Benutzeranleitung / Produktwartung Adam (2013) des Produzenten Opel
Zur Seite of 216
OPEL ADAM Owner's Manual.
.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 31 Storage ........................................ 50 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
4 Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Press button c to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, press the brand emblem at the bottom half. Radio remote control 3 19, Central locking system 3 21, Load compartment 3 23.
In brief 7 Seat adjustment Seat positioning Pull handle, slide seat, release handle. Seat position 3 32, Seat adjustment 3 33. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Seat backrests Turn handwheel to adjust inclination.
8 In brief Head restraint adjustment Press release button, adjust height, engage. Head restraints 3 31. Seat belt Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx.
In brief 9 Exterior mirrors Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 26, Electric adjustment 3 26, Folding exterior mirrors 3 27, Heated exterior mirrors 3 27. Steering wheel adjustment Unlock the lever, adjust the steering wheel, then engage the lever and ensure it is fully locked.
10 In brief Instrument panel overview.
In brief 11 1 Power windows ..................... 28 2 Exterior mirrors ..................... 26 3 Cruise control ..................... 130 Speed limiter ....................... 131 4 Side air vents ...................... 117 5 Turn and lane-change signals, headlight flash, low beam and high beam .
12 In brief.
In brief 13 Exterior lighting Turn light switch: 7 = lights off 8 = sidelights 9 = headlights Automatic light control AUTO = automatic light control: exterior lighting is switched on and off automatically m = activation or deactivation of the automatic light control 8 = sidelights 9 = headlights Rear fog light Press r in the light switch.
14 In brief Turn and lane-change signals lever up = right turn signal lever down = left turn signal Turn and lane-change signals 3 105, Parking lights 3 105. Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 104. Horn Press j .
In brief 15 Washer and wiper systems Windscreen wiper 2 = fast 1 = slow P = interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 71, Wiper blade replacement 3 157.
16 In brief Rear window washer Push lever. Washer fluid is sprayed on the rear window and the wiper wipes a few times. Rear window wiper/washer 3 72. Climate control Heated rear window, heated exterior mirrors The heating is operated by pressing the Ü button.
In brief 17 Transmission Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal and then press the release button on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
18 In brief Stop-start system If the vehicle is at a low speed or at a standstill and certain conditions are fulfilled, activate an Autostop as follows: ■ Depress the clutch pedal ■ set the lever in neutral ■ release the clutch pedal An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer.
Keys, doors and windows 19 Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 23 Vehicle security ............................ 24 Exterior mirrors ............................ 26 Interior mirrors .
20 Keys, doors and windows Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system ■ Power windows The radio remote control has a range of approx. 20 metres. It can be restricted by external influences. The hazard warning flashers confirm operation.
Keys, doors and windows 21 Radio remote control synchronisation After replacing the battery, unlock the door with the key in the driver's door lock.
22 Keys, doors and windows The setting can be saved for the key being used. Memorised settings 3 21. Unlocking and opening the tailgate 3 23. Locking Close doors, load compartment and fuel filler flap. Press button e . If the driver's door is not closed properly, the central locking system will not work.
Keys, doors and windows 23 Fault in central locking system Unlocking Manually unlock the driver's door by turning the key in the lock. The passenger door can be opened by pulling the interior handle twice. The load compartment and fuel filler flap cannot be opened.
24 Keys, doors and windows Closing Use interior handle. Do not press the touchpad switch or the emblem whilst closing as this will unlock the tailgate again. Central locking system 3 21. General hints for operating tailgate 9 Warning Do not drive with the tailgate open or ajar, e.
Keys, doors and windows 25 Activating Press button e on the radio remote control twice within 15 seconds. Anti-theft alarm system The anti-theft alarm system is combined with the anti-theft locking system.
26 Keys, doors and windows The anti-theft alarm system can only be deactivated by pressing button c on the radio remote control or by switching on the ignition. A triggered alarm, which has not been interrupted by the driver, will be indicated by the hazard warning lights.
Keys, doors and windows 27 In position 0 no mirror is selected. Folding mirrors For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing.
28 Keys, doors and windows Automatic anti-dazzle Dazzle from following vehicles at night is automatically reduced. Windows Windscreen Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror.
Keys, doors and windows 29 Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again. Override safety function In the event of closing difficulties due to frost or the like, switch on the ignition, then pull the switch to the first detent and hold.
30 Keys, doors and windows Heated rear window Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling.
Seats, restraints 31 Seats, restraints Head restraints ............................ 31 Front seats ................................... 32 Seat belts ..................................... 35 Airbag system .............................. 38 Child restraints .
32 Seats, restraints Rear head restraints, height adjustment Pull the head restraint upwards and let engage. To move downwards, press the catch to release and push the head restraint downwards. Removal of rear head restraint E.g. when using a child restraint system 3 44.
Seats, restraints 33 ■ Sit with shoulders as far back against the backrest as possible. Set the backrest rake so that it is possible to easily reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel.
34 Seats, restraints Seat backrests Turn handwheel to adjust inclination. Do not lean on backrest while adjusting. Seat height Lever pumping motion up = seat higher down = seat lower Seat folding Pull release lever towards the front and fold backrest forwards.
Seats, restraints 35 Caution When seat height is in the highest position, push head restraints down and fold up sun visors before folding backrest forwards. Heating Activate seat heating by pressing ß button for the respective front seat. Activation is indicated by the LED in the button.
