
User ’s Manual 4-20 Operating Basics W riti ng CDs/DVDs/HD DVDs on HD DVD-RW drive Y ou can use the HD DVD-RW drive to write data to either CD-R or CD-R W , DVD-R, DVD-R (Dual Layer), DVD-RW , DVD+R, DVD+R (Double Layer), DVD-RAM, HD DVD-R, HD DVD-R(Dual layer) discs.
User ’s Manual 4-21 Operating Basics ■ Any change or loss of the reco rded contents of CD-R, CD-RW , DVD-R,DVD-R (Dual Layer), DVD-RW , DVD +R, DVD+R (Double Layer),DVD+RW , DVD-RAM.
User ’s Manual 4-22 Operating Basics ■ If the disc is poor in quality , or is dirty or damaged, wr itin g or rewriting errors may be noted - ensure that you check a ll discs for dirt or damage before you use them.
User ’s Manual 4-23 Operating Basics ■ In writing to DVD-R, DVD-R (Dua l Layer), DVD-RW , DVD+R, DVD+R (Double Layer), DVD+RW , DVD-RAM, HD DVD-R, HD DVD-R(Dual Layer) or HD DVD-RW media, some sp ace is required for file management, so you may not be able to write to the full capacity of the disc.
User ’s Manual 4-24 Operating Basics ■ Do not perform any of the following actions: ■ Change users in the Windows VistaTM operating system. ■ Operate the computer for any other function, including such tasks as using a mouse or T ouch Pad, or closing/opening the display panel.
User ’s Manual 4-25 Operating Basics ■ Y o u cannot back up CD-ROM, CD-R or CD-RW media to DVD+R, DVD+R (Double Layer) or DVD+RW media using the "Disc Backup" function of T OSHIBA Disc Creator .
User ’s Manual 4-26 Operating Basics How to learn more about TOSHIBA Disc Creator Please refer to the Help files for additional TOSHIBA Disc Creator information.
User ’s Manual 4-27 Operating Basics Simplified steps for making a DVD-Video from adding video source: 1. Click All Programs DVD MovieFactory for TOSHIBA Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory .
User ’s Manual 4-28 Operating Basics 2. Before recording the video to DVD ■ When you record DVD disc, pleas e use only discs recommended by the Drive manu facturer . ■ Do not set the workin g drive to a slow device like a USB1.1 hard disk drive or it will fail to write DVD.
User ’s Manual 4-29 Operating Basics 3. Do not write on, apply a sticker to, or otherwi se mar the surface of the CD/DVD/HD DVD that contains data. 4. Hold the CD/DVD/HD DVD by its outside edge or the edge on the centre hole. Fingerprints on the su rface can prevent the drive from properly reading data.
User ’s Manual 4-30 Operating Basics 3. Select a region from the region menu or a telephony location from the sub-menu. ■ When you click a reg ion it becomes the modem's region selection, and the New Location for telepho ny will be set automatically .
User ’s Manual 4-31 Operating Basics Connecting T o connect the modem cable, follow th e steps below . 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telep hone jack. Connecting the internal modem Disconnecting T o disconnect the inte rnal modem cable, follow the steps below .
User ’s Manual 4-32 Operating Basics Using the FM tuner (optional) The availability of this feature i s depending on the model you purchased. 1. Plug the FM tuner antenna i nto the FM Anten na Jack. 2. Select Star t All Progra ms FM T u ner Utility to start FM s oftware.
User ’s Manual 4-33 Operating Basics Wireless LAN Where present, it supports the A,B, G and draft N standards but it is compatible with other LAN systems based on Direct Sequence S pre ad S pectrum/Orthogonal Frequency Division Mul tiplexing radio technolo gy that complies with IEEE802.
User ’s Manual 4-34 Operating Basics Release Notes related to th e Bluetooth S tack for Wi ndows by TOSHIBA 1. Fax application software: Regarding F AX application software, there are some software that you cannot use on this Bluetoo th S t ack.
