Benutzeranleitung / Produktwartung FOOTPRINT H50 des Produzenten Frymaster
Zur Seite of 100
Frymaster, a member of the Co mmercial Food Equipm ent Serv ice Association, recommends using CFESA Certified Tec hnicians. 24-Hour Service Hotline 1-800-551-8633 JUNE 2009 www.
NOTICE IF, DURING THE WARRANTY PERIOD, THE CUST OMER USES A PART FOR THIS ENODIS EQUIPMENT OTHER TH AN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER DEAN, OR ANY OF ITS AUTH ORIZED SERVICE CENTERS, AND/OR THE PART BEIN G USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THI S WARRANTY WILL BE VOID.
DANGER No structural material on the fryer should be altered or removed to accommodate placement of the fryer under a hood. Questions? Call the Frymaster Dean Service Hotline at 1-800-551-8633. DANGER Adequate means must be provided to limit the movement of this appliance without depending upon the gas line connection.
PRO H50/55-SERIES GAS FRYERS TABLE OF CONTENTS i CHAPTER 1: Service Procedures 1.1 Functional Description ..................................................................................................... ............................. 1-1 1.1.1 The Electroni c Ignition System .
PRO H50/55-SERIES GAS FRYERS TABLE OF CONTENTS ii 1.11.6.4 FPPH350/355 Transformer/ Filter Box .................................................................................. .....1-48 1.11.7 Modular Bask et Lift (1 00/120V) .......................
1-1 Inside the Ignition Module TD Out to Gas Valve To A l a r m 25 V + GND HV Ignition Wire Flame Sensor Coil PRO H50/55-SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.
1-2 valve via a normally closed high-limit switch (and, in fryers with built-in filtration system s, a normally closed drain safety switch). Simultaneous ly, the m odule causes the ignitor to spark for 4 seconds to light the burner. A flame sensor verifies the burner ignition by measuring the flow of microamps through the flam e.
1-3 CURRENT FLOW THROUGH INTERFACE BOARD 106-0386 (PRO SERIES APPLICATION) 1 2 3 4 5 6 7 8 9 10 11 12 J3 J2 PIN 1 J2 1 2 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 J1 LEFT-VAT FULL- OR R.
1-4 FREQUENTLY USED TEST POINTS FOR INTERFACE BOARD 106-0386 TEST METER SETTING PINS RESULTS 12VAC Power to Controller 50VAC Scale 1 and 3 on J3 or J2 12-18 24VAC Power to Right Module 50VAC Scale 8 o.
1-5 3. After servicing is complete, reconnect the unit to the gas supply, reattach restraining devices, and plug in the electrical cords. 1.3 Cleaning the Gas Valve Vent Tube 1. Set the fryer power switch and the gas valve to the OFF position. 2. Carefully unscrew the vent tube from the gas valve.
1-6 4. On non-CE fryers only , place the gas valve in the ON position. 5. Place the fryer power switch in the ON position. Wh en the burner has lit and burned steadily for at least one minute, compare the gas pressure r eading to the pressure for the corresponding gas in the appropriate table below.
1-7 7. Place the fryer power switch (and the gas valve in non-CE fryers) in the OFF position. Remove the fitting from the pressure tap hole and reinstall the pressure tap plug. 1.5 Measuring Flame Current When the burner flame is properly adjusted, it will produce a current between 2.
1-8 1.6.2 Replacing the Temperature Probe or High-Limit Thermostat 1. Disconnect the fryer from the electrical supply. 2. Drain cooking oil below the level of the probe or thermostat. 3. Lift up on the bezel to disengage the tabs on its lower edge from the control panel frame.
1-9 b. If replacing the high-limit thermostat, use a pin pusher to disconnect the lead running to the connector and insert the corresponding lead from the new thermostat. Disconnect the other lead from the drain safety switch and connect the remaining lead from the new thermostat.
1-10 1.6.5 Replacing an Ignitor Assembly DANGER Drain the frypot or remove the handle from the drain valve before proceeding further. 1. Disconnect the fryer from the electrical supply. 2. Disconnect the flame sensor wire by carefully pulling its push-on terminal f rom the terminal strip on the ignitor.
1-11 2. Remove the blower motor shield and separate the blower motor from the housing as shown in the illustration on the following page. Remov e these screw s to remove the sh ield fro m the blower assembly. Remove these nuts to separate the blower motor from the housing.