36 Seats, restraints Seat belts are designed to be used by only one person at a time. Child restraint system 3 44. Periodically check all parts of the belt system for damage, pollution and proper functionality. Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop.
Seats, restraints 37 Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing.
38 Seats, restraints Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered, the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision.
Seats, restraints 39 geschützt ist, da dies den TOD oder SCHWERE VERLETZUNGEN DES KINDES zur Folge haben kann. FR: NE JAMAIS utiliser un siège d'enfant orienté vers l'arrière sur un siège protégé par un COUSSIN GONFLABLE ACTIF placé devant lui, sous peine d'infliger des BLESSURES GRAVES, voire MORTELLES à l'ENFANT.
40 Seats, restraints zalecenia może być przyczyną ŚMIERCI lub POWAŻNYCH OBRAŻEŃ u DZIECKA. TR: Arkaya bakan bir çocuk emniyet sistemini KESİNLİKLE önünde bir AKTİF HAVA YASTIĞI ile korunmakta olan bir koltukta kullanmayınız. ÇOCUK ÖLEBİLİR veya AĞIR ŞEKİLDE YARALANABİLİR.
Seats, restraints 41 LV: NEKĀDĀ GADĪJUMĀ neizmantojiet uz aizmuguri vērstu bērnu sēdeklīti sēdvietā, kas tiek aizsargāta ar tās priekšā uzstādītu AKTĪVU DROŠĪBAS SPILVENU, jo pretējā gadījumā BĒRNS var gūt SMAGAS TRAUMAS vai IET BOJĀ.
42 Seats, restraints The side airbag system consists of an airbag in each front seat backrest. The location is identified by the word AIRBAG . The side airbag system is triggered in the event of a side impact of a certain severity. The ignition must be switched on.
Seats, restraints 43 Airbag deactivation The front passenger airbag system must be deactivated if a child restraint system is to be fitted on this seat. The side airbag and curtain airbag systems, the belt pretensioners and all driver airbag systems will remain active.
44 Seats, restraints Change status only when the vehicle is stopped with the ignition off. Status remains until the next change. Control indicator for airbag deactivation 3 83.
Seats, restraints 45 backbone, which is still very weak, is under less strain in the event of an accident. Suitable are restraint systems that comply with ECE 44-03 or ECE 44-04. Check local laws and regulations for mandatory use of child restraint systems.
46 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear seats activated airbag deactivated airbag Group 0: up to 10 kg or approx. 10 months X U 1 U 2 * Group 0+: up to 13 kg or approx.
Seats, restraints 47 ** = Move the front passenger seat in the rearmost adjustment position. Move seat height adjustment in the uppermost position and the headrest in the lowest position. Adjust seat backrest inclination as far as necessary to a vertical position to ensure that vehicle safety belt runs forwards from the upper anchorage point.
48 Seats, restraints IL = Suitable for particular ISOFIX restraint systems of the "specific-vehicle", "restricted" or "semi-universal" categories. The ISOFIX restraint system must be approved for the specific vehicle type.
Seats, restraints 49 ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by the ISOFIX logo on the backrest.
50 Storage Storage Storage compartments ................ 50 Load compartment ....................... 61 Roof rack system ......................... 67 Loading information ..................... 67 Storage compartments 9 Warning Do not not store heavy or sharp objects in the storage compartments.
Storage 51 Door pockets in both doors are designed to carry bottles. Additional cupholders or bottleholders are located in the rear side panels. Flexible cupholder strap A movable rubber strap is located in the storage compartment in front of the gear selector lever.
52 Storage Rear carrier system Rear carrier system for two bicycles The rear carrier system (Flex-Fix system) allows one bicycle to be attached to a pull-out carrier integrated into the vehicle floor. It is possible to attach one further bicycle on an adapter.
Storage 53 Pull release lever up. The system disengages and travels quickly out of the bumper. Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again.
54 Storage Swivel both tail lamps backwards as far as it will go. Fold out wheel recess Remove strap and fold out the wheel recess. Lock the rear carrier system Remove strap and swivel both clamping levers sidewards as far as it will go. Otherwise safe functionality is not guaranteed.
Storage 55 Push down the rack (1) and swivel handle (2) backwards to engage. Press button (1) and remove left part of rack (2). Press button (1) and insert left part of rack into the right part (2). Attaching the adapter When carrying two bicycles, the adapter must be fixed before attaching the first bicycle.
56 Storage 2. Turn the lever (1) forwards and hold, then lower the adapter (2) at the rear. 3. Release lever and check if the adapter is engaged securely. 4. Guide the strap attached to the adapter underneath the lever for folding back the rear carrier system.
Storage 57 3. Secure both bicycle wheels to the wheel recesses using the strap retainers. 4. Check the bicycle to make sure it is secure. Caution Ensure gap between bicycle and vehicle is at least 5 cm. If necessary, loosen handlebar and swivel sideways.
58 Storage ■ Without attached adapter: Push the lever (1) to disengage and hold. Pull the rack (2) backwards to fold the rear carrier system. ■ With attached adapter: 9 Warning Take care when disengaging the rear carrier system as it will tilt backwards.
Storage 59 3. Turn the lever (1) forwards and hold. 4. Lift the adapter (2) at the rear and remove. Disassembling the bicycle rack Press button (1) and remove upper part of rack (2). Press button (1) and reinstall rack (2). Arrange mounting bracket as shown in the illustration.