User ’s Manual 4-35 Operating Basics LAN The computer has built-in suppo rt for Fast Ethernet LAN or Giga bit Ehternet LAN (depends on the model you purchased). LAN cable types If you are using Fast Ethernet LAN (100 mega bits per second, 100BASE-TX), be sure to connect with a CA T5 cable or higher .
User ’s Manual 4-36 Operating Basics Disconnecting LAN cable T o disconnect the LAN cable, follow the steps below . 1. Pinch the lever on the connector in the computer's LAN jack and pull out the connector . 2. Disconnect the cable from the LAN hub in the same manner .
User ’s Manual 4-37 Operating Basics ■ Never transpo rt your comput er with Expre ssCards inst alled. T his could cause damage to your computer and/or ExpressCard, resu lting in product failure. ■ Use the carrying case when transportin g the computer .
User ’s Manual 5-1 The Keyboard Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functi ons can be executed on the computer .
User ’s Manual 5-2 The Keyboard F1 ... F12 functio n keys The function keys (not to be confused with Fn ) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called functi on keys because they execute programmed functions when p ressed.
User ’s Manual 5-3 The Keyboard Press Fn + F1 1 to access the integrated ke yp ad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys. Refer to the Keypad overlay section in this chapter for more information on how to operate these keys.
User ’s Manual 5-4 The Keyboard Brightness (increase): Turns the monitor brightness up. Wireless: Switches the active wireless devices if the wireless communication switch is on. T ouchPad: Enables o r disables the T ouchPad function. Enable Keypad: Enables or disables the Key Pad function.
User ’s Manual 5-5 The Keyboard Fn Stick y key (Depends on the model you pu rchased) Y ou can use the TOSHIBA Accessi bility Utility to make the Fn key sticky , that is, you can press it once, release it, and then press an " F number " key .
User ’s Manual 5-6 The Keyboard Numeric mode T o turn on the Numeric mode, press Fn + F1 1 . Now try numeric data entry using the keys in the following figure.
User ’s Manual 5-7 The Keyboard Generating ASCII charact ers Not all ASCII characters can be generated using norma l keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay o n: 1. Hold down Alt . 2. Using the overlay keys, type the ASCII code.
User ’s Manual 6-1 Power and Power-Up Modes Chapter 6 Power and Power-Up Modes The computer's power resources in cl ude the AC adaptor a nd internal batteries. This chapter gives details on making the most effective use of these resources including charging and ch anging batteries, tips for saving battery power , and power up modes.
User ’s Manual 6-2 Power and Power-Up Modes Power indica tors As shown in the above table, the Battery and Power indicators on the system indicator panel alert you to th e computer ’s operating cap ability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery pack.
User ’s Manual 6-3 Power and Power-Up Modes Battery types The computer has the following ba tteries: ■ Battery pack (3cell, 6cell, or 9cell depen ding on the model.
User ’s Manual 6-4 Power and Power-Up Modes Real T ime Clock battery The Real Time Clock (RTC) battery provides power fo r the internal real time clock and calendar . It also ma intains the system configuration. If the R TC battery becomes complete ly discharged, the system loses this data and the real time clock and calendar stop working.
User ’s Manual 6-5 Power and Power-Up Modes Care and use of the battery p ack The battery pack is a vital component of po rtable computing. T aking proper care of it will help ensu re longer ope rating time on battery power as well as a longer life for your battery pack.
User ’s Manual 6-6 Power and Power-Up Modes 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack’ s internal protective device will fail, causing it to overheat, explode, ignite or lea k caustic liquids possib ly resulting in death or serious injury .
User ’s Manual 6-7 Power and Power-Up Modes 6. Be sure to monitor the remaining battery power . If the battery p ack and real time clock battery discharge completely , Sleep Mode will not function and data in memory will be lost. Also, the co mputer might register an inco rrect time and date.
User ’s Manual 6-8 Power and Power-Up Modes Battery charging notice The battery may not charge right away under the following conditions: ■ The battery is extremely hot or cold.
User ’s Manual 6-9 Power and Power-Up Modes Maximizing battery op erating time A battery’s usefulness depends on how long it can supply power on a single charge.