1-12 6. Light the fryer in accordance with the procedure described in Chapter 3, Section 3.2 of the Pro H55-Series Gas Fryer Installation and Operation Manual (P/N 819-5991). 7. After the burners have been lit for at least 90 seconds, observe the flames through the burner sight glasses located on each side of the combustion air blower.
1-13 1.6.7 Replacing a Gas Valve DANGER Drain the frypot or remove the handle from the drain valve before proceeding further. 1. Disconnect the fryer from the electrical and gas supplies. 2. Disconnect the drain safety and high-limit thermostat wires from the gas valve.
1-14 ALL OTHER VALVES 4. Carefully unscrew the valve from the manifold. NOTE: Som e models may have the valve attached to the manifold by means of a pipe union.
1-15 8. Remove the washers and tubular spacers from th e m ounting studs, then pull the inner covers straight out toward you until clear of the mounting studs. 9. Grasp the burner firmly and pull it toward you un til it clears the burner channels, taking care not to damage the ceramic tiles in the process.
1-16 3. Position a container beneath the oil return fitti ng at the front of the cabinet. Disconnect the flexible oil line from the fitting, allowing any residual oil to drain into the container. 4. At the rear of the fryer, unplug the left connector (as viewed from the rear of the fryer) from the transformer box.
1-17 DANGER DO NOT attempt to drain more than one full fry pot or two split frypots into the SDU at one time. 3. Dismount the topcap by removing the screws on the bottom of each front corner and lifting the topcap straight up.
1-18 20. Remove the drain valve(s), temp erature probe(s), high-limit thermostat(s), and ignitor assemblies. Inspect each of these components carefully and install them in the replacement frypot if they are in serviceable condition. Use Loctite ® PST56765 sealant or equivalent on component threads.
1-19 Disassembling A Frypot (Full-vat Illustrated) Spacers Spacer 10 2 3 4 5 6 7 8 1 11 9.
1-20 To re-assemble with new insulation and/or upp er burner rails (use illustration on page 1-23): 13. Place the “L” shaped pieces of com bustion cham ber insulation (1) in the front and rear corners of both upper rail-retaining slots. 14. Use a small amount of furnace or m uffler repair cement to seal the gaps at each end of both lower rails.
1-21 25. Insert the upper front insulation (10) into its re tainer (11), making sure that the holes in each piece are aligned with one another. Install the assembly with the insulation side toward the frypot and secure with ¼”-20 washer-nuts. Do not over tighten.
1-22 Re- assem bling A Fryp ot (Full-vat Illu stra ted) 6 5 4 1 2 7 8 9 1 3 10 11 12 13 14 18 20 19 17 16 15 24 23 21 22.
1-23 1.7 Troubleshooting and Problem Isolation Because it is not feasible to attempt to include in this m anual every conceivable problem or trouble condition that might be encountered, this section i.
1-24 valve handle appears to be in the closed position, the microswitch is still open). If the valve is fully closed, refer to the troubleshooting guide, TROUBLESHOOTING THE 24 VAC CIRCUIT .
1-25 If the fryer’s gas and air supplies are okay, the probl em is mo st likely with one of the electrical components. Examine the ignition m odule and c ontroller for signs of melting, distortion, and/or discoloration due to excessive heat build-up in the fryer (this condition usually indicates improper flue performance).
1-26 If these causes are ruled out, the probable cause is a misadjusted gas valve regulator. Refer to Section 1.4, Checking the Burner Manifold Gas Pressure , for the gas valve adjustment procedure.
1-27 COMMON COMPUTER COMPLAINTS Most problems concerning computers have to do with program ming them. There are four com mon complaints: 1. Fryer constantly displays “ HI .” Cause: Setpoint is incorrect or missing. Corrective Action: Press 1650, enter the correct setpoint using keypad, then press to lock in the setpoint.
1-28 Sediment Particle FLOW Up for reverse Down for forward PUMP • Shortening that remained in the pan after prev ious f iltering solidified in the suction tube recess in the bottom of the pan or the suction tube. Adding hot oil to the pan and waiting a few minutes will usually correct this problem.
1-29 M P u m p R ela y C o il Micro-swi tches Pump Motor Swit ch Pu m p M o to r S ole n oid s 24 VAC FootPrint Pro Schem atic Pum p Heater Tape Verifying Solenoid Operation Proper operation of the 24.
1-30 100/120V Modular Basket Lift Assembly P/N 106180 7SP (TYPICAL) the frypot until the rod loses contact with the upper microswitch, cutting power to the motor and again reversing the direction of current flow. Problems with the basket lift can be grouped into three categories: • Binds and jams • Motors and gears • Electronics.