60 Storage Fold the rack backwards, then push forwards until it stops (1). Press the rack down at the rear (2). Fold in wheel recess Fold in wheel recess. Fasten strap. Stow the strap retainers accurately. Unlock the rear carrier system Swivel both clamping levers inwards as far as it will go.
Storage 61 Fold in number plate light Fold number plate light forwards. Retracting the rear carrier system Caution Take care that all foldable parts, e.g. wheel recesses and mounting brackets, are stowed accurately. Otherwise the rear carrier system might get damaged when trying to retract it.
62 Storage Pull the strap on one or both backrests and fold them down onto the seat cushion. To fold up, raise the backrests into upright position and let them engage audibly. The backrests are properly engaged when the red marks on both release straps are not visible.
Storage 63 ■ turn the lock hooks on both sides to the rear and push down the lashing eyes in the recesses, ■ raise the storage box and place it on the folded backrests, ■ remove storage box out of the load compartment.
64 Storage Rear floor storage cover Rear floor cover Lift up rear floor cover. Depending on the version, there are vehicle tools, jacking equipment or a tyre repair kit under the floor cover. Tools 3 170, tyre repair kit 3 176. Rear floor cover on version with subwoofer box Lift up rear part of floor cover to gain access to the warning triangle.
Storage 65 ■ move floor cover slowly to the front, taking care that the guiding bolts slide into the attachments of the load compartment, and allow the floor cover to lower into position, ■ close the floor cover by folding the upper part to the rear, and fix it with the Velcro fastener, ■ fold up rear backrests.
66 Storage Warning triangle The warning triangle is stowed with elastic straps in the load compartment below the tailgate. If the vehicle is equipped with a storage box in the load compartment, remove the storage box to gain access to the warning triangle 3 62.
Storage 67 Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. For further information contact your workshop. Follow the installation instructions and remove the roof rack when not in use.
68 Storage 9 Warning Always make sure that the load in the vehicle is securely stowed. Otherwise objects can be thrown around inside the vehicle and cause personal injury or damage to the load or car. ■ The payload is the difference between the permitted gross vehicle weight (see identification plate 3 197) and the EC kerb weight.
Instruments and controls 69 Instruments and controls Controls ....................................... 69 Warning lights, gauges and indi‐ cators ........................................... 77 Information displays ..................... 87 Vehicle messages .
70 Instruments and controls Heated steering wheel Activate heating by pressing * button. Activation is indicated by the LED in the button. The recommended grip areas of the steering wheel are heated quicker and to a higher temperature than the other areas.
Instruments and controls 71 Windscreen wiper/washer Windscreen wiper 2 = fast 1 = slow P = interval wiping § = off For a single wipe when the windscreen wiper is off, press the lever down. Do not use if the windscreen is frozen. Switch off in car washes.
72 Instruments and controls Adjustable sensitivity of the rain sensor Turn the adjuster wheel to adjust the sensitivity: low sensi‐ tivity = turn adjuster wheel downwards high sensi‐ tivity = turn adjuster wheel upwards Keep the sensor free from dust, dirt and ice.
Instruments and controls 73 Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the rear window is frozen. Switch off in car washes. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged.
74 Instruments and controls If outside temperature drops to 3 °C, a warning message is displayed in the Driver Information Centre with Uplevel-Display. 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C.
Instruments and controls 75 Set date format To switch between the available options, repeatedly press the MENU- TUNE knob. RDS clock synchronization The RDS signal of most VHF transmitters automatically sets the time. RDS time synchronisation can take a few minutes.
76 Instruments and controls Power outlets A 12 Volt power outlet is located in the centre console. Do not exceed the maximum power consumption of 120 watts. With ignition off, the power outlet is deactivated. Additionally the power outlet is deactivated in the event of low vehicle battery voltage.
Instruments and controls 77 Warning lights, gauges and indicators Instrument cluster The needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer Indicates vehicle speed. Odometer The bottom line displays the recorded distance in km.
78 Instruments and controls Fuel gauge Displays the fuel level or gas level in the tank depending on the operation mode. Control indicator Y illuminates if the level in the tank is low. Refuel immediately if it flashes. During liquid gas operation, the system automatically switches over to petrol operation when gas tanks are empty 3 78.
Instruments and controls 79 Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. Service display The engine oil life system lets you know when to change the engine oil and filter.
80 Instruments and controls ignition is switched on, most control indicators will illuminate briefly as a functionality test. The control indicator colours mean: red = danger, important reminder yello.
Instruments and controls 81 Control indicators in the instrument cluster.
82 Instruments and controls Control indicators in the centre console Turn signal O illuminates or flashes green. Illuminates briefly The parking lights are switched on. Flashes A turn signal or the hazard warning flashers are activated. Rapid flashing: failure of a turn signal light or associated fuse.
Instruments and controls 83 Airbag and belt tensioners v illuminates red. When the ignition is switched on, the control indicator illuminates for approx. 4 seconds. If it does not illuminate, does not go out after 4 seconds or illuminates whilst driving, there is a fault in the airbag system.
84 Instruments and controls Flashes when the engine is running Fault that could lead to catalytic converter damage. Ease up on the accelerator until the flashing stops. Seek the assistance of a workshop immediately. Service vehicle soon g illuminates yellow.
Instruments and controls 85 Illuminates with power steering reduced Power steering is reduced due to overheating of the system. Control indicator extinguishes when the system has cooled down. Stop-start system 3 121. Illuminates with power steering disabled Failure in the power steering system.