User ’s Manual 6-10 Power and Power-Up Modes 3. Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the Battery indicator flashes or there is some other warning to indicate a low battery , go to step 4.
User ’s Manual 6-1 1 Power and Power-Up Modes 5. Slide and hold the battery release latch to free the battery pack after moving the battery p ack lock into its unlock position - then slide the battery pack out of the computer . Releasing the battery pack Inst alling the batte ry p ack T o install a battery , follow the steps below .
User ’s Manual 6-12 Power and Power-Up Modes St arting the computer by p assword T o start up the computer with the user password, follow these step s: 1. T urn on the powe r as describ ed in Chapte r 3, Getting St arted . The following message app ears: 2.
User ’s Manual 6-13 Power and Power-Up Modes Panel power off/on Y ou can set up your computer so that power tu rns off automatical ly when you close the display panel. When you open the panel, power turns on in Sleep Mode or Hibernation Mode but not in boot mode.
User ’s Manual 7-1 HW Setu p Chapter 7 HW Setup This chapter explains how to us e TOSHIBA HW Setup program to configure your computer . T OSHIBA HW Setup lets you configure settings for General, Password, Display , Boot Priority , Keyboard, LAN, and USB.
User ’s Manual 7-2 HW Setu p Password This tab allows you to set or reset the user p assword for power on. User Password Lets you register a new password or un-register an existing password. Owner S tring This blank field is used to display a message when the password field is displayed on startup.
User ’s Manual 7-3 HW Setu p Keyboard Wa ke-up on Key board When this feature is enabl ed and the computer is in Sleep Mode, you can turn on the computer by pressing any key . It is effective only for the internal keyboard and only when the computer is in Sleep Mode.
User ’s Manual 8-1 Optional Devices Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility . This chapter describ es connection or installation o.
User ’s Manual 8-2 Optional Devices Inserting an ExpressCa rd One ExpressCard connector is located on the righ t side of the computer . The computer's hot-install feature le ts you install ExpressCard while the computer's power is on. T o install an ExpressC ard, follow the steps below .
User ’s Manual 8-3 Optional Devices Removing the ExpressCard SD/SDHC/MMC/ MEMOR Y STIC K/MEMOR Y STICK PRO/xD Memory cards The computer is equi pped with a mul tip le digital media card slot that can accommodate SD/SDHC/MMC/MEMORY STICK/MEMORY STICK PRO/xD memory cards.
User ’s Manual 8-4 Optional Devices Inst alling a mem ory card T o install a memory card: 1. Insert the memory card. 2. Press gently to ensure a firm connection. Inserting a memory card Do not insert Me mory S tick Duo/PRO Duo into the slot. Data may be lost or damaged if you use any card other than those supporte d.
User ’s Manual 8-5 Optional Devices Removing a mem ory card T o remove a memory card, follow the step s below: 1. Click the Safely Remove Hardware icon on the T askba r .
User ’s Manual 8-6 Optional Devices 5. Do not twist or bend memory cards. 6. Do not expose memory cards to liquids or store in humid areas or lay media close to containers of liquid. 7. After using a memory card , return it to its case. 8. Do not touch th e meta l part or expose i t to liquids or let it get dirty .
User ’s Manual 8-7 Optional Devices Removing the memory module cover 6. Lift one side of the insulator sheet and fit the module's connectors into the computer's connectors at a bou t a 45 degree angle. Press the module carefully to ensur e a firm connection.
User ’s Manual 8-8 Optional Devices Points to note about memory module error If you install a memory module that is not compatible with the computer , the Power indicator will flash (on for 0.5 seconds, off for 0.5 seconds) in the following ways: ■ If there is only an error in Slot A: repeatedly flashes orange twi ce, then blue.
User ’s Manual 8-9 Optional Devices Removing the memory module 6. Seat the cover and secure it with screws and replace the battery pack. Additional battery p ack Y ou can increase the portability of t he computer with additional battery packs.
User ’s Manual 8-10 Optional Devices When you turn on the power , the Windows ® Bootup screen (Windows ® Logo) appears on the display device. However , the Windows ® Desktop appears on a di splay device that you used last time to shut down your PC, if the display device exists when you turn on the power .