1-31 1.7.8 Interpretation of Analog Controller Lights Power light on, heat light cycling, trouble light off, and melt light on: • If fryer oil temperature is below 180ºF (82º C), the lights indicate the unit is operating normally.
1-32 The following processes will assist you in troubles hooting the 24 VAC circuit and ruling it out as a probable cause: • 24 VAC is not present on the interface board J3 pin 9 (LED 5 (GV)) and, on dual units, on J1 pin 9 (LED 1 (GV)).
1-33 24 VOLT CIRCUIT With Interface Board 106-0386 and One 807-3366 (FV) Ignition Module NOTE: Som e u ni ts m a y be wi red in this manner. IGNITION MODULE V1S PWR (left side) V2S LED 5 (GV) J3 PIN 9.
1-34 LEFT VAT IGNITION MODULE LED 2 (PWR) PWR V2D HIGH LIMIT SWITCH LED 1 (GV) GAS VALVE IGNITION MODULE PWR V1D HIGH LIMIT SWITCH GAS VALVE 24V TRANSFORMER LED 5 (GV) J1 PIN 9 J3 PIN 9 RIGHT VAT J3 P.
1-35 1.8.2 Troubleshooting the Gas Valve Prior to checking for problems associated with the ga s valve, ensure that the unit is calling for heat. Also, for non-CE units, verify that the gas valve is in the ON position.
1-36 1. If resistance is not 5 mega-Ohms or greater between each pin and chassis ground, the probe has failed and must be replaced. 2. If resistance is 5 mega-Ohms or greater between each pin and chassis ground, the probe is okay.
1-37 1.9. Simplified Wiring Diagrams 1.9.1 Wiring Diagram for Full-Vat Dual-Spark Module AIR SWITCH ONLY ON CE AND SOME EXPORT UNITS LINE VOLTAGE K3 HEAT & BLOWER RELAY AIR OPTIONAL AIR SWITCH BLO.
1-38 1.9.2 Wiring Diagram for Full-Vat Single-Sp ark Module (Austrailia and Pacific Rim) K3 HEAT & BLOWER RELAY AIR OPTIONAL AIR SWITCH BLOWER HI LIMIT 12 V 24V TEMP PROBE 24V LED 3 LED 5 R-GV R H.
1-39 1.9.3 Wiring Diagram for Dual-Vat Single-Spark Module TD GND ALARM 25V+ RIGHT IGNIT OR VALVE TEMP PROBE BLOWER 24 V OPTIONAL AIR SWITCH 6 J3 1 1 4 8 4 8 9 9 R-HEAT LED 4 K2 HEAT RELAY R-GV LED 5 .
1-40 1.10 Principal Wiring Connections GROUND LINE VOLTAGE L1 GROUND, JUMPE RE D FROM PIN 2 GROUND, JUMPE RE D TO P IN 11 JUMPERED FROM PIN 4 JUMPERED TO PIN 7 JUMPERED TO PIN 6 JUMPERED FROM PIN 12 F.
1-41 1.11 Wiring Diagrams 1.11.1 Pro H50/55-Series Fryer, Multi-vat 8051315C Refer to "PRI NCIPAL WI RING C ONNECTI ONS" on Page 1-41 for detail of connection points J1, J2, J3, C2, C 3, and C5.
1-42 1.11.2 Pro H50/55-Series Fr yer, Single, Full-vat 805-1675.
1-43 1.11.3 Pro H50/55-Series Fr yer, Single, Dual-vat.
1-44 1.11.4 Pro H50/55-Series Fryer, Single, CE.
1-45 1.11.5 Pro H50/55-Series Fr yer, Single, FAST-ready.
1-46 1.11.6 Transformer/Filter Boxes 1.11.6.2 FPH150/155 Transformer/Filter Box EXTRACTE D FROM 8051377B 1.11.6.1 MPH150/155 Transformer/Filter Box.
1-47 1.11.6.3 FPPH 250/255/450/455 Tr ansformer/Filter Box 8051340C.
1-48 1.11.6.4 FPPH 350/355 Transformer/Filter Box.
1-49 1.11.7 Modular Basket Lift (100/120V) 1 2 43 5 6 12 - - - - - 7 8050518E.
1-50 1.11.8 Modular Basket Lift (208/250V) 8 9 10 11 12 7 BLACK GREEN WHITE RED ORANGE BLUE mF 12.5 NC NO M M F m 12.5 NO NC NC NO 1 2 3 4 NO NC 5 6 REFERENCES TO LEFT & RIGHT ARE FROM THE RE AR O.