86 Instruments and controls Engine oil pressure I illuminates red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels.
Instruments and controls 87 Illuminates green Cruise control is active. Cruise control 3 130. Door open h illuminates red. A door or the tailgate is open. Information displays Driver Information Centre The Driver Information Centre (DIC) is located in the instrument cluster between speedometer and tachometer.
88 Instruments and controls Some of the displayed functions differ when the vehicle is being driven or at a standstill. Some functions are only available when the vehicle is being driven.
Instruments and controls 89 ■ Remaining Oil Life : indicates when to change the engine oil and filter 3 79 ■ Speed Warning : if exceeding the preset speed, a warning chime will be activated Selection and indication can be different between Midlevel- and Uplevel-Display.
90 Instruments and controls Submenus are: ■ Shift indication : Current gear is indicated inside an arrow. The figure above recommends upshifting for fuel saving reasons. Eco index display : The current fuel consumption is indicated on a segment display.
Instruments and controls 91 Graphic-Info-Display, Colour-Info-Display Depending on the vehicle configuration the vehicle has a ■ Graphic-Info-Display or ■ Colour-Info-Display with Touch- Screen functionality. Both displays are located in the instrument panel.
92 Instruments and controls The Colour-Information-Display indicates in colour: ■ time 3 74 ■ outside temperature 3 73 ■ date 3 74 ■ electronic climate control settings 3 113 ■ parking assis.
Instruments and controls 93 Vehicle messages Messages are indicated mainly in the Driver Information Centre (DIC), in some cases together with a warning and signal buzzer. Press the SET/CLR button, the MENU button or turn the adjuster wheel to confirm a message.
94 Instruments and controls No. Vehicle message 25 Left front turn signal failure 26 Left rear turn signal failure 27 Right front turn signal failure 28 Right rear turn signal failure 35 Replace batte.
Instruments and controls 95 ■ Lighting, bulb replacement ■ Wiper/washer system ■ Doors, windows ■ Radio remote control ■ Seat belts ■ Airbag systems ■ Engine and transmission ■ Tyre pressure ■ Vehicle battery Vehicle messages on the Colour-Info-Display Some important messages appear additionally in the Colour-Info-Display.
96 Instruments and controls Trip computer The menus and functions can be selected via the buttons on the turn signal lever 3 87. Press the MENU button to select W on the Uplevel-Display.
Instruments and controls 97 ■ Digital speed ■ Range ■ Instantaneous consumption Trip computer 1 and 2 The information of two trip computers can be reset separately for odometer, average consumption and average speed by pressing the SET/CLR button, making it possible to display different trip information for different drivers.
98 Instruments and controls On vehicles with LPG engines: Average consumption is indicated for the currently selected mode; LPG or Gasoline. Instantaneous consumption Display of the instantaneous consumption. On vehicles with LPG engines: Instantaneous consumption is indicated for the currently selected mode; LPG or Gasoline.
Instruments and controls 99 In the corresponding submenus the following settings can be changed: Languages Selection of the desired language. Time Date See Clock 3 74. Radio settings See Infotainment manual for further information. Phone settings See Infotainment manual for further information.
100 Instruments and controls Auto relock doors : Activates or deactivates the automatic relock function after unlocking without opening the vehicle. ■ Restore factory settings : Reset all settings to the default settings. Personal settings in the Colour-Info-Display When audio is switched on, press ; on the control panel.
Instruments and controls 101 Personalization by driver : Activates or deactivates the personalisation function. Auto wipe in reverse gear : Activate or deactivate automatic switching on of the rear window wiper when reverse gear is engaged. ■ Collision / detection Park assist : Activate or deactivate the ultrasonic sensors.
102 Lighting Lighting Exterior lighting .......................... 102 Interior lighting ........................... 106 Lighting features ........................ 108 Exterior lighting Light switch Turn light switch: 7 = lights off 8 = sidelights 9 = headlights Control indicator 8 3 86.
Lighting 103 The current status of the automatic light control is displayed In the Driver Information Centre with Uplevel- Display. When switching on the ignition, automatic light control is active. When headlights are on, 8 lights up. Control indicator 8 3 86.
104 Lighting Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling: turn thumb wheel ? to required position. 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden 3 = driver's seat occupied and load compartment laden.
Lighting 105 Turn and lane-change signals lever up = right turn signal lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated.
106 Lighting Reversing lights The reversing light comes on when the ignition is on and reverse gear is selected. Misted light covers The inside of the light housing may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing.
Lighting 107 Operate rocker switch: w = automatic switching on and off. press u = on. press v = off. Note In the event of an accident with airbag deployment the courtesy lights are turned on automatically. Dome light Spotlight incorporated in the interior lighting comes on when headlights are switched on.
108 Lighting Operate button with ignition switched on: m one brief press = on or off. T repeated brief presses = dimming stepwise. T long press = dimming continuously. The selected intensity remains the next time the ignition is switched on. Starlight comes on automatically when switching off ignition and extinguishes after opening a door.
Lighting 109 Path lighting Headlights, tail lights, reversing lights and number plate lights illuminate the surrounding area for an adjustable time after leaving the vehicle. Activating 1. Switch off ignition 2. remove ignition key 3. open driver's door 4.
110 Climate control Climate control Climate control systems ............. 110 Air vents ..................................... 117 Maintenance .............................. 118 Climate control systems Heating and ventilation system Controls for: ■ Temperature ■ Fan speed ■ Air distribution Heated rear window Ü 3 30.