User ’s Manual 8-1 1 Optional Devices 1. Plug one end of the HDMI cable into the HDMI port of the HDMI device. Connecting a HDMI cable 2. Plug the other end of the HDMI cable into the HDMI out port on your computer .
User ’s Manual 8-12 Optional Devices T o set the audio device to use internal speaker , follow the steps below . 1. Click S tart. 2. Click Control Panel. 3. Click Hardware and Sound. 4. Click Sound. 5. Click S peakers. 6. Click the Set Default Device button.
User ’s Manual 8-13 Optional Devices Connecting 1. Make sure the connectors are pr operly aligned and plug the i.LINK (IEEE1394) cable into the computer . 2. Plug the other end of the cable into the device. Note the following when you use i .LINK: a.
User ’s Manual 8-14 Optional Devices Security lock Security locks enable you to anchor yo u r computer to a desk or other heavy object to help prevent unauthorized removal of the computer . The computer has a se curity lock slot on the left side. Attach one end of the cable to a desk and the other end to th e security lock slot.
User ’s Manual 9-1 T roubleshooting Chapter 9 T roubleshooting TOSHIBA designed the computer for dur ability . However , should prob lems occur , following the p rocedures in this cha pter can help to de termine the cause. All readers should become familiar with this chapter .
User ’s Manual 9-2 T roubleshooting ■ Inspect all connecting cables for loose wires and all connectors for loose pins. ■ Check that your CD/DVD/CD-RW/H D DVD-R is correctly inserted. Make notes of your observations and keep them in a permanent error log.
User ’s Manual 9-3 T roubleshooting Hardware and system checklist This section discusses problems ca used by your computer's hardware or attached peripherals.
User ’s Manual 9-4 T roubleshooting Power When the computer is not plugge d into an AC outlet, the battery pack is the primary power source. However , your computer ha s a number of other power resources, including an intelligent powe r supply and a Real T ime Clock battery .
User ’s Manual 9-5 T roubleshooting Battery If you suspect a problem with the battery , check the Battery indicator . For information on in dicator and battery opera tion refer to Cha pter 6, Power and Power-Up Modes . Problem Procedure Battery doesn't power the computer The battery may be discharged .
User ’s Manual 9-6 T roubleshooting Disposing of PC and PC ba tteries ■ Discard this PC in accordance with applicable la ws and regulations. For further informati on, cont act your lo cal government .
User ’s Manual 9-7 T roubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard .
User ’s Manual 9-8 T roubleshooting Hard disk drive DVD Super Multi drive (Supporting DV D±R DL) For more inform ation, refer to Chapter 4, Operating Basics . Problem Procedure Computer does not boot from hard disk drive There may be a p roblem with you r operating system files.
User ’s Manual 9-9 T roubleshooting Some CD/DVDs run correctly , but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software's needs. Check the CD/DVD documentation.
User ’s Manual 9-10 T roubleshooting HD DVD-ROM drive For more inform ation, refer to Chapter 4, Operating Basics . Problem Procedure Y ou cann ot access a CD/DVD/HD DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place.
User ’s Manual 9-1 1 T roubleshooting Some CD/DVDs run correctly , but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation.
User ’s Manual 9-12 T roubleshooting HD DVD-RW drive For more inform ation, refer to Chapter 4, Operating Basics . Problem Procedure Y ou cann ot access a CD/DVD/HD DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place.
User ’s Manual 9-13 T roubleshooting Some CD/DVD/HD DVD run correctly , but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD/HD DVD documentation.
User ’s Manual 9-14 T roubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. T ouchPad Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy .
User ’s Manual 9-15 T roubleshooting USB mouse USB Also refer to your USB device’s document ation. Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy . If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it.
User ’s Manual 9-16 T roubleshooting USB Sleep and Charge functi on Problem Procedure I cannot use the "U SB Sleep and Char ge function". The setting of "USB Sleep and Ch arge function" may be [Disabled]. Change the setting to [Enabled] in the HW Setu p.