1-51 1.11.9 Wiring Diagrams – Oil Return/Disposal Oil Return/Wand Wiring (Japan) Oil Return/Disposal Wiring (Sonic).
2-1 PRO H50/55-SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1 Accessories 2 3 4 9 10 11 12 13 5 15 14 6 7 1 8 ITEM PART # COMPONENT 1 803-0271 Basket, Twin 2 803-0099 Basket, Full (cannot be used with ba.
2-2 2.2 Basket Lift Assemblies and Component Parts NOTES: 1. Assemblies 106-1807SP (100-120V) and 106-1810SP (208-250V) do not include Items 8, 16, or 24-33. These items must be ordered separately. 2. For 100-120V units, each individual resistor (807- 2661) may be replaced or the entire reis tor assembly (806-8530SP) may be replaced.
2-3 ITEM PART # COMPONENT 1 200-2942 Mount, Modular Basket Lift 2 806-5964SP Motor Assembly, Modular Basket Lift 3 807-2133 Capacitor, 12.5 μ Farad, 250VAC Motor Run 4 807-2572 Microswitch 5 Resistor.
2-4 2.3 Cabinetry 2.3.1 Backs, Doors, Flue Caps, Sides, and Top Caps 1 2 3 5 7 8 9 4 6 10 12 11 13 14 8 17 18 19 20 21 22 23 15 16 24.
2-5 ITEM PART # COMPONENT 1 Back, Single Uppe r 210-6581 Stainless Steel 200-6581 Cold Rolled Steel 2 Back, Sin g le Lowe r 210-6580 Stainless Steel 200-6580 Cold Rolled Steel 3 Back, Double U pp er (.
2-6 2.3.2 Filter Cabinet Bases, Casters, Framing, and Related Components NOTE: 2- and 3-st ation fryers have 4 casters; 4- and 5-stat ion fryer s have 6.
2-7 ITEM PART # COMPONENT 1 Frame, Control Panel 106-3902SP Two-Station, Standard (use 106-5221SP mfd. After 3.15.06) (use 106-6082 for fall back) 106-3903SP Three-Station, Standard (use 106-5018SP mfd. After 3.15.06) (use 106-6086 for fall back) 106-3904SP Four-Station, Standard (use 106-5019 mfd.
2-8 2.3.3 Non-Filter Cabinet Bases, Casters, Framing, and Related Components NOTE: 2- and 3-station fryer s have 4 caster s; 4- and 5-station fryers have 6. See Page 2- 4 for uppe r hinges. The 5-station cabine t illustrated is typical of all Pro Series (H50/55) gas non-filter cabinets.
2-9 ITEM PART # COMPONENT 1 Fram e, Control Panel 806-4732 Single-Station, Standard (use 106-5016 mfd. After 3.15. 06) (use 106-6079 for fallback) 106-3902SP Two-Station, Standard (use 106-5221SP mfd. After 3. 15.06)(use 106-6082 for fallback) 106-3903SP Three-Station, Standard (use 106-55018SP mfd.
2-10 2.4 Controllers SOLID STATE 1 2 3 4 ITEM *Standard PART # *Euro-Look PART # COMPONENT 1 Computer Magic III.5 106-1151SP 106-3446 Dual-vat (Domestic U.S.) 106-1187SP 106-3447 Dual-vat (CE) (use 106-3450 for 8-second MC Non-CE export uni ts) 106-1150SP 106-3445 Full -vat (Domestic U.
2-11 2.5 Drain, Filtration, and Oil Return System Components 2.5.1 Filtration System Components.
2-12 ITEM PART # COMPONENT 1 108-0181SP Filter Pan, Slid e-type, FootPrint Pro (after July, 2008; includes plug and o-rings) 813-0568 Plug, 1/8-inch NPT Socket Head 816-0596 O-Ring (two required) * 82.
2-13 2.5.2 Drain Valves and Associated Components.
2-14 ITEM PART # COMPONENT 1 810-1569 Valve Assembly, 1.25-inch Full-Vat Non-Filter Drain (includes handle) * 810-1427 Lock Pin Handle for 1.25-inch Valve Assembly 2 806-7915SP Valve Assem bly, 1-inch.
2-15 2.5.3 Oil Return Line Components There are more tha n 160 oil return line combinations. The three example s shown are typical. These examples identify all of the components used in the vari ous con- figurations, but not all o f the components identified are used in every configuration or in only the position shown.