Climate control 111 Demisting and defrosting the windows ■ Set temperature control to warmest level. ■ Set fan speed to highest speed. ■ Set air distribution control to l . ■ Switch on heated rear window Ü . ■ Open side air vents as required and direct them towards door windows.
112 Climate control Press button n again to switch off cooling. The air conditioning system cools and dehumidifies (dries) as soon as the outside temperature is slightly above the freezing point. Therefore condensation may form and drip from under the vehicle.
Climate control 113 Demisting and defrosting the windows V ■ Switch on cooling n . ■ Set temperature control to warmest level. ■ Set fan speed to highest level. ■ Set air distribution control to l . ■ Switch on heated rear window Ü . ■ Open side air vents as required and direct them towards the door windows.
114 Climate control Climate control settings are shown on the Graphic-Info-Display, or depending on the version, on Colour- Info-Display. Setting modifications are briefly popped-up in both displays, superimposed over the currently displayed menu. The electronic climate control system is only fully operational when the engine is running.
Climate control 115 Demisting and defrosting the windows V ■ Press button V . Activation is indicated by the LED in the button. ■ Press button n for cooling. Activation is indicated by the LED in the button. ■ Temperature and air distribution are set automatically and the fan runs at high speed.
116 Climate control Air distribution Turn right rotary knob for desired adjustment. Setting is indicated in the Info-Display. K = to foot well 9 = to windscreen, front door windows and foot well s = t.
Climate control 117 Press button 4 to activate air recirculation mode. Activation is indicated by the LED in the button. Press button 4 again to deactivate recirculation mode. 9 Warning The exchange of fresh air is reduced in air recirculation mode. In operation without cooling the air humidity increases, so the windows may mist up from inside.
118 Climate control Maintenance Air intake The air intake in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow. Pollen filter The pollen filter cleans dust, soot, pollen and spores from the air entering the vehicle through the air intake.
Driving and operating 119 Driving and operating Driving hints ............................... 119 Starting and operating ............... 119 Engine exhaust .......................... 124 Manual transmission .................. 124 Brakes ..............
120 Driving and operating Ignition switch positions 0 = Ignition off 1 = Steering wheel lock released, ignition off 2 = Ignition on 3 = Starting Retained power off The following electronic systems can.
Driving and operating 121 Possible reasons for a non-starting engine: ■ Clutch pedal not operated ■ Timeout occurred Turbo engine warm-up Upon start-up, engine available torque may be limited for a short time, especially when the engine temperature is cold.
122 Driving and operating An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer. During an Autostop, the heating and brake performance will be maintained.
Driving and operating 123 Restart of the engine by the stop-start system The selector lever must be in neutral to enable an automatic restart. If one of the following conditions occurs during an Autos.
124 Driving and operating Engine exhaust 9 Danger Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled. If exhaust gases enter the interior of the vehicle, open the windows. Have the cause of the fault rectified by a workshop.
Driving and operating 125 Caution It is not advisable to drive with the hand resting on the selector lever. Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit.
126 Driving and operating Fault 9 Warning If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available. During hard braking, the vehicle can no longer be steered and may swerve.
Driving and operating 127 Ride control systems Traction Control system The Traction Control system (TC) is a component of the Electronic Stability Control (ESC). TC improves driving stability when necessary, regardless of the type of road surface or tyre grip, by preventing the drive wheels from spinning.
128 Driving and operating ESC is operational after each engine start as soon as the control indicator b extinguishes. When ESC operates b flashes. 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions.
Driving and operating 129 Stop-start system 3 121. Deactivation Press button B ; LED in the button extinguishes and a message pops-up in the Driver Information Centre. Each time the engine is started, City mode is deactivated. Overload If the steering in City mode is heavily loaded, e.
130 Driving and operating Driver assistance systems 9 Warning Driver assistance systems are developed to support the driver and not to replace his attention. The driver accepts full responsibility when driving the vehicle. When using driver assistance systems, always take care regarding the current traffic situation.
Driving and operating 131 Reduce speed With cruise control active, hold thumb wheel turned to SET/- or briefly turn to SET/- repeatedly: speed decreases continuously or in small increments. Deactivation Press button y , control indicator m in instrument cluster illuminates white.
132 Driving and operating Alternatively accelerate to the desired speed and briefly turn thumb wheel to SET/- : the current speed is stored as maximum speed. Speed limit is displayed in the Driver Information Centre. Change speed limit With speed limiter active, turn thumb wheel to RES/+ to increase or SET/- to decrease the desired maximum speed.
Driving and operating 133 The rear parking assist makes parking easier by measuring the distance between the vehicle and rear obstacles. It informs and warns the driver by giving acoustic signals. The system has four ultrasonic parking sensors in the rear bumper.
134 Driving and operating The front-rear parking assist measures the distance between the vehicle and obstacles in front and behind the vehicle. The system gives acoustic signals and display messages. The system has six ultrasonic parking sensors each in the rear and front bumper.
Driving and operating 135 Operation When reverse gear is engaged, the front and rear parking assist is ready to operate. An illuminated LED in the parking assist button D indicates that the system is ready to operate. The front parking assist can also be activated at a speed up to 11 km/h with a brief press of the parking assist button.
136 Driving and operating In the Colour-Info-Display, distance is displayed by coloured zones in front of or behind the vehicle. The distance indication in the Driver Information Centre can be inhibited by vehicle messages with a higher priority.