User ’s Manual 9-17 T roubleshooting Memory exp ansion Refer also to Chapter 8, Optional Devices , for information on installing memory modules. External devices connected to the compatible ports do not work when connected to a compatible port.
User ’s Manual 9-18 T roubleshooting Sound system Refer also to documentation fo r your audio devices. Monitor Refer also to Chapter 8, Optional Devices , and to your monitor ’s documentation. Modem Problem Procedure No sound is heard Check the software volume settings.
User ’s Manual 9-19 T roubleshooting LAN Wireless LAN If the following procedures do not re store LAN access, consult your LAN administrator . For more information on wireless communication, refer to Chapter 4, Operating Basics .
User ’s Manual 9-20 T roubleshooting Fingerprint sensor ExpressCard Refer also to Chapter 8, Optional Devices . Problem Procedure Reading of the fingerpr int was not successful Please try again using t he correct posture. Re fer to Using the finge rprint sensor (optional) in Chapter 4, Operating Basics .
User ’s Manual 9-21 T roubleshooting T OSHIBA support If you require any additional help using your compu ter or if you are having problems operating the computer, you may need to cont act TOSHIBA for additional techni cal assistance.
User ’s Manual A-1 S pecifications Appendix A S pecifications This appendix summarizes the computer's technical specifi cations. Environment al Req uirement s Power Requirements Built-in Mod em.
User ’s Manual A-2 S pecifications Communication specificatio ns Communication System Data: Full duplex Fax: Half duplex Communication protocol Data ITU-T -Rec (Former CCITT) Bell Fax: ITU-T -Rec (Former CCITT) V .21/V .22/V .22bis/V . 32/ V .32bis/V .
User ’s Manual B-1 Display Controller and Modes Appendix B Display Controller and Modes Display controller The display controller in terprets software commands into hardware commands that turn particular pels on or o ff.
User ’s Manual B-2 Display Controller and Modes V ideo Modes The computer supports video modes defined in the table below . If your applica-tion offers a selection of mo de numbers that do not match the numbers on the table, select a mode based on, resolution, numbe r of colors and refresh rates.
User ’s Manual C-1 Wireless LAN Appendix C Wireless LAN Card S pecifications Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the produ ct was purchased ■ T ype of product Wireless communication is often subject to local radio regulations.
User ’s Manual C-2 Wireless LAN The range of the wireless signal is relate d to the transmit rate of the wireless com municatio n de vice. Communications at a lower transmission rate may travel larger distances.
User ’s Manual C-3 Wireless LAN When installing Wireless LAN card s, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Ac cess Point.
User ’s Manual D-1 AC Power Cord and Connectors Appendix D AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used.
User ’s Manual D-2 AC Power Cord and Connectors The following illustra tions show the pl ug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Eu rope.
User ’s Manual E-1 Legal Footnotes Appendix E Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. Non-applicable Icons Certain computer chassis are design ed to accommodate all possible configurations for an entire product se ries.
User ’s Manual E-2 Legal Footnotes Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions.
User ’s Manual E-3 Legal Footnotes Hard Disk Dri ve (HDD) Cap acity 1 Gigabyte ( GB) means 10 9 = 1,000,000,000 bytes using powe rs of 10. The computer operating system, howe ver , reports storage capacity using powers of 2 for the definition of 1 GB = 2 30 = 1,073,741,824 bytes, and therefore shows less storage capacity .
User ’s Manual F-1 If your computer is stolen Appendix F If your computer is stolen Should your comput er be stolen , however , we’l l help you try to find it.
User ’s Manual F-2 If your computer is stolen TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH T echnical Servi ce and Support Leibnizstr . 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 921 Owner ’s details Country stolen: Machine type: (e.
User ’s Manual Glossa ry-1 Glossary Glossary The terms in this glossary cover topi cs related to this manual. Alternate naming is included for reference.
User ’s Manual Glossa ry-2 Glossary HDD: hard disk drive HD DVD: High Definition DVD HDCP: high-bandwidth digital content protection HDMI: high definition multimedia interface HDMI-CEC: high definit.