2-16 ITEM PART # COMPONENT 1 807-2484 Valve, 1/4-inch NPT Solenoid 2 810-0278 Valve, 1/2-inch NPT Ball 3 806-8762SP Valve Assem bly, Microswitch and Ball 4 900-5953 Handle, Oil Discharge Valve 5 814-0.
2-17 2.5.4 Oil Return Handle, Oil Disposal and Disposal Hose Components Left Hand l e and Linkage (Standard) 1 2 3 4 6 5 7 9 10 11 5 6 12 13 14 13 15 16 17 18 19 1 5 6 4 2 3 8 9 10 11 17 19 18 12 13 1.
2-18 ITEM PART # COMPONENT 1 807-2103 Microswitch, Lever Activated 2 826-1359 Screw, 4-40 X 3/4-inch Slotted Round Head 3 809-0237 Nut, 4-40 Hex Keps 4 200-0821 Bracket, Handle 5 809-0247 Nut, 8-32 Hex Keps 6 826-1363 Screw, 8-32 X 1/2-inch Slotted Truss Head (pkg.
2-19 2.5.5 Oil Disposal Wand Assembly 1 2 3 ITEM PART # COMPONENT 806-7459 Assembly, Oil Disposal Wand 1 810-0603 Wand, FB Filter 2 810-1471 Hose, 24 FPH50/55 3 810-0490 Quick Disconnect, ¼-inch Female 2.
2-20 2.5.7 Rear Flush Oil Return Components 21 (All components except for Items 4 and 5 are the same for Right a nd Left Oil Re turn Valve Assemblies) Nut (furnished with Item 8) 15 19 11 10 2 3 12 4 .
2-21 ITEM PART # COMPONENT 1 Valve Assembly, Microswitch and Ball Valve 106-3452 Valve, Rear Flush Assembly, Left Side 106-3453 Valve, Rear Flush Assembly, Right Side 2 810-2493 Elbow, 90º x ¼-inch .
2-22 2.5.8 Power Shower Assemblies (Optional) 2 1 3 4 ITEM PART # COMPONENT 806-4442SP Power Shower Assembly, Full-vat, Complete 806-4476SP Power Shower Assembly, Dual-vat, Complete 1 814-0001 Grip, Handle 2 809-0415 Screw, Cleanout 3 826-1390 Seal (Gasket) (pkg.
2-23 2.6 Electronics and El ectrical Components (for Controllers, Page 2-10) 2.6.1 Component Boxes.
2-24 ITEM PART # COMPONENT 1 810-1164 Block, One-Piece Screwless Terminal 2 200-5996 Box, One-Piece Component 3 807-1926 Bushing, .875-inch Split 4 826-2024 Cable, 21-inch Ignition (comes with Rajah c.
2-25 2.6.2 Transformer Boxes 1 4 15 20 30 18 22 25 13 30 2 12 34 30 17 30 11 27 23 14 10 1 4 15 20 30 18 22 25 13 30 2 34 3 30 17 30 11 27 23 14 20 30 A B C 5 8 15 9 6 7 20 30 13 30 20 30 20 30 35 33 .
2-26 ITEM PART # COMPONENT Box Assembly, Transformer A 106-1380SP 100-120V FMPH150/155, FMPH350/355, FMPH450/455 B 106-0627SP 100-120V FMPH250/255, FMPH350/355, FMPH450/455, FPPH250/255, FPPH350/355, .
2-27 2.6.3 High-Limit Thermostat and Temperature Probe ITEM PART # COMPONENT 1 826-1177 High Limit Thermostat - 425 ° F/218 ° C 2 806-4206 Temperature Probe 3 210-0681 Probe Guard.
2-28 2.7 Frypots and Associated Components 2.7.1 Full-Vat Frypot Components 1 41 10 38 3 29 21 40 7 16 13 14 17 35 18 33 15 22 36 11 25 30 37 23 26 8 5 12 31 6 39 9 20 4 24 32 13 34 17 40 7 21 27 19 2 All insulation and gaskets can be ordered in a sing le kit, P/N 826-0929.
2-29 ITEM PART # COMPONENT 1 106-1019SP Flue Assem bly, Full-vat 2 200-0936 Back, Left Full-vat Combustion Chamber 3 200-0937 Back, Right Full-vat Combustion Chamber 4 200-2227 Retainer, Full-vat Uppe.
2-30 2.7.2 Dual-Vat Frypot Components.