Driving and operating 137 Button logic operates the systems by pressing as follows: ■ If only front-rear parking assist is active, a brief press deactivates front-rear parking assist. ■ If only front-rear parking assist is active, long press activates advanced parking assist.
138 Driving and operating Parking slot searching mode Select parallel or perpendicular parking slot on Driver Information Centre by pressing the SET/CLR button or on Colour-Info Display tap icon 6 or 7 . When a slot is detected, a visual feedback in the Driver Information Centre or Colour-Info-Display and an acoustic signal is given.
Driving and operating 139 A brief vibration in the steering wheel after engaging reverse gear indicates that the steering is controlled by the system. Then the vehicle is steered into the slot automatically by giving the driver detailed instructions for braking, accelerating and gear shifting.
140 Driving and operating If the system is equipped with Colour- Info-Display, select the type of parking slot by tapping the display icon 6 or 7 . The display shows the type of parking slot. Changing the parking side The system is configured to detect parking slots by default on the passenger side.
Driving and operating 141 ■ exceeding number of maximum gear changes: 8 parking cycles when parallel parking or 5 cycles when perpendicular parking, ■ switching off the ignition. Deactivation by the driver or by the system during manoeuvring will be indicated by Parking Deactivated in the Driver Information Centre or Colour-Info-Display.
142 Driving and operating correct distance indication in the upper part of these vehicles cannot be guaranteed. Objects with a very small reflection cross-section, e.g. objects of narrow size or soft materials, may not be detected by the system. Parking assist systems do not detect objects outside the detection range.
.
144 Driving and operating Fuel Fuel for petrol engines Only use unleaded fuel that complies with European standard EN 228 or E DIN 51626-1 or equivalent. Your engine is capable of running with E10 fuel that fulfills these standards. E10 fuel contains up to 10 % bioethanol.
Driving and operating 145 Pressing the LPG button switches between petrol and liquid gas operation as soon as the required parameters (coolant temperature, gas temperature and minimum engine speed) have been reached. The requirements are usually fulfilled after approx.
146 Driving and operating Refuelling 9 Danger Before refuelling, switch off the engine. Switch off any mobile phones. Follow the operating and safety instructions of the gas station when refuelling. 9 Danger Fuel is flammable and explosive. No smoking.
Driving and operating 147 Liquid gas refuelling Follow the operating and safety instructions of the filling station when refuelling. The filling valve for the liquid gas is behind the fuel filler cap. Unscrew protective cap from the filler neck. Fit the required adapter.
148 Driving and operating 9 Warning Due to the system design, an escape of liquid gas after releasing the locking lever is unavoidable. Avoid inhaling. 9 Warning The liquid gas tank may only be filled to 80% for safety reasons. The multivalve on the liquid gas tank automatically limits the fill quantity.
Driving and operating 149 Croatia, Latvia, Lithuania, Macedonia, Austria, Poland, Portugal, Romania, Sweden, Switzerland, Serbia, Slovakia, Slovenia, Czech Republic, Turkey, Ukraine, Hungary Fuel filler cap Only use genuine fuel filler caps.
150 Vehicle care Vehicle care General Information ................... 150 Vehicle checks ........................... 151 Bulb replacement ....................... 157 Electrical system ........................ 165 Vehicle tools ........................
Vehicle care 151 ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery.
152 Vehicle care 9 Danger The ignition system uses extremely high voltage. Do not touch. Bonnet Opening Pull the release lever and return it to its original position.
Vehicle care 153 Different dipsticks are used depending on engine variant. When the engine oil level has dropped to the MIN mark, top up engine oil. We recommend the use of the same grade of engine oil that was used at last change. The engine oil level must not exceed the MAX mark on the dipstick.
154 Vehicle care If the cooling system is cold, the coolant level should be above the filling line mark. Top up if the level is low. 9 Warning Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly. To top up use a 1:1 mixture of released coolant concentrate mixed with clean tap water.
Vehicle care 155 The brake fluid level must be between the MIN and MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop.
156 Vehicle care In vehicles with stop-start system, be sure to have the AGM (Absorptive Glass Mat) battery replaced with another AGM battery An AGM battery can be identified by the label on the battery. We recommend the use of an original Opel battery.
Vehicle care 157 ■ See the Owner's manual for further information. ■ Explosive gas may be present in the vicinity of the battery. Wiper blade replacement Lift the wiper arm until it stays in the raised position, press button to disengage the wiper blade and remove.
158 Vehicle care Low beam outer bulb (1). High beam inner bulb (2). Low beam (1) 1. Rotate the cap anticlockwise and remove it. 2. Press the clip to disengage bulb holder. Withdraw the bulb holder from the reflector. 3. Detach the bulb from the bulb holder and replace the bulb.
Vehicle care 159 2. Press the clip to disengage bulb holder. Withdraw the bulb holder from the reflector. 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder with the clip upwards and engage into the reflector until it clicks.
160 Vehicle care Front turn signal lights 1. Undo screw and remove cover. 2. Undo screw and remove light assembly from the bumper. 3. Disengage and remove the bulb socket by turning anticlockwise. 4. Remove bulb by turning anticlockwise a little and withdrawing.
Vehicle care 161 Version with subwoofer box: remove load compartment floor cover, on right side also remove the tool box to gain access to the cover 3 64. Version with storage box: remove storage box to gain access to the cover 3 62. 2. Unscrew the plastic securing nut from the inside by hand.
