Benutzeranleitung / Produktwartung RV4000 des Produzenten Magnadyne
Zur Seite of 24
Operation and Installation Manual ® RV4000 AM / FM Stereo Multi-Media Receiver EQ 1 AS/PS 2 SLP 3 ALM 4 DISP 5 DIM 6 PUSH 3-Beam Laser Pickup A B AUX AM/FM DISC SPEAKER SPK FM ST RESET AUX HEADPHONES.
Please take the time to read all of the information in this manual. Familiarity with operation and installation procedures will help you obtain the best possible performance from your new AM/FM Stereo Multi-Media Receiver. WARNING! To prevent fire or electrical shock hazard, do not expose this product to moisture, or remove cover or bottom screws.
Button Locations and Functions 3 1. Power On/Off: Press to turn the unit on or off. 2. Disc Door: To play a disc, insert the disc with label facing forward. 3. Disc Door Release: Press to open the door so the disc can be inserted. 4. Auxiliary Button (AUX): Press to choose auxiliary audio in mode.
4 Button Locations and Functions (Continued) 16 . Dimmer Button (DIM): Press to dim the lighting in the display area. Sequential presses will select dif- ferent levels of display area lighting. 17. Radio Preset Button (6): Recalls a memorized radio station, and programs a radio station into memory.
5 General Operations Selecting a Play Source: To select a play source, press one of the follow- ing mode buttons: AUX (Auxiliary Audio Input), AM/FM (AM or FM Radio Band) or DISC (Music) Dimming the Display: Press the DIM button to select the desired level of brightness for the display area.
6 Sound Controls Bass: Select the Bass mode by pressing the VOLUME knob. Increase the Bass by rotating the VOLUME knob clockwise. Decrease the Bass by rotating the knob counterclockwise. After 6 seconds control reverts back to volume control. Bass, Treble and Balance Control Select the desired sound mode by pressing the VOLUME knob.
7 Sound Controls (Continued) Mute: Press the button to mute the volume level. Press the button again to restore the volume. Speaker Selection Selecting Speaker Sets: • Press the A button to toggle speaker set A on and off. “SPK A” appears in the display when speaker set A is on.
8 Sleep Timer Operation Setting the Sleep Timer: 1. Press the SLP button until the “SLP 10” appears in the display. 2. Keep pressing the SLP button again until the desired sleep time appears in the display (00, 10, 20, 30, 40, 50, 60, 70, 80 minutes).
9 Alarm Operation Setting the Alarm Timer: 1. Press the ALM button and the clock will appear in the display with the hour number flashing. 2. Rotate the VOLUME knob until the correct Hour appears in the display. “ALM” will appear in the display indicating the alarm is activated.
10 Radio Operations Selecting the Play Source: Press the AM/FM button and “rAdIO” appears in the display. After a brief moment either AM or FM will appear in the display. Selecting the AM or FM: Press the AM/FM button repeatedly and select from FM 1, FM 2, FM 3, AM 1 or AM 2.
11 Disc Warnings DVD 12cm disc (Single-sided disc only) CD 12cm disc MP3 12cm disc Label side up Do not touch the underside of the disc Do not bend Wipe the disc from the center toward the outside edg.
12 Music Disc Operation General Operations: 1. Push the door access the disc player. 2. Insert the disc onto the hub with the label facing forward. Use your thumb to make sure the disc snaps onto the hub. 3. Press the DISC button and “LOAd” will appear in the display.
13 Music Disc Operation (Continued) Removing the Disc: 1. Push the door to access the disc player. Wait until the disc stops spinning before opening up the door. 2. Use your finger to remove the disc from the hub. 3. Close the door. Pausing the Disc: Press the ll button to pause the disc, press it again to resume play.
14 MP3 Disc Operation General Operations: 1. Push the door access the disc player. 2. Insert the disc onto the hub with the label facing forward. Use your thumb to make sure the disc snaps onto the hub. 3. Press the DISC button and “LOAd” will appear in the display.
15 MP3 Disc Operation (Continued) Removing the Disc: 1. Push the door to access the disc player. Wait until the disc stops spinning before opening up the door. 2. Use your finger to remove the disc from the hub. 3. Close the door. Pausing the Disc: Press the ll button to pause the disc, press it again to resume play.
16 Audio Input Selecting the Audio Input Source: Note 1: The RV4000 does not control the device, it just allows the audio to be played through the system. Note 2: If the rear audio input is being used once you plug a device into the front audio input jack the audio will be diverted to playing the front device.
17 The LCD display may fail to function normally due to the vehicle’s battery condition, and could require resetting the radio microprocessor if: • The vehicle has been “jump started” from a dead battery condition. • The vehicle battery becomes very low and is quick-charged.
18 Installation 9 4 5 / 8 ” 6 1 / 4 ” Chassis Opening Structural Stud Wall Panel Caution: Do not install radio without rear cover installed: No user -ser viceable parts inside.
19 Speaker Connections _ + Gray Wire White/Black Wire (Common -) _ + Gray/Black Wire Right Speaker B Left Speaker B _ + Brown/Black Wire White Wire (Common -) _ + Brown Wire Right Speaker A Left Speak.
20 Wiring and Auxiliary Connections Red Wire (+) to 12 Volt DC Power Black Wire Ground Music Disc Player (Optional) Audio In Audio Out 10A Fuse External Automotive Ty pe Antenna (Optional) In-Dash Uni.
21 Outdoor Antenna Grounding: If an outside antenna is connected to the receiver, be sure the antenna system is grounded, so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electrical Code, ANSI/NFPS No.
22 Warranty ONE (1) YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agents will within one year from the date of sale to you, repair, replace or refund the retail sales price of said pro.
23.
© Copyright 2011 Magnadyne Corporation RV4000-UM Rev. A 5-19-11.
Ein wichtiger Punkt beim Kauf des Geräts Magnadyne RV4000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Magnadyne RV4000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Magnadyne RV4000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Magnadyne RV4000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Magnadyne RV4000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Magnadyne RV4000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Magnadyne RV4000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Magnadyne RV4000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Magnadyne RV4000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