User ’s Manual Glossa ry-3 Glossary A AACS: A standard for copy protectio n that is used for HD DVD. It manages copy and output. adaptor: A device that provides a compatible connection betwe en two units. For example, the computer's intern al display adapter receives information from the software and translates it in to images on the screen.
User ’s Manual Glossa ry-4 Glossary Bluetooth: A short-range radio techn ology designed to simplify wireless communication among computers, communication devices and the Internet. board: A circuit board. An internal card containing electronic components, called chips, which perform a spe cific function or increase the capabilities of the system.
User ’s Manual Glossa ry-5 Glossary CD-RW : A Compact Disc-ReW ritable disc c an be rewritten many times. See also CD-ROM. character: Any letter , number , punctuation ma rk, or symbol used by the computer . Also synonymous with byte. chassis: The frame containing the comp uter .
User ’s Manual Glossa ry-6 Glossary CPU: Central Processing Unit. The portion of the computer that interp rets and executes instructions. CRT : Cathode Ray T ube. A vacuum tube in which beams projected on a fluorescent screen-producing luminous spots.
User ’s Manual Glossa ry-7 Glossary documentation: The set of ma nuals and/or ot her instructions written for the users of a computer system or application. Computer system documentation typically includes procedural and tu torial information as well as system functions.
User ’s Manual Glossa ry-8 Glossary escape guard time: A time before and after an escape code is sent to the modem which distin guishes between esca pes that are part of th e transmitted data, and escapes that are intended as a command to the modem.
User ’s Manual Glossa ry-9 Glossary H hard disk: A storage device compose d of a rigid platter or platters that can be magneti cally coded with data. Hard d isks hold much more information than diskettes and are used fo r long-term storage of programs and data.
User ’s Manual Glossary-10 Glossary interface: 1) Hardware and/or software component s of a system used specifically to connect one system or device to another .
User ’s Manual Glossary-1 1 Glossary Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewin g- side coating is etched into char acter formin g segments with leads that extend to the edge of the glass.
User ’s Manual Glossary-12 Glossary N network: A collection of computers and associated devi ces that are connected by communica tions facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to e xchange electroni c mail.
User ’s Manual Glossary-13 Glossary P pa r a l le l: Processes that occur simultan eously . In communications, it means the transmissi on of more t han one bit of info rmation at a time. On your computer , the p arallel por t provides a parall el communications inte rface between the computer and an appropriate device.
User ’s Manual Glossary-14 Glossary R Radio frequency inter ference (RFI) shield: A metal shield en closing the printed circuit boards of the printer or computer to prevent radio and TV interferen ce. All computer equipment g enerates radio frequency signals.
User ’s Manual Glossary-15 Glossary serial: Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel. On your computer , the se rial port provides a serial interface between the computer and an appropriate device.
User ’s Manual Glossary-16 Glossary volatile me mory: Random access memory (RAM) that stores information as long as power is supplied to the compute r .
User ’s Manual Index-1 Index Index A AC adaptor, 1-4 additional, 1-17 connecting, 3-2 ASCII characters, 5-7 B Battery charging, 6 -7 extending battery life, 6- 9 indicator, 6-1 location, 2-5 Monitor.
User ’s Manual Index-2 Index K Keyboard, 1- 9, 5-1 emulating keys on enhanced, 5-2 F1 ... F12 function keys, 5-2 hot keys, 5-3 typewriter keys, 5-1 Windows® special keys, 5-5 Keypad overla y, 1-12,.
User ’s Manual Index-3 Index R Recovery Discs, 3-11 Recovery hard di sk drive, 3-10, 3-11 Restarting the computer, 3-8 S Security lock attaching, 8-14 Sleep Mode, 1-13 setting, 3-6 System automatic,.
Ein wichtiger Punkt beim Kauf des Geräts Toshiba a300/a300d (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toshiba a300/a300d noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toshiba a300/a300d - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toshiba a300/a300d reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toshiba a300/a300d erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toshiba a300/a300d besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toshiba a300/a300d verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toshiba a300/a300d. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toshiba a300/a300d gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