162 Vehicle care Fit light assembly with the retaining pins into the recesses of the vehicle body and tighten the securing nut from inside the load compartment.
Vehicle care 163 4. Remove bulb by turning anticlockwise slightly and withdrawing. Replace the bulb. 5. Insert the bulb socket into the assembly and turn clockwise. 6. Replace light assembly in the bumper and fix with the screw. 7. Insert cover into the bumper and fix with the screw.
164 Vehicle care Number plate light 1. Insert screwdriver in recess of the cover, press to the side and release spring. 2. Remove lamp downwards, taking care not to pull on the cable. 3. Remove bulb holder from lamp housing by turning anticlockwise. 4.
Vehicle care 165 Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. There are two fuse boxes in the vehicle: ■ in the front left of the engine compartment, ■ in left-hand drive vehicles behind the light switch, or, in right-hand drive vehicles, behind the glovebox.
166 Vehicle care Engine compartment fuse box The fuse box is in the front left of the engine compartment. Disengage the cover and fold it upwards until it stops.
Vehicle care 167 No. Circuit 18 Engine control module 19 Fuel pump 20 – 21 Injection coil 22 – 23 Injection system 24 Washer system 25 Lighting system 26 Engine control module 27 – 28 Engine control module 29 Engine control module 30 – 31 Left headlamp 32 Right headlamp 33 Engine control module 34 Horn No.
168 Vehicle care Instrument panel fuse box In left-hand drive vehicles, the fuse box is behind the light switch in the instrument panel. Hold the handle, then pull and fold down the light switch. In right-hand drive vehicles, the fuse box is located behind a cover in the glovebox.
Vehicle care 169 No. Circuit 1 – 2 – 3 Power windows 4 Voltage transformer 5 Body control module 1 6 Body control module 2 7 Body control module 3 8 Body control module 4 9 Body control module 5 1.
170 Vehicle care Vehicle tools Tools Vehicles with tyre repair kit Some tools and the towing eye are located together with the tyre repair kit in a tool box in the load compartment below the floor cover. On version with storage box, remove box first 3 62.
Vehicle care 171 On version with subwoofer box, the tools and the towing eye are located together with the tyre repair kit and the warning triangle in the box below the floor cover. To gain access, remove floor cover: fold rear part to the front and pull out the cover to the rear 3 64.
172 Vehicle care Tyre designations E.g. 195/55 R 16 95 H 195 = Tyre width, mm 55 = Cross-section ratio (tyre height to tyre width), % R = Belt type: Radial RF = Type: RunFlat 16 = Wheel diameter, inches 95 = Load index e.
Vehicle care 173 If the tyre pressure must be reduced or increased on a vehicle with tyre pressure monitoring system, switch off ignition. After adjusting tyre pressure switch on ignition and select the relevant setting on the page Tyre load in the Driver Information Centre, 3 87.
174 Vehicle care A detected low tyre pressure condition is indicated by the control indicator w 3 85. If w illuminates, stop as soon as possible and inflate the tyres as recommended 3 207. After inflating, driving may be required to update the tyre pressure values in the Driver Information Centre.
Vehicle care 175 Select: ■ Light for comfort pressure up to 3 people ■ Eco for Eco pressure up to 3 people ■ Max for full loading Auto learn function After changing wheels the vehicle must be stationary for approx. 20 minutes, before the system recalculates.
176 Vehicle care Changing tyre and wheel size If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the speedometer as well as the nominal tyre pressure and make other vehicle modifications. After converting to a different tyre size, have the label with tyre pressures replaced.
Vehicle care 177 Tyre damage exceeding 4 mm or that is at tyre's sidewall cannot be repaired with the tyre repair kit. 9 Warning Do not drive faster than 80 km/h. Do not use for a lengthy period. Steering and handling may be affected. If you have a flat tyre: Apply the parking brake and engage first gear.
178 Vehicle care On versions with subwoofer box the tyre repair kit is located in the box under the floor cover in the load compartment. To use tyre repair kit, firstly remove floor cover: fold rear part to the front and pull out the cover to the rear 3 64.
Vehicle care 179 9. Connect the compressor plug to the power outlet or cigarette lighter socket. To avoid discharging the battery, we recommend running the engine. 10. Set the rocker switch on the compressor to I . The tyre is filled with sealant. 11.
180 Vehicle care hose directly onto tyre valve and compressor when doing this. If tyre pressure is more than 1.3 bar, set it to the correct value. Repeat the procedure until there is no more loss of pressure. If the tyre pressure has fallen below 1.3 bar, the vehicle must not be used.
Vehicle care 181 ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle. ■ Do not start the vehicle when it is raised on the jack. ■ Clean wheel bolts and thread with a clean cloth before mounting the wheel.
182 Vehicle care Some versions have sill panellings with covered vehicle jacking points: pull out the cover at the respective jacking point firstly. 4. Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping.
Vehicle care 183 Rear arm position of the lifting platform centrically under the recess of the sill. Front arm position of the lifting platform at the underbody.
184 Vehicle care 4. Lift the spare wheel holder a bit by hand and unhook the catch. 5. Lower the spare wheel holder. 6. Lift the spare wheel holder a bit by hand and detach the safety cable. 7. Lower holder all the way and remove spare wheel. 8. Change the wheel 3 180.