2-31 ITEM PART # COMPONENT 1 106-1018SP Flue Assem bly, Dual-vat 2 200-0941 Back, Dual-vat Combustion Chamber 3 200-2229 Retainer, Dual-vat Upper Insulation 4 809-0059 Nut, 1/4-20 Flange Hex 5 809-036.
2-32 2.8 Gas Supply and Combustion Sy stem Components PH250/255 Full Vat Gas Manifold (Typical) The example illustrat ed is typical of PRO Series Fryer Gas Manifolds. Each manifold is assembled from stand ard 1/2- , 3/4-, and 1-inch NPT black iron pipe nipples, elbows, tees, plugs, and unions, which may be locally aquired .
2-33 ITEM PART # COMPONENT 1 Ignitor (includes gasket 816-0059, which may be ordered separately) 826-0981 Natural Gas (G20, G25) 826-0982 Propane (G30, G31) 826-1002 Manufactured Gas 2 826-1371 Screw, #8 X 1/2-inch Hex Head (pkg.
2-34 2.9 Gas Valves and Associated Components Non-CE Gas Valve Assembly (Typical) CE Gas Valve Assembly (Typical) 5 1 2 3 4 6 7 8 9 10 11 12 13 14 15 13 22 16 18 17 19 20 21 10 11 23 NOTE: The gas tub.
2-35 ITEM PART # COMPONENT 1 Valve, Non-CE Gas 826-1122 Natural Gas (G20, G25) 826-1123 Propane Gas (G30, G31) 2 810-1715 Valve, CE Gas (G20, G25, G30, G31) 3 810-1041 Accessory Kit (contains parts to.
2-36 2.10 Wiring Assemblies and Harnesses Filter A ssociated Wiring 1 2 3 ITEM PART # COMPONENT 1 810-1062 Cable, Filter Box Lower 9- Pin Plug to 807-2000/2001 C2 Connector * 807-2000 Cable, 810-1062 .
2-37 Main Wiring Harnes ses U.S. and Non -CE harness (shown) has two u ntermin ated wire s . Untermin ated wire s. CE harness h as two unt erminat ed wires plus two additional wires with push- on term inals . ITEM PART # COMPONENT 807-1978 U.S. and Non-CE Export Main Wiring Harness 807-2168 CE Main Wiring Harness 807-4014 U.
2-38 2.11 Miscellaneous Connectors and Terminals 1 2 4 5 3 6 7 9 10 8 11 13 12 ITEM PART # COMPONENT 1 807-1068 2-Pin Female 2 807-0158 6-Pin Female 3 807-0156 9-Pin Female 4 807-0159 12-Pin Female 5 .
3-1 PRO H50/55-SERIES GAS FRYERS CHAPTER 3: SINGLE H50/55 UNIT UNIQUE PARTS LIST 3.1 Single H50/55 Filtra tion System Components ITEM PART # COMPONENT 806-9255SP Filter Pan Assem bly, FootPrint Pro Fi.
3-2 3.2 Single H50/55 Oil Return Components 18 17 1 3 5 7 8 2 4 16 14 15 11 11 10 9 8 10 9 6 7 13 12 12 Dual-vat Oil Return Manifold Full-vat Oil Return Manifold ITEM PART # COMPONENT 1 108-1030 Mount.
3-3 3.3 Single H50/55 Component Boxes.
3-4 ITEM PART # COMPONENT 1 106-6708 Interface Board, SMT, Gas, non-Basket Lift, FV (U.S., Canada, Mexico) 2 826-2264 Interface Board, SMT, Gas, with Basket Lift, FV (U.
3-5 3.5 Single H50/55 Transformer Boxes ITEM PART # COMPONENT 1 900-2697 Transform er Box 2 900-2703 Cover, Front, Large 3 900-2709 Cover, Front, Small 4 900-2708 Cover, Transformer Box 5 806-6164 Har.
Frymaster, L.L.C., 8700 Line Av enue, Shrev eport, Louisiana 71106 TEL 1-318 -865-1711 FAX (Par ts) 1-318- 219-7140 FAX (Tech Support) 1-318-21 9-7135 PRINTED IN THE UNITED STATES SERVICE HOTLINE 1-80.
Ein wichtiger Punkt beim Kauf des Geräts Frymaster FOOTPRINT H50 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Frymaster FOOTPRINT H50 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Frymaster FOOTPRINT H50 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Frymaster FOOTPRINT H50 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Frymaster FOOTPRINT H50 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Frymaster FOOTPRINT H50 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Frymaster FOOTPRINT H50 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Frymaster FOOTPRINT H50. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Frymaster FOOTPRINT H50 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