Vehicle care 185 2. Untwist wing nut and remove tool box. 3. Position the damaged wheel to stand upright into the tool box spare, facing to the front. 4. Remove strap 1 from the tool box and place the loop end of the strap through the right side lashing eye.
186 Vehicle care 9. Position the tool box in the inside of the wheel and secure it with strap 2 inserted through two spokes of the wheel. Wheels with tyre size bigger than 195/55R16 1. Fold down backrests of the rear seats 3 61. 2. Remove strap 1 from the tool box.
Vehicle care 187 9 Warning Storing a jack, a wheel or other equipment in the load compartment could cause injury if they are not fixed properly. During a sudden stop or a collision, loose equipment could strike someone. Store jack and tools always in the respective storage compartments and secure them by fixing.
188 Vehicle care ■ Never expose the battery to naked flames or sparks. ■ A discharged vehicle battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery.
Vehicle care 189 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Reverse above sequence exactly when removing leads. Towing Towing the vehicle Disengage the cap by pushing on the marked position.
190 Vehicle care Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. When the engine is not running, considerably more force is needed to brake and steer. To prevent the entry of exhaust gases from the towing vehicle, switch on the air recirculation and close the windows.
Vehicle care 191 Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. After towing, unscrew the towing eye. Insert cap and engage in the bumper. Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease.
192 Vehicle care On vehicles with emblem touchpad: when cleaning with a high-pressure jet cleaner ensure a minimum distance of 30 cm when working around the tailgate to prevent unintended unlocking. Thoroughly rinse and leather-off the vehicle. Rinse leather frequently.
Vehicle care 193 After the underbody is washed, check the underbody and have it waxed if necessary. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop. Before and after winter, wash the underbody and have the protective wax coating checked.
194 Service and maintenance Service and maintenance General information ................... 194 Recommended fluids, lubricants and parts ..............
Service and maintenance 195 Make sure that the Service and Warranty Booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle.
196 Service and maintenance Select the appropriate engine oil based on its quality and on the minimum ambient temperature 3 199. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty.
Technical data 197 Technical data Vehicle identification .................. 197 Vehicle data ............................... 199 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is visible through the windscreen. Identification plate The identification plate is located on the left door frame.
198 Technical data Information on identification label: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Identification Number 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gr.
Technical data 199 Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Serbia, Turkey) Only Is.
200 Technical data International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines.
Technical data 201 All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines (including CNG, LPG, E85) Petrol engines (including CNG, L.
202 Technical data Engine data Sales designation 1.2 1.4 1.4 LPG 1.4 Engine identifier code A12XEL A14XEL A14XEL A14XER Number of cylinders 4 4 4 4 Piston displacement [cm 3 ] 1229 1398 1398 1398 Engi.
Technical data 203 Performance Engine A12XEL A14XEL A14XER Maximum speed 2) [km/h] Manual transmission 165 176 185 Automatic transmission – – – 2) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
204 Technical data Vehicle weight Kerb weight, basic model without any optional equipment Engine Manual transmission Automatic transmission without/with air conditioning [kg] A12XEL 1086/1101 – A14X.
Technical data 205 Length of load compartment floor [mm] 462 Length of load compartment with folded rear seats [mm] 1041 Load compartment width [mm] 954 Load compartment height [mm] 874 Wheelbase [mm] 2311 Turning circle diameter [m] 10.
206 Technical data Capacities Engine oil Engine A12XEL A14XEL A14XER including Filter [l] 4.0 4.0 4.0 between MIN and MAX [l] 1.0 1.0 1.0 Fuel tank Engine A12XEL A14XEL A14XER Petrol, refilling quanti.
Technical data 207 Tyre pressures Comfort with up to 3 people ECO with up to 3 people With full load Engine Tyres front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) A12XEL, A14XEL, A14XER 175/70 R14, 185/60 R15, 185/65 R15 200/2.
208 Customer information Customer information Customer information ................ 208 Vehicle data recording and pri‐ vacy ........................................... 208 Customer information Declaration of conformity This vehicle has systems that transmit and/or receive radio waves subject to Directive 1999/5/EC.
Customer information 209 ■ Vehicle reactions in particular driving situations (e.g. inflation of an airbag, activation of the stability regulation system) ■ Environmental conditions (e.g. temperature) These data are exclusively technical and help identifying and correcting errors as well as optimizing vehicle functions.
210 Index A Accessories and vehicle modifications .......................... 150 Adjustable air vents ................... 117 Airbag and belt tensioners ........... 83 Airbag deactivation ................ 43, 83 Airbag system .........................
211 Cupholders .................................. 50 Curtain airbag system .................. 42 D Danger, Warnings and Cautions ... 4 Daytime running lights ............... 104 Declaration of conformity ............ 208 Door open ....................
212 Instrument panel fuse box ......... 168 Instrument panel illumination ..... 164 Instrument panel illumination control .................................... 106 Instrument panel overview ........... 10 Interior care ............................... 193 Interior lighting .
213 Service ....................................... 118 Service display ............................ 79 Service information .................... 194 Service vehicle soon .................... 84 Side airbag system ...................... 41 Side blind spot alert .
214.
Ein wichtiger Punkt beim Kauf des Geräts Opel Adam (2013) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Opel Adam (2013) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Opel Adam (2013) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Opel Adam (2013) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Opel Adam (2013) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Opel Adam (2013) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Opel Adam (2013) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Opel Adam (2013). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Opel Adam (2013) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
